Laser Dollhouse Designs Little Ann Assembly Instruction User manual

The Little Ann Assembly Instruction
By Laser Dollhouse Designs

Parts for assembly
Door Assembly
Roof Assembly
Subfloor
Assembly
S1 thru S4
2nd Floor
Assembly
2A, 2B & Fretwork
1st and 2nd Floors
Fence
Assembly
Window
Frames
Plexiglas
1st Floor
Walls
1A , 1E, & 1F
Porch rails
1A, 1B & 1C
Stairs
Base Floor

Step 1. locate the Base floor and position as seen in Figure 1
Figure 1
Step 2. Locate Subfloor Assembly S1 thru S4 and
insert S1 thru S4 tabs into Base floor matching Slots
S1-S4 as seen in Figure 2
Figure 2

Step 3. Take the First floor marked 1A thru 1F and insert on top of assembled subfloor
by aligning open slots to tabs. Refer to figure 3.
Figure 2
Figure 3
Step 4. Take 1A Wall and insert into slot 1A on first floor.
Then insert door assembly thru cutout for the door
opening. Refer to figure 4 and 5.
Figure 4 Figure 5

Step 5. Take the two rectangle and one half circle Plexiglas
cutouts and insert into openings from the interior side
of wall. Finally secure by placing the interior door
frame in place. Refer to figure 6, 7 and 8.
Figure 7
Figure 6
Figure 8

Step 6. Take the porch rail 1A, 1B and 1C and insert into
slots 1A-1C. Also place walls 1E and 1F into respective
slots on first floor. Refer to figure 9.
Figure 9

Step 7. Place window frame on exterior of walls 1E and 1F
Refer to figure 10.
Figure 10
Step 8. Place window Plexiglas cutouts into cutouts of
walls 1E and 1F from the interior side and then place
interior frames to secure. See figures 11 and 12.
Figure11 Figure12

Step 9. Secure first floor by inserting second floor on top
and aligning cutout tabs to slots on top of first floor
rails and walls. See figures 13
Figure13
Step 10. Place second floor walls 2A and 2b into slots
provided. Refer to figure 14
Figure14
Step 11. Place window frame and Plexiglas into 2A as done
with walls 1E and 1F. See figure 15
Figure15

Step 12. Align and place one side of the roof making sure
the cut slots closest to the top are up as in figure 16
Note: Two front cutout,
The most forward cutouts closest to the top is right side up
facing.
Figure16
Step 13. Place fretwork into roof by matching tabs
and slots. See figure 17
Figure17

Step 14. Now add the other side of the roof by
matching the tabs and slots. Refer to figure 18
Figure18
Step 15. Locate the post as seen in figure 19. This
post fits to the front right forward corner. Place
fence rail as seen in figure 20 into the side of post
and into base. Once in place should be as in
figure 21
Figure19
Figure20 Figure21

Step 16. Locate the fence rail as seen in figure 22 and add to opening in post. Next
locate post as seen in figure 23 and insert fence and post to base. The circle to hold
functioning gate should be at bottom.
Figure22 Figure23
Step 17. Locate final fence rail with swing gate along with remaining side fence and insert into
base as seen in figure 24
Figure24

Step 18. Take stairs assembly and place within fence as seen in figure 25
Figure25
Step 19. Install shingles to house. Shingles align first
set to bottom of roof panel. Next shingle aligns to
the top line of lower shingles as seen in figure 26.
Figure26

Laser Dollhouse Designs
www.laserdollhouses.com
Email: [e-mail]