Larson Electronics LE-4100-6-A User manual

LE-4100-6-A
Remote Control LED Spotlight
12-24V DC, 5000 Lumens - (1) Wireless Remote - 6" Stanchion Mount
Instruction Manual
Thank you for your purchase of the Larson Electronics LE-4100-6-A remote control LED spotlight.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LE-4100-6-A MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOTINSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 3
MOUNTING
The light is mounted on a 6" stanchion post compatible with 2-pin Perko sockets. A
stanchion mount enables the light to be easily installed and removed for storage.
For installation to existing Perko socket, carefully engage stanchion into base
socket. As it slides into socket, make sure the alignment screw at rear of stanchion
slides into notch at rear of socket. Push stanchion down until it engages with
electrical connector at bottom of socket. Lock unit in place by sliding lock collar
into the top of the socket and rotate clockwise. Check to make sure stanchion is
secure in the socket. For installing Perko socket, follow steps page 2.
The LE-4100-6-A from Larson Electronics is a LED Search Light w/ Stanchion
Mount that provides intense output in outdoor locations and is recommended for
lighting support during nighttime operations, emergencies, patrolling, and more.
This LED light operates on 12 V or 24 V DC and provides 5000 Lumens of output
during use. Equipped with a wireless remotes, the LED light with white housing is
compatible with stanchion mounting installations and features a white anchor light.
WARNING: CHECK PRODUCT LABEL FOR CORRECT VOLTAGE!
Verify supply voltage matches product voltage rating as labeled.
SAFETY NOTICE:
◎If replacing LED module, the LED module connector should be connected correctly for positive and
negative wires.
RED and BLUE: Positive (+)
BLACK and BROWN: Negative (-)
◎FCC RULE Part. 15.21：Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
◎This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
◎This searchlight is a Radio Frequency (RF) device which operates on Channel 433.92 MHz. It will send out RF energy
when it is in operation.
1. RF energy may affect some electronic equipment.
2. Some electronic equipment on vehicles or boats may be affected by RF energy.

LE-4100-6-A
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 3
1. For proper light selection, positioning and configuration, refer to A.B.Y.C. Standard A-16*, the '72 COLREGS*,
and the U.S. Inland Rules*.
2. These bases are designed to be mounted on a horizontal surface.
3. For Bi-Color lights, draw a 6" long reference line through the center of the selected mounting location and parallel
to the centerline of the boat.
4. Cut out the mounting template. Place it on the mounting surface such that the reference line (drawn above) is
directly underneath the reference line marked on the template.
5. Drill indicated holes through the template to accommodate #8 oval head mounting screws and socket as required.
6. Attach supply connections to the light, making sure to wire in accordance with both A.B.Y.C. Standard E-9* and
the U.S. Coast Guard Safety Standards for Boat Electrical Systems (33 CFR 183)*.
For 2-contact bases, the supply leads are coded as follows:
WHITE: Positive supply lead
BLACK: Negative supply lead (Caution: Negative lead connected to case. To avoid energizing case, observe
polarity.)
Electrical connections must be made such that the forward compartment is switched in conjunction with the
other running light(s); aft compartment should be switched with Ignition (or permanently energized), as a
push switch is provided on top of the light. NOTE: All light circuits must be circuit protected. Use a 1/2 Amp
fuse (or breaker) for the courtesy light circuit and a 2 Amp fuse (or breaker) for the combination light circuit.
7. Setup for Operation: As pole engages with base, make sure alignment screw in pole slides into the notch in the
base. Push pole until it engages the electrical connector and lock by rotating the locking collar clockwise.
*The above referenced standards can be obtained from
American Boat & Yacht Council, Inc.
613 Third Street, Suite 10
Annapolis, MD 21403
U.S. Coast Guard
Washington D.C. 20593
(or your local C.G. Office)
<< PRINT ACTUAL SIZE (100% SCALE) FOR CORRECT DIMENSIONS.
PERKO SOCKET INSTALLATION

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3of 3
IMPORTANT NOTICE
If searchlight DC power is disconnected (wires disconnected from battery or power supply switched off), after
reconnecting to power, make sure to turn on the searchlight using the wireless or wired remote, to make a full 360°
rotation, in order to reset the home position memory.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
This spotlight is designed to provide years of reliable performance. Should the need for replacement parts arise, please
contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FORWARRANTY AND RETURN INFORMATION.
OPERATION:
1. Press on/off button to Switch on or off searchlight.
Change direction of the light beam by pressing the direction buttons.
2. Utilize the Function button to switch speed
Up
Button Down Button Left Button Right Button
.
Fn
Dual speed (Fast / Slow)
HANDHELD WIRELESS REMOTE PROGRAMMING:
1. Switch off DC Power or disconnect from battery.
2. Make sure there is NO other transmitter operating at the same time.
3. Switch on DC power, within 5 seconds press remote up ▲ and down ▼button
once simultaneously.
4. Searchlight will flash to acknowledge the remote. Connection has been made.
5. Up to 4 remotes may be used with the searchlight (programming a fifth remote
will replace the first). To program a second remote, within five seconds of
programming the first remote, press the second remote’s up and down button
once simultaneously. Repeat to program additional remotes.
NOTE: The included running lights are
always on when mount is receiving power.
The wireless remote control only controls the
search light and NOT the running lights.
LE-4100-6-A