Larson Electronics WDL-12-70W-LED-SFC-WCM User manual

WDL-12-70W-LED-SFC-WCM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
22W Wash Down LED Light
1120/277V AC - Food Safe - IP66 Rated - Surface Mount
Instruction Manual
Thank you for your purchase of the Larson Electronics WDL-12-70W-LED-SFC-WCM.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE WDL-12-70W-LED-SFC-WCM MUST BE WIRED IN ACCORDANCE WITH NATIONAL
ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
This WDL-12-70W-LED-SFC-WCM Wash Down LED Fixture offers 3,126 lumens of crisp white light with a CRI of 80 and a color
temperature of 5000K. -This NSF rated unit contains impact and shock resistant, no-glass polycarbonate LED bulbs, and sealed and
corrosion resistant aluminum hardware, providing reliable, stable lighting under even the harshest of conditions in food processing and
preparation applications. This 22-watt LED light operates on 120-277V AC @ 50/60 Hz, and features a dimmable electronic driver and
IP66 waterproof protection.
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
MOUNTING
The WDL-12-70W-LED-SFC-WCM includes a set of two adjustable surface mounts with stainless steel adjustable brackets
for safe and easy mounting to any flat surface.

WDL-12-70W-LED-SFC-WCM
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
INSTALLATION
This fixture is shipped with preconfigured Housing Color, Color Temp, and Lens type. See product label for specific unit
received.
1. Install fixture to surface via the mounting brackets. There are predrilled holes for mounting.
2. If needed, open lens by unscrewing the two screws. Be careful not to drop lens or internal components when opening.
3. Electrical voltages and frequency are listed on the product label for reference.
4. For supply connections use conductors suitable for min. 90° C.
5. Connect internal wires per wiring diagram, and wire through hub according to NEC requirements using conduit or
similar device.
6. Replace lens and secure screws.
7. Close all unused end caps.
MAINTENANCE
Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by
the environment and frequency of use. It is recommended that inspection be performed a minimum of once a year.
WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND
MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND
COMPETENT ELECTRICIAN.
1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible
problem and should be thoroughly investigated and repaired as necessary.
2. Inspect contacts for signs of wear and replace if necessary.
3. Clean exterior surfaces making sure nameplates remain legible.
If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This
condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the
proper replacement part(s) before continuing service.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine checks to be
made on a yearly basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow
an Electrical Preventive Maintenance Program as described in NFPA 70B: Recommendedpractice for
Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance. Clean the
lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or contamination (i.e.
excessivedust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The WDL-12-70W-LED-SFC-WCM is designed to provide years of reliable performance. Should the need for
replacement parts arise, please contact Larson Electronics.