Larson Electronics EPLX-SL-PT-3X80W.RD2-TRC-20X-100C User manual

EPLX-SL-PT-3X80W.RD2-TRC-20X-100C
240W Explosion Proof Pole Top AC LED String Light
C1D1/C2D1 - Group B + ATEX/IECEX - 100' SOOW Cord
Instruction Manual
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPLX-SL-PT-3X80W.RD2-TRC-20X-100C from Larson Electronics is an Explosion Proof Pole Top Mount AC LED
String Light that is a compact powerhouse built to withstand demanding conditions. This LED pole top mount lighting
system features three, state-of-the-art AC LEDs paired with specially designed heat sinks for improved efficiency, thermal
management, and durability. Available in 5000K cool white and 3000K warm white options, a 110° flood beam provides
crisp, and bright illumination with broad coverage. Line-in power is facilitated by a 100' 16/3 SOOW cord with an explosion
proof cord cap.
Mounting
The EPLX-SL-PT-3X80W.RD2-TRC-20X-100C pole top slip
fit mount explosion proof LED string light features adjustable
swivel brackets constructed of 3/8" aluminum that allows
over 270° of adjustment and are attached to slip fit yokes for
easy installation. The slip fit yoke is built to customer's
specs, enabling operators to mount this explosion proof LED
lighting system to their specific pole size. Slip each light over
it's mount pole, and tighten the T-handle screw to secure in
place. Set vertical angle using adjustment holes on the sides
of the swivel brackets to aim the lights where desired.
Power
This explosion proof LED string light is equipped with 100 feet of 16/3 SOOW line-in cord that is fitted with an explosion
proof cord cap for easy connection to explosion proof outlets.
We strongly encourage a licensed electrician install this product, in all locations, especially in outdoor areas where
weatherproofing may be required.
Warning: Check product label for correct input voltage!
This unit comes pre-wired from the factory with the selected cord cap. Take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the unit. All outdoor installations and indoor
installations near a wet location require the use of a GFCI device for safety, according to the National Electrical Code®
(NEC). Ensure the unit is properly grounded.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
EPLX-SL-PT-3X80W.RD2-TRC-20X-100C
Position device near work area for operation. Run cable to nearby power source. Insert and twist-lock explosion-proof
plug into a compatible receptacle within the hazardous environment. See plug operation below.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into receptacle and
rotated clockwise.
1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all the way
into receptacle until it cannot go further.
2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also mechanically locks
plug into receptacle so it cannot be pulled out.
3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.
MAINTENANCE
Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool downbefore
performing maintenance.
Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will voidthe
warranty.
1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine
checks to be made on a yearly basis. Frequency of use and environment shoulddetermine this. It is
recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommendedpractice for Electrical Equipment.
2. The lens should be cleaned periodically as neededto ensure continued photometric performance.
Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e.excessivedust build-up). Clean with a non-abrasive clothif needed.
4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of children
when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPLX-SL-PT-3X80W.RD2-TRC-20X-100C is designed to provide years of reliable performance. Should the need for
replacement parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.