Larry vs Harry Twin Seat User manual

Twin Seat
Assembly Manual

Before you start
Note!
Important message
from Larry the King.
2 3 4
Things you need to attach your Twin Seat
Tools you need
Find your tools and get ready!
1
Phillips 3
Screwdriver
10mm
Wrench/Spanner
3mm
Hex/Allen Key
Grease
(metal on metal)
Grease.
Remember to grease or else
your mechanic will hate you later on.
(“Muc-o” has a Bio Grease
that cares about the environment)
Icons that will appear throughout the guide:
You haven’t mounted the Canopy yet?
Find the Canopy Assembly Manual in the Canopy Box or at
larryvsharry.com/owners
Note: It is possible to attach Twin Seat without the Canopy,
but you need the Honeycomb Board!
2
Bullitt with Honeycomb Board and
Canopy attached.

Head Rest
Seat
Base
Two 5-point Harnesses
Components What’s in the box?
Base
Page 5
Harnesses
Page 5
Head Rest
Page 
Seat
Page 7
3
A
B
C
D

Step 1
Foldable Seat: Loosen 2 nuts and
2 bolts on the back of the Bullitt
frame with 5mm Allen Key and
13mm Wrench.
Armrest in Canopy: Loosen 2
nuts on the armrest on the inside/
outside of the Canopy using 5mm
Allen Key and 13mm Wrench.
Larry the King says:
“If you have installed the
Bullitt Foldable Seat and want
to replace it with the Twin Seat,
you loosen the two bolts and
two nuts and remove the Seat,
before you follow the rest
of the manual.”
Two tips before you start installing the Twin Seat,
if you have the Foldable Seat mounted!
Both sides
Nuts
Bolts
1 2
2
4

Step 2
Attaching the Base + 5-point Harnesses
Align bolts with holes in the
back (1) and in the center (2) of
the Honeycomb Board.
Place Base (3) in the bottom, inside the Canopy
Point backward towards the back of the Canopy
Point forward towards the headtube of the Bullitt
Note! Make sure the seat belt
buckles point inwards (under-
neath the foamy part) before
attaching the bolts.
1 1
2
Attach the 5-point Harnesses
to the buckles in the bottom.
Fold them forward/up, so you can
see what you are doing next.
Grease your center bolt and
mount it in the bottom center
loosely so you can align the rest.
Mount the 2 bolts (from the back
/outside of the Canopy) to the
tubes (1). Add washers to the 2 bolts.
Grease bolts.
Tighten the nuts, so the Twin Seat
tubes sits closely to the frame.
Tighten the center bolt too.
Click!
Click!
x2
1 2
3
5 6
4
A B
5-6 Nm
5

Step 3
Attaching the Head Rest
Align 4 holes on the back of the
Canopy/armrests with the holes
in the Bullitt frame.
Align Head Rest with the 4
holes (make sure it turns the
right way up). Slide the 4 bolts
through the holes.
Grease bolts! Add washers to the bolts.
Put the 4 nuts from the back/
outside of the Bullitt frame
onto the Head Rest bolts.
Tighten with 3mm Allen Key.
This way up!
1 2
3 4
5
C
5-6 Nm
6

Step 4
Attaching the Seat
Loosen 2 bolts in the red
adjustable mounts with a 5mm
Allen Key.
Slide the red adjustable mounts
backwards.
Before placing the Seat, turn the
Seat around and make sure the
seat belts are slid out to the
sides of the tube!
Put center-tube of the Seat in
the notch close to the red
mounts. Slide the red adjustable
mounts back.
Tighten 2 bolts with 5mm
Allen Key.
Attach the Harnesses to the
buckles! That’s 4 buckles for
each belt: Two on the Seat, two
on the Head Rest.
This way up!
x2 Slide! x2
Slide back
Top
buckles
Seat
buckles
Slide back
Right!
Buckles
Wrong
D
1 2
3
5 6
4
5-6 Nm
7

Extra Features
Nice features to note with the Twin Seat
The 5-point-Harnesses can easily
be converted for use with one
child for a more balanced ride.
Adjust the height of the harnesses
by easily pulling the straps up or
down by the top.
Small compartment room behind
the seats for locks or things to
make life easier - just pull the
seat outwards.
The compartment room is held
together by very strong magnets.
The single kid 5-point-Harness is
placed in the middle of the seat.
1
2
33.1
1.1
8

All rights reserved © 2022 Larry vs Harry
Ver.No.: 01, 12-2021
www.larryvsharry.com
Bullitt Copenhagen
Frederiksborggade 43, DK–1371 Copenhagen, Denmark