Laser Dollhouse Designs Kristiana Tudor User manual

Kristiana Tudor Assembly Instructions
By
Laser Dollhouse Designs

Parts for assembly
Second floor base Third floor base First floor base
First floor walls and
porch rails
Second floor walls Third floor walls

Parts for assembly
Porch roof assembly Entry-way roof assembly Etched plexiglas
Porch stair assembly
Interior stairs
Safety rails
Interior walk-way
frames
Top roof frame

Parts for assembly
Base support rails Interior doors, main,
and side doors
Interior window frames
Exterior walls wood siding
Dormer Assemblies

Parts for assembly
Front window roof
assembly Inside front roof frames
Center main roof frame
Outside roof frames
Chimney assemblies

NOTE: Please do a dry assembly using only tape to hold house together. This will get
you familiar with parts, location, and fit. This also give you a chance to visualize how
you want to approach the build.
Materials for build;
1. Wood glue, you may use Titebond, elmers or any good wood glue
2. Masking tape to hold house in place during assembly and gluing.
3. Utility knife for cutting out shingles and forming exterior frames after shingling
roof.

Step 1. Locate base floor and support rails, turn base upside down and insert parts F1,
F3, and F5. See figure 1
Figure 1
Figure 2
Step 2. Install three (3) F4 rails in the middle. Next install rail F2 by inserting into rail F3
and aligning into open groves in rails F4. See figure 2

Step 3.Install the two (2) rail F6 and rails F8 (2), F9 (2), and F10 (2). See figure 3
The base is complete turn right side up.
Figure 3
Figure 4
Step 4. Install interior window frames, when installing place frame on interior side
and align to where you see equal amount of frame on each side when viewing from
the front. Once in place add a small amount of super glue from the front opening
along the frame and window edge. See figure 4

Step 5. Install Interior and exterior doors to walls. Figure 5
Figure 5
Figure 6
Step 6. Install first floor walls by matching walls labeled on tabs to the slots labeled on
the 1st floor. see Figure 6

Step 7. Install first floor stairs before putting on main second floor. Not doing this can
lead to problems installing stairs later. Figure 7
Figure 7
Figure 8
Step 8. Install main second floor above first floor walls by aligning open slots to tabs.
See Figure 8

Step 9. Install safety rails around stairs on second floor. See figure 9
Figure 9
Figure 10
Step 10. Install 2nd floor walls by matching walls labeled on tabs to the slots labeled on
the 2nd floor base. See Figure 10

Figure 11
Figure 12
Step 12. Install 3rd floor matching wall tabs to the floor slots. See Figure 12
Step 11. Install 2nd floor stairs before putting on third floor. Not doing this can lead to
problems installing stairs later. See figure 11

Figure 13
Figure 14
Step 14. Install interior frames to 3rd floor walls and arched door frames. Install 3rd
floor walls. See Figure 14
Step 13. Install 3rd floor safety rails. See figure 13

Figure 15
Figure 16
Step 16. Install right interior front roof panel. Make sure you seat the front panel and
middle roof panel flush together. See Figure 16
Step 15. Install center roof panel. See figure 15

Figure 17
Figure 18
Step 18. Install front window plexiglas
into wall opening, install outer wall
frames. See Figure 18
Step 17. repeat step 16 for the left side.
See figure 17

Figure 19
Figure 20
Step 20. Repeat set 19 for the left side. See
Figure 20
Step 19. Install right gable and outer main
roof panel. See figure 19

Figure 21
Figure 22
Step 22. Install outer dormer support frames
for right and left side dormer. See Figure 22
Step 21. Install upper roof center panel
with tab listed back to the rear of house.
Panel should be flush at all corners. See
figure 21

Figure 23
Figure 24
Step 24. Install dormer roof frames. See
Figure 24
Step 23. Install dormer face. See figure 23

Figure 25
Figure 26
Step 26. Install entry roof panel. See
Figure 26
Step 25. Install entry roof supports. See
figure 25

Figure 27
Figure 28
Step 28. Install window center roof
panel. See Figure 28
Step 27. Install window center roof support
to top of lower window extension panels.
See figure 27