Laser Dollhouse Designs Glenrose User manual

The Glenrose assembly Instructions
By Laser Dollhouse Designs

Parts
Subfloor walls marked S1-S5,
S6(x3)
Porch Stair assemblies Base marked S1-S6
First Floor marked
1A-1J
Plexiglas inserts
First Floor walls and rails
1A thru 1J
Second Floor marked 2A-2D
Front and rear roof
Second Floor walls 2A-2D

Parts continued
First floor porch rails
Door assemblies 3-interior / 1 Main
Dormer assembly kit x 3
Chimney kits
Window Frames

Parts continued (spiral stairs)

Parts continued (spiral stairs)
18 Handrails 18 Treads
17 Risers double notch 1 lower Risers (larger of two)
1 Upper Riser (Smaller of two)
1 assembly support
1 center
support rail

Base Floor assembly : (Note; recommend doing a dry assembly prior to gluing. This way
you are familiar with the way parts go together.)
Step 1. Match subfloor parts to base. S1 walls to S1 marked slots on base.
continue till S1 thru S6 are fitted into the base slots should look like figure 1.
figure 1
figure 2
Step 2. Install first floor on to assembled base.
Figure 2.

Step 3. Take the assembly support and lay on a flat surface. Next
insert the dowel into the center hole. DO NOT GLUE THESE
TOGETHER!!! see in figure 3 This will help keep the stairs level
during assembly. Once assembly is done the assembly support
will be removed and the spiral stairs inserted into the house.
Figure 3
Step 4. Using the lower riser (the bottom part and larger of the
two) Figure 4, and a tread Figure 5, glue to the left side as
seen in figure 6. Make sure the tread circle angle is to the
left when the round hole is facing up. See note below. Figure 4
Figure 5 Figure 6
Note: Tread facing
up and notch to the
left, riser glued to
the bottom left side.

Step 5. Using the remaining risers with two tabs (figure 7) and
remaining treads glue them together with the risers on the
bottom left side. Figure 8 You should have when done 17
assemblies with risers having a bottom tab and one
without a tab along with the upper final. Figure 9
Figure 7
Figure 8
Figure 9

Step 6. Place the center support dowel into the holder, take
the step assembly with no bottom tab and insert from the
top (figure 10) of the dowel and slide down to the bottom.
Make sure dowel is straight up and down and step
assembly is flush to the bottom. Figure 11 Using superglue,
glue step ring to dowel. DO NOT GLUE THE SUPPORT AS IT
IS NOT PART OF THE STAIRS!!!
Figure 10
Figure 11
GLUE!!!

Step 7. Run superglue along the outer edge where handrail
will be placed (figure 12) and install handrail. Figure 13
Figure 12
Figure 13
GLUE!!!

Step 8. Run superglue along the right edge of your first
assembled step. Figure 14 Next take one of the 17
assembled steps with a tab (figure 15) and insert on dowel
and slide down and join to the lower step. Figure 16. Make
sure that the front riser meets up with the lower steps
handrail. You may have a small gap in the cutout middle of
the step. This is fine as it is more important that the riser
and rail align in order to meet the next step assembly.
Figure 15
Figure 14
GLUE!!!
Figure 16
Should meet up together!!!

Step 9. Repeat steps 7 and 8 until you reach the at this point
remove the stairs from the assembly support circle and install
last single riser. Figures 17. Spiral stairs are now ready for
inserting into house.
Figure 17
Figure 18
Step 10. Install outer window frames to all external
walls. Turn wall and look from the interior side to align
frame evenly. Figure 18.

Step 11. Install plexiglas into cutout of wall. Figure 19.
NOTE: if gluing frames in remove protective plastic cover on
plexiglas.
Figure 19
Step 12. Install interior window frames. Figure 20.
Figure 20

Step 13. Install first floor chimney assembly to wall 1i
and 2nd floor chimney assembly to wall 2C. Figure 21.
Figure 21
Figure 22
Step 14. Install first walls and rails to assembled
base. Figure 22.

Step 15. Install first floor main door and interior
door. Install door frames. Figure 23.
Figure 23
Figure 24
Step 16. Install spiral stairs into circle cutout on
first floor. Figure 24.
Figure 25
Step 17. Install 2nd floor base by aligning all 1st
floor upper tabs to open slots. Be careful with
stair rails. Once in place align upper spiral stair
riser to leading edge opening to 2nd floor. Figure
25.

Figure 26
Step 18. Install 2nd floor wall marked 2A-2D. Install
doors and interior door frames. Figure 26.
Figure 27
Step 19. Install safety rails around stair opening as
seen in figure 27.

Step 20. Install rear roof panel figure 28.
Figure 30
Step 21. Install chimney to rear roof panel figure 29.
Figure 28
Figure 29
Step 22. Install front roof panel, figure 30.

Step 23. Install dormers to front roof panel.
Step 24. Install porch stairs. Assembly completed.

Laser Dollhouse Designs
www.laserdollhouses.com
Email: laser[email protected]