Larson Electronics TPM-2XWP60E-25C User manual

TPM-2XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 1
120W LED Light with Telescoping Pole Mount
3' to 8.5' - 10,800 Lumens - 120-277VAC - 25ft Cord
Instruction Manual
Thank you for your purchase of the Larson Electronics TPM-2XWP60E-25C.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE TPM-2XWP60E-25C MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE
AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
The TPM-2XWP60E-25C from Larson Electronics is an Industrial LED Light with Telescoping Pole that offers high light output from a
compact form factor, and is designed to provide a more durable and long lived alternative to halogen and metal halide units. This
powerful, telescoping LED light produces 10,800 lumens, operates on 120 to 277V AC, features a telescoping pole that is adjustable
from 3 to 8.5 feet, and includes a mounting plate with four predrilled holes for easy mounting on flat surfaces.
WIRING
This general use telescoping LED light fixture is equipped with 25 feet of 16/3 chemical and abrasion resistant SOOW cord
that is fitted with an industrial grade cord cap for easy connection to common wall outlets. Plug options include standard
5-15 15 amp straight blade plug for 110V wall outlets with ground, standard 6-15 15 amp straight blade plug for 220-240V
wall outlets with ground, NEMA L5-15 15 amp twist lock plug for 125V twist lock outlets, NEMA L6-15 15 amp twist lock
plug for 240V twist lock outlets, British BS1363 13 amp fused 3-blade plug for United Kingdom outlets, or a two pin 16 amp
rated Schuko plug with ground contact and socket for European outlets up to 250V. Alternatively, we can provide flying
leads with no plug for hard wire applications or for operators who prefer to wire in user provided cord caps. Please choose
pigtail option below for flying leads with no plug.

TPM-2XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 1
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Standard Cord Cap
This unit comes pre-wired from factory with the selected cord cap. Take
precautionary steps for weatherproofing all connections if installed in a
location where water may come in contact with the unit. All outdoor
installations and indoor installations near a wet location require the use of a
GFCI device for safety, according to the National Electrical Code® (NEC).
Ensure the unit is properly grounded.
POWER
These lights operates on 120 to 277V A and providing versatile power connection options. Each lamp draws just 0.5 amps
at 120 VAC.
MOUNTING
The TPM-2XWP60E-25C features a telescoping pole that is adjustable from 3 to 8.5 feet. The telescoping pole features a
mounting plate that has four predrilled holes for easy mounting to flat surfaces. This pole features a pneumatic braking
system that prevents unexpected or sudden collapse of the pole. If the pole is loaded with a pair of heavy fixtures for
instance and the operator inadvertently releases the locking tabs, the pole will simple ease down gently rather than
suddenly collapse.
1. Utilize the predrilled holes and mount the flat bracket in a location that can
support the load.
2. Place telescoping pole in the base mount and tighten base mount hand
screw until tight.
3. Position light head over top pole on tripod and tighten black adjustment knob
until tight.
4. Loosen black adjustment knob for each sleeve to extend tripod. Extend top
pole, then bottom pole when elevating.
5. Tighten adjustment knob(s) once the desired height is achieved.
6. Attach power cord to compatible outlet with voltage listed on nameplate.
Voltage: 120-277V AC 50/60Hz.
USING THE TRIPOD
NOTE: Route cable in a safe manner to prevent trip hazards or accidental snags.
LED OPERATION
The light head features a single 50 watt LED work light. This light is “instant on” and
will illuminate once power is supplied. Do not look directly into lights when powering.
Lamp can be adjusted with the adjustment screws on the sides. Tighten screws once
desired angle is achieved.
- Light Head
Adjustment
Points
-Leg Sleeve

TPM-2XWP60E-25C
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The TPM-2XWP60E-25C is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.