Laser Dollhouse Designs Ariana Victorian Dollhouse User manual

Ariana Victorian Dollhouse Instructions

NOTE 1: Please do a dry assembly using only tape to hold house together. This will get
you familiar with parts, location, and fit. This also gives you a chance to visualize how
you want to approach the build.
Materials for build;
1. Wood glue, you may use Titebond, elmers, tacky or any good wood glue. Tacky
wood glue dries clear.
2. Masking tape to hold house in place during assembly and gluing.
3. Utility knife if needed for trimming.
4. Super glue for small items to seat in place quickly.

Parts for Assembly
Base floor and rails
marked S1 thru S20 Porch stair assemblies
1 small / 2 large set
25 small Outer
window frames
25 small interior
window frames 8 large Outer
window frames
8 large interior
window frames (14 )5.25”1st floor post
(6) 5” 2nd floor post.
1 bag of 11 porch rails and
13 upper porch running
trim
6 octagon
window frames
8 roof gazebo
extensions
3 roof and 1
dormer roof ridge
picket
2 sets of small
side awning
panels
One balcony roof
panel 4th floor side
panel
One dormer set
16 triangle roof
panels (8sm)
(8 Lg)
32 Newel posts

Parts for Assembly
Continued
First floor
Second floor
Third floor
Fourth floor
Fifth floor
Walls 1A thru 1J
Walls 2A thru 2N
Walls 3A thru 3M
Walls 4A thru 4E
Walls 5A thru 5D
3 sets of assembled interior stairs
6 Main roof panels
Upper gazebo roof support
4 GABLES 16 gazebo roof
panel supports
8 large and 8 small
Two gazebo roof
panel support
joiners.
1Lg and 1small
5 Interior working
doors

Assembly
Step 2. Locate porch stair assembly tread and risers along with side supports.
Figure 3. Glue the large and small set riser and treads together as seen in
Figure 4. You should now have two sets of steps and one large and small riser.
Figure 5. On the lower base glue side stair rails into place as seen in Figure 6
and Figure 7.
Figure 1
Step 1. Assemble lower support base by installing rails S1 thru S20 onto base.
Match rail numbers to the base numbers. Figure 1.
If you are NOT doing a dry assembly and have painted parts glue parts to base
and install 1st Floor.
DO NOT GLUE 1st FLOOR TO BASE AS PORCH STAIRS REQUIRE ASSEMBLY. Apply
weight and allow to dry. Figure 2.
Once dry remove 1st floor from base and proceed to step 2.
Figure 3 Figure 4 Figure 5 Figure 7Figure 6

Assembly
Step 2 Continued. Next take the correct length first riser and glue to side rails as seen in Figure 8. Next take the larger tread step and
install by aligning the front notch into the side rails. Make sure that the step is all the way forward. Figure 9. Next install your final steps
for each of the stairs again making sure that the steps is in the rail slot and all the way forward. Figure 10. Next reinstall first floor onto
base. If you are completed with painting and prepping glue in place and add weights to dry. Figure 11.
Figure 8 Figure 9 Figure 10 Figure 11
Step 3. Gather all walls and compete painting and wallpapering as you desire, if not doing a dry assembly. Install outer window frames
to wall by aligning to drawn trace out on wall. Figure 12. Install main doors to walls 1A and 2D. Figure 13. Next turn walls over and install
glass into wall cutouts and install interior window frames to secure glass. Make sure you align interior frame with the outer frame. Look
from each side of the window front and back to double check alignment prior to allowing glue to dry. Finally install interior door frames.
Figure 14. NOTE: DO NOT INSTALL DOORS INTO WALLS 1C, 2C, 3C or 4C.
Figure 12 Figure 13 Figure 14

Assembly
Step 4. Gather walls 1C, 2C, 3C and 4C. Install door frames on both sides of door, figure 15. If you want to install doors request to
purchase at www.laserdoolhouses.com
Once door frames are installed now align and install the stairs to the right side of the wall. Figure 16 DO NOT INSTALL UPPER STAIR
SAFETY RAIL!!
Figure 16Figure 15
Step 5. Install completed walls 1A thru 1J to first floor, figure 17. If you applied glue to the walls make sure not to apply glue to the
upper sides of wall as we will remove the 2nd floor once the first floor walls are dry in place. Install the 2nd floor by aligning upper wall
tabs to slots. Place weight on floor and allow to dry, figure 18. AGAIN DO NOT GLUE 2nd FLOOR TO WALLS!!
Figure 17 Figure 18

Assembly
Step 6. Once first floor walls are dry remove 2nd floor and weights. Figure19.
Step 7. Locate the bag of 11 porch rails and 14 5.25” porch post and install starting from the left side two post and then the porch rail.
Each rail is cut to firmly fit in between the post. Each post should sit through the square cutouts onto the lower frames for the base.
Figure 20. Continue applying a post and then correct fitting rail till you get to the side stairs. Figure 21. Once you reach the side stairs
make sure the last rail is to the inside right of the post as seen in figure 22. This will allow you to install step rail to front of post.
Figure 20
Figure 19 Figure 21 Figure 22
Figure 23
Step 8. Install step rails to front and side porch. Make sure that the post and rails are centered. Figure 23. Once this is completed the
house porch should reflect figure 24. Next install upper stair rail and Newel post at the bottom and top. Again align center to the newel
post the rails and glue in place. Figure 25. Finally install by gluing the second floor to the completed first floor, as you install the floor
make sure to CAREFULLY insert upper post into the cutouts and then proceed to align floor walls. Walls should align as they were glued
earlier fairly easy, figure 26. DO NOT PRESS DOWN HARD ON POST AS THIS WILL BREAK THEM!!!!
Figure 24 Figure 25 Figure 26

Assembly
Step 9. Install the Newel post on the first floor. Figure 27. Next install newel post on the 2nd floor with safety railings.
Step 10. Install all 2nd floor window frames, doors and stairs as done on the 1st floor, Figure 29. Next install all walls 2A thru 2N. Figure 30.
Figure 28
Figure 27 Figure 29 Figure 30
Step 11. Install third floor onto 2nd floor walls and allow the second floor walls to dry. Once dry remove 3rd floor and install newel post to
stairs and then glue 3rd floor to 2nd floor walls as in figure 31. Next install two newel post right above porch rails, figure 32. Locate correct
2nd floor rail and glue to wall at left and first newel post. Rail should fit firm in between. Figure 33. Continue working around installing the
rails and 5” porch post, figure 34, aligned with the first floor post. At the end install a newel post, figure 35.
Figure 31 Figure 32 Figure 33 Figure 34 Figure 35

Assembly
Step 12. Install upper running trim between post. Again they should fit snug. The exception is the last one at the end toward right wall of
gazebo. Figures 36 and 37.
Figure 37Figure 36
Figure 38 Figure 39
Step 13. Install 3rd floor walls by completing as you did for the prior floors. Again DO NOT GLUE 4th floor on. Install the 8 gazebo roof
extensions, figure 38. Next install gazebo roof support onto installed extensions, figure 39. Next locate the smaller 8 roof panel supports
and the smaller center joiner and latch to panel supports to the joiner and install into the gazebo main supports. Figure 40.
Figure 40

Assembly
Step 14. Install remaining panel supports by inserting into the main roof support and then the joiner. Once all are in press panel supports
even into joiner and glue. Figure 41. Next install the smaller roof cap assembly, figure 42. Next locate the 8 smaller roof panels and install
into the open angels as seen in figure 43. Panels should sit flush across to panel supports.
Figure 44
Step 15. Locate front balcony roof panel and support angles, install angles into available cutouts and glue, figure 44. Next install roof
panel. Figure 45. Next repeat the same process for installing the right side roof panel. Figures 46 and 47. Third Floor completed
Figure 45
Figure 42Figure 41 Figure 43
Figure 46 Figure 47

Assembly
Step 18. Install left side roof panel supports behind left tower, figure 52. Next install roof panel, figure 53. Install stair railings on 5th floor
around staircase, figure 54. Install roof rear support wall 5C, figure 55. Next install wall 5C, figure 56.
Step 16. With the gazebo and third floor in now complete installing stairs newel post and then glue 4th floor onto 3rd floor walls as you did
with prior floors, figure 48. Let glue dry. Next install onto 4th floor the left tower by using the larger roof panel supports, center joiner,
and tower cap. Assemble as you did for the gazebo tower roof. Figure 49.
Step 17. Locate and install all window frames, doors, and stairs as done prior for the previous floors and glue. Install 5th floor but again do
not glue 5th floor until completed with stairs. Figure 50. Once dry remove floor and complete newel post install and safety rails. Install 5th
floor by gluing onto 4th floor walls, figure 51.
Figure 49Figure 48 Figure 50 Figure 51
Figure 52 Figure 53 Figure 54 Figure 55 Figure 56

Assembly
Step 19. Install right roof panel onto wall 5C by first inserting into the slot on wall 5B at rear, then the two slots on wall 5C, figure 57. Next
install left roof panel onto wall 5C, figure 58. Install wall 5D make sure the door opens away from staircase, figure 59. Next install wall
5A by inserting into right roof panel on 5C then into the floor. Figure 60. Install left roof panel onto wall 5A and 5B, figure 61.
Figure 58
Figure 57 Figure 59 Figure 60 Figure 61
Step 20. Install right roof panel onto walls 5A and 5B, figure 62. Next install small tier left roof panel onto wall 5A and 5B, figure 63. Next
install dormer support outer walls to right outer roof panel, figure 64. Install dormer outer wall to dormer side walls, figure 65.
Figure 62 Figure 63 Figure 64 Figure 65

Assembly
Figure 69 Figure 70
Step 21. Install dormer roof picket rail. Figure 66. Next install dormer right and left roof panels, figure 67. Finally install dormer gable even
with front edge of roof panels, figure 68.
Figure 67
Figure 66 Figure 68
Step 22. Install remaining roof pickets between three roof tiers, figure 69. Last install remaining Gables to the roof and assembly is
completed.

Congratulations Ariana Dollhouse completed.
Laser Dollhouse Designs.
www.laserdollhouses.com
[email protected]