Larson Electronics IL-LED-27R User manual

LLP-JD-TR-8320
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
LED Light Package for John Deere 8320 Tractors - (2)
LED25WRE-CPR - (4) IL-LED-27R
Instruction Manual
Familiarize yourself with all procedures outlined within this instruction sheet.
WARNING:
READ CAREFULLY BEFORE OPERATING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
Never place spotlight face down when light is on. Doing so could burn/ignite surfaces such as seats, carpeting,
etc. and cause major property damage. Always turn spotlight off when not in use.
To prevent serious damage to eyesight, never look into spotlight when light is on.
DO NOT shine light into the face of someone else.
DO NOT touch lens of spotlight when light is on or if it was recently on. The lens will be hot.
DO NOT allow children to handle or operate this spotlight.
DO NOT use this product for other than its intended use.
DO NOT operate in close proximity of combustible or flammable materials.
DO NOT attempt to operate this spotlight if cord, plug, battery, bulb or any part of the spotlight is damaged or
corroded.
The LED25WRE-CPR is shipped with selected cord for powering the fixture. Images shown may vary depending
upon options selected.
POWER
1. The spotlight is designed to work on 12-32 volts DC. This variable voltage
allows the light to be connected to consumer vehicles and other non-standard
power supplies such as military vehicles and heavy equipment.
PLEASE NOTE: There is no difference in light output between voltages.
2. Power transformers (DCP-11-DP) can be purchased through our website to run
this spotlight from household wall outlets.
MOUNTING
The LED25WRE-CPR is suspended within a form fitting trunnion (yoke-type)
mount. This trunnion mount has two screws that can be loosened, allowing the
LED light to be adjusted vertically, then re-tightened to lock the light into the
desired position. A single stainless steel stud protrudes from the bottom of the
mount, enabling the operator to install the light using a simple through-hole mount,
allowing the unit to be installed anywhere a 1/2-inch hole can be drilled.
DETACHABLE CORDS
Power is attached via a weatherproof 2-pin Deutsch connector.
The cords are detachable by depressing the tab on the top of the connectors.
This enables the operator to leave the cord connected to the power source
and remove to store the light.
Additional or replacement cords can be ordered from our website.
*We offer 16 foot coil cords with a cigarette plug (C-16-CC-CP), 21 foot cords with ring terminals (C-21- RT), 16
foot cords with battery clamps (C-16-BC), and 16 foot straight cords with cigarette plugs (C-16 CP).
-LENS
REFLECTOR
Mounting Bolt
Deutsch -
Connector
Adjustment
Screws-
*LAMP STYLE MAY VARY
High Intensity LED Light 25 Watt LED - 12-32V DC - 1000ft Spot Beam

The IL-LED-27R LED Flood Light offers high light output from a compact form factor and is ideal for a wide range of uses
including heavy equipment, boating, vehicle, military, law enforcement and industrial manufacturing applications. This unit
produces a 2160 lumen light output with very low amp draw, 30,000 hour service life and 10 to 30 volt compatibility which
provides operators with a compact and powerful LED lighting solution.
POWER
•The flood light is designed to work on 10-32 volts DC. This variable voltage
allows the light to be connected to consumer vehicles and other non-standard
power supplies such as military vehicles and heavy equipment.
PLEASE NOTE: There is no difference in light output between voltages.
Power transformers (DCP-11-DP) can be purchased through our website to run
this flood light from household wall outlets.
MOUNTING
The IL-LED-27R is suspended within a form fitting trunnion (yolk-type) mount. This
trunnion mount has a single bolt that can be loosened, allowing the LED light to be
adjusted vertically, and then re-tightened to lock the light into the desired position. A
single stainless steel stud protrudes from the bottom of the mount, enabling the
operator to install the light using a simple through-hole mount.
WIRING
•Power is attached via cord on back of light.
•See wire diagram for connecting power. Red is positive and Black is negative.
•Take appropriate measures for waterproofing connections when installed in an
area prone to getting wet. The LED lamp is IP67 rated waterproof and can
withstand immersion up to 1m.
Mounting Bolt Flying Leads
Adjustment
Screw
-LENS
Amps:2.2 (on 12 volts)
Operating Temp Range: -40°C to +85°C
Waterproof Rating: IP67
Watts: 27 W
Lumens: 2,160
27 Watt Round LED Flood Light 2160 Lumens - Nine 3-Watt LEDs - 10-32 Volt
DC - IP67 Waterproof
LLP-JD-TR-8320
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION
REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT
LARSON ELECTRONICS BY EMAIL AT [e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER
ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.