Larson Electronics EPLC2-QP-1X70LED-100 User manual

EPLC2-QP-1X70LED-100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 3
50W Tripod Mounted Food Safe LED Light
Explosion Proof - C2D1 - 100' Cord - EXP Plug
Instruction Manual
This explosion proof light tower is designed for illumination of industrial locations. It uses the
latest in solid state lighting technology for long life, low maintenance and high efficiency.
The unique design focuses the light where it is needed, giving improved efficiency over a
conventional HID luminaire.
An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any
nominal 100-277V AC 50/60 Hz power supply without any variation in light output.
WARNING
To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected
and maintained by a qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
•Be certain electrical power is OFF before and during installation and maintenance.
•Luminaire must be connected to a wiring system with an equipment-grounding conductor.
To avoid explosion:
•Make sure the supply voltage is within the luminaires’ voltage rating.
•Ensure the marked T rating is less than the ignition temperature of the Hazardous
Atmosphere.
•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
•Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
For supply connections, use wire rated for at least 110°C
TRIPOD ASSEMBLY
The tripod assembly consists of 3 parts:
1. Light head
2. Pole w/Legs
3. Wheel base
To assemble tripod, begin by placing the legs over the wheel base. Tighten bolt to secure the wheels.
The tripod can now be rolled around on its wheels. Ensure the legs are folded up before tilting tripod
to maneuver.
WARNING: Use caution before tilting tripod with a heavy load. For heavy loads, it is recommended to
remove the light head prior to transporting via wheel base! Failure to do so may cause serious injury
or death. Larson Electronics shall not be held liable for injuries caused by misuse.
1. Place tower in desired location that is flat and able to support the tripod without falling over.

EPLC2-QP-1X70LED-100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 3
2. Loosen hand screw and lower legs until firmly stabilizing tripod.
3. Tighten hand screw to secure legs.
4. With help, place the light head over top pole and tighten hand screw.
Light weight lamps can be attached by tilting tripod toward the ground with the legs up. Attach light
head to pole, tighten hand screw and tilt back to its vertical position. DO NOT tilt tripod while
extended to max height. It is recommended to have another person hold the tripod while tilting
vertically.
For heavy weight lamps, use a ladder and extra help for attaching light head to pole.
Double check that all hand screws are tight before continuing use of the light tower.
EXTENDING
1. Loosen hand screw for extending the light head. Once loose, extend light head until desired
height is achieved with at least 1ft - 2ft remaining inside pole for support.
WARNING: DO NOT over extend light head completely allowing extension pole to free from base! If
the light head becomes free, serious injury or death can occur. Larson Electronics shall not be held
liable for injuries caused by misuse.
2. When desired height is achieved, tighten hand screw to secure light head.
LOWERING
1. To lower mast, grasp light head and slowly loosen hand screw. Lower the light head and
tighten hand screw.
WARNING: DO NOT loosen hand screw allowing light head to fall freely. This can damage the unit
and cause serious injury or death. Always grasp light head before lowering. Larson Electronics shall
not be held liable for injuries caused by misuse.
The tripod mount light tower can be disassembled for storage or transporting. Unplug light from power
source and remove light head following previous steps for attaching.
Once the light head has been removed, loosen hand screw for legs and fold them up. Wheel to
desired location or remove from wheel base for complete disassembly.
THE LENS AND CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, SCRATCHES OR
ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE PARTS MUST BE REPLACED
BEFORE RESUMING USE OF THE LIGHT TOWER.
The EPLC2-QP-1X70LED-100 is designed to provide years of reliable lighting performance. Should
the need for replacement parts arise, please contact Larson Electronics at the contact information
below.

EPLC2-QP-1X70LED-100
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 3
WIRING (see attached wiring diagram)
This unit comes preconfigured with selected cord cap, and beam spread. Once deployed, plug cord
cap into compatible receptacle with Voltage: 100-277 Volts AC, 50/60Hz
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool
down before performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens
will void the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend
routine checks to be made on a yearly basis. Frequency of use and environment should
determine this. It is recommended to follow an Electrical Preventive Maintenance Program
as described in NFPA 70B: Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric
performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use
mild soap or a liquid cleaner.
3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions
or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if
needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
REPLACEMENT PARTS
The EPLC2-QP-1X70LED-100 is designed to provide years of reliable performance. Should the need
for replacement parts arise, please see part numbers below and product drawings.
Some parts may be sourced locally from your nearby hardware store.
Description:
Part Number:
Tripod assembly:
ALU-TP-W-712
50W Explosion Proof Light Head:
EPL-HB-50LED-RT
WARRANTY
Should further information not covered by these instructions be required, please contact Larson Electronics at
1-800-369-6671 or [e-mail] for further assistance.
Please visit LarsonElectronics.com for Warranty and Return information.
WARNING: CHECK NAMEPLATE
FOR PROPER VOLTAGE. DAMAGE
FROM IMPROPER VOLTAGE WILL
VOID WARRANTY.