Larson Electronics EXP-EMG-EXT-LE6-1L User manual

EXP-EMG-EXT-LE6-1L
Explosion Proof Bug Eye Emergency LED
Fixture Instruction Manual

1
Congratulations on the purchase of your new Explosion Proof Bug
Eye Emergency LED Exit Fixture. Please read these instructions
carefully to familiarize yourself with the safe operation and
maintenance of your new emergency fixture. Following these
instructions will insure many years of safe and dependable service.
Table of Contents
I. Installation & Operation 2
I.I Installation 2
2
I.
II. Trouble-Shooting & Maintenance 3
II.I Trouble Shooting 3
3
II.II Maintenance
III. Safety Warnings & Ratings 4
4 III.I Warnings
III.II Ratings 4
**Please visit our website for all warranty/return related questions.
II Operation

2
Return to Table of Contents
I. Installation & Operation
NOTE: The EXP-EMG-EXT-LE6-1L is designed to be surface mounted to flat surfaces such
as walls.
I. Installation
Mounting for this fixture is achieved via
mounting tabs located on the back side
of the light.
The EXP-EMG-2L-LE6 explosion proof
emergency self-testing LED fixture is NOT
a factory sealed fixture. Operators will bring
their own rigid conduit to a junction box and
complete their connects. Cap off any hubs
that are not in use.
Both battery legs must be connected
together. This prevents the battery from
draining during storage and transit. DO
NOT CONNECT HIGH VOLTAGE TO
BATTERYLEGS.
II. Operation
1. ApplyAC power to the light. The LED
indicator will turn RED.
2. See wires labeled for connections.
3. Use appropriate methods for wiring
within hazardous areas following all
appropriate NEC codes. Consult an
electrician if unsure.
4. In the event of power loss, the fixture
will illuminate all lights automatically.
Once power is restored, the lights
will turn off and the batteries will
charge.
Mounting Tabs

3
Return to Table of Contents
II. Trouble-Shooting and Maintenance
CAUTION: Always turn AC power to the equipment OFF before servicing. Servicing should be
performed only by a qualified service technician.
I. Trouble-Shooting
1. Problem:Emergencylightsdonotoperate.
If the charge indicator light is OFF, check
that the circuit breaker for AC supply is ON.
If the charge indicator light is OFF, check
that they battery is properly connected. If the
problem persists, replace the battery.
2. Problem: Emergency lights are dim.
The battery might not be fully charged.Allow
battery to recharge for 24 hours and then
retest. If the lights are still dim, replace the
battery.
II. Maintenance
1. Battery: The battery supplied in the fixture
requires no maintenance. However, it should
be tested periodically and replaced when it
no longer operates the connected fixtures
for the duration of a 30-second or 90-minute
test.
2. Other: Clean lenses and replace lamps as
and when required.
Charger/Battery Fault
LED

4
Return to Table of Contents
II I. Safety Warnings and Ratings
I. Warnings
WARNING: Risk of electric shock -never
connect to, disconnect from or service while
equipment is energized.
WARNING: Risk of fire -Lamps are hot.
Keep combustible material away from the
hot parts. Observe lamp manufacturer’s
warnings, recommendations and restrictions
on lamp operation and maintenance. Make
sure lamps are correctly installed.
The battery in this emergency fixture may
not be fully charged. After electricity is
connected, let the battery charge for at least
24 hours.
Consult local building code for approved
wiring and installation.
Disconnect AC power before servicing and
installation.
DO NOT use this electrical equipment for
anything other than its intended use.
The use of accessory equipment is not
recommended by the manufacturer and will
void product listing and warranty and may
cause unsafe conditions.
Any service on this equipment should be
performed by qualified personnel only.
Cap unused wires with enclosed wire nuts or
other approved method.
Make sure wire terminations are secure and
leads are properly tucked in appropriate wire
channels.
II. Ratings/Approvals
Class I, Divisions 1 & 2 Groups A, B, C, D
Class I, Zones 1 & 2 Groups IIB + H2
Class II, Divisions 1 & 2 Groups E, F, G
Class III, Divisions 1 & 2
90 Minute Emergency Runtime
24 Hour Battery Recharge Time
Self-Testing Unit
Horizontal and Vertical Adjustable