Landscape Forms Marneaux Table User manual

IncludedComponents
•(1)Tabletop
•(1)TableSupport
•ForCatenaorSteelheadtabletop:(4)1/4‐20x3/4"Phillipstrussheadtappingscrews
•ForMarneaux®tabletop:(4)1/4‐ 20x5/8”Phillipsmachinescrewswithwashers
Forumbrellaoption:AnyLandscapeForms’umbrellasecuresdirectlytoalltable
supports.Additionalumbrellasurfacemountstandisnotrequiredforusewithtables.
•Umbrellaconnection:(1)1/4‐20Phillipspanheadmachinescrewand(1)locknut
‐2‐3/4”lengthforØ18”Catenabase
‐3‐1/4”lengthforØ23”Catenabase
TabletopAssembly:
Note:ForCatenaSupportOption:UseØ18”supportfor24”and30”tables.UseØ23”
supportforallothers.
1. Placetabletopupsidedownonnon‐marringlevelsurface.
2. Placetablesupportupsidedownontabletopandalignholes.
Theuseofpowerdriversisnotrecommended.Threadsorthreadedinsertsmaybe
damagedorbrokenduetoover‐torqueing.
3. Installhardware.Tightenalltabletopfastenersuntilsnug,thentightenadditional
1/4turn.
4. Turntablerightsideupusingatleasttwopeople.
5. Freestandingtablecanbesetinposition.
SurfaceMountInstallation:
1. Placeunitindesiredposition.
2. Marktheholes.
3. Movetheunitanddrilltheholes.
4. Placeunitinpositionandinstallwithanchorsaccordingtoanchormanufacturer’s
recommendations.
Catena
Stainlesssteel
Orpowdercoat
Steelhead
Perforated
Steelhead
Solid
Marneaux®
ToolsRequired
•ForCatena,Steelhead,orMarneaux®tabletop:#3Phillipsscrewdriver
•Forumbrellaoption:#3Phillipsscrewdriverand7/16”wrench
•(3)Non‐corrosiveanchors,maximumØ3/8”[9mm].
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.Toprotect
thisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamorothernon‐
marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardortextured
surface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthe
finishcausedbyassemblytools.
Installation Guide
Tables Marneaux®, Catena, Steelhead Tabletops with Catena support
www.landscapeforms.com Ph: 800.521.2546
Date: May 21, 2018
Page 1 of 2
UmbrellaAssembly:
1. Toinstallumbrella,slideumbrellapolethroughholeintable.
2. Alignholesinbasetubeandumbrellapole.Insertlong1/4‐20machinescrewand
securewithlocknut.
CAUTION:Donotletgooftheumbrellauntilthepolehasbeensecured.
Recommendedhardware:
Althoughinstallerisresponsibleforanchoringprocedureandhardware,wesuggest
thefollowing:
Forpouredconcreteinstallation:
•3/8"diameterwedgeorsleevetypeexpansionanchoratleast3"long,or3/8”‐16
x4”threadedanchorrodwithanchoringadhesive
Forpaverinstallation:
•Ifpaversareinstalledoverpouredconcrete,use3/8"diameterwedgetype
expansionanchorwithenoughlengthtogothroughbrickandintoconcrete
Forwooddeckinstallation(atleast2"nominalthickness):
•3/8"hexheadlagscrewatleast2"long

ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.Toprotect
thisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamorothernon‐
marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardortextured
surface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthe
finishcausedbyassemblytools.
Installation Guide
Tables Marneaux®, Catena, Steelhead Tabletops with Catena support
www.landscapeforms.com Ph: 800.521.2546
Date: May 21, 2018
Page 2 of 2
SUPPORT
SCREW
TABLETOP
(CATENA
SHOWN)
Tabletoptosupportassembly Catenabase,Ø18” Catenabase,Ø23”
Catenaanchor
tabdetail
Catenabasedetails