Laser Dollhouse Designs Tiffany Victorian User manual

Tiffany Victorian assembly instructions
By
Laser Dollhouse Designs

Tiffany Victorian Parts
First Floor base Second Floor base Third Floor base French
Door (1)
Oval door
frames (2)
Half oval(2) Interior doors (5)
Exterior doors (2) Straight stairs (2)
Unassembled
Subfloor support rails
Interior/ exterior walls
First floor 1A thru 1M
Second Floor 2A thru 2N
Third Floor 3A thru 3E
Porch frames and
rails
Porch Posts
15- long
3-short
Alcove roof panels
Main roof panels
Window Frames
Front porch
stair assembly
Interior stair safety
rails
(comes unassembled)
Set of two long and
one short
13 spindles, 6 rails
Shingles
Alcove
roof trim
Main roof trim

NOTE: Please do a dry assembly using only tape to hold house together. This will get
you familiar with parts, location, and fit. This also give you a chance to visualize how
you want to approach the build.
Materials for build;
1. Wood glue, you may use Titebond, elmers or any good wood glue
2. Masking tape to hold house in place during assembly and gluing.
3. Utility knife for cutting out shingles and forming exterior frames after shingling
roof.
4. 200-300 grit sandpaper
5. Alcohol for cleaning laser burn areas and post (optional)
6. Your choice of paint, recommend spray paint and a spray sealer for small items.

NOTE: Please do a dry assembly using only tape to hold house together. This will get
you familiar with parts, location, and fit. This also give you a chance to visualize how
you want to approach the build. Instructions cover basic assembly not when to paint,
stain, or glue as this depends on you build and what you are adding. THIS IS WHY IT IS
IMPORTANT TO DO A DRY ASSEMBLY!!! Once dry assembly completed prep, paint,
wallpaper and stain all items for assembly and glue in place.
Step 1. Locate base floor and support rails, turn base upside down and insert support
rail skirts. See figure 1
Figure 1
Figure 2
Step 2. (SKIP STEP IF DRY ASSEMBLING)
Install interior window frames, when installing place
frame on interior side and align to where you see
equal amount of frame on each side when viewing
from the front. Once in place add a small amount of
super glue from the front opening along the frame
and window edge. See figure 2

Step 3. Install Interior and exterior doors to walls and frames. See figure 3
ONLY GLUE IN FINAL ASSEMBLY.
Figure 3
Figure 4
Step 4. Install walls 1A thru 1M to assembled first floor
base. See figure 4.

Step 5. Install second floor on to the first floor walls. Figure 5
Figure 5
Figure 6
Step 6. Stairs assembly, locate stair case. The bottom
riser (step) is the side with the ¼ “ square dowel.
Figure 6
Bottom
Top

Step 7. Install tread to each step. For this house we will have
our handrail on the right side. Make sure to glue in place with
the square cutouts to the right for your spindles. Figure 7
Figure 7
Figure 8
Step 8. Install the spindles with the slop facing back.
As in Figure 8. seat the spindles firmly within the
square cutouts. They should seat to the first bottom
grove in the spindle.

Step 9. with spindles installed, now glue to the front riser a
newel post. Make sure post is aligned to the outside of the first
riser and the spindles are centered. Figure 9
Figure 9
Figure 10
Step 10. Install the handrail. First glue to lower
newel post, view rail angle to spindles and
starting from the bottom glue each spindle to
rail. Adjust to rail angle. (Do not push rail to
spindle as this will result in your rail not being
straight.) Adjust spindle angle by prushing fwd
or back to change angle. Figure 10

Step 11. Glue top Newel post to front of handrail and top
tread. Figure 11 repeat steps for second floor stairs. Paint
and let dry.
Figure 11
Figure 12
Step 12. assemble side long safety stair rails
(x2), using 5 spindles evenly spaced along the
rail and mark. Next glue to handrail. Figures 12
and 13.
Figure 13

Step 13. install top handrail making sure it aligns to
bottom rail. Figure 14. repeat steps for second set for third
floor.
Figure 14
Figure 15
Step 14. Using 3 spindles repeat steps to
assemble as you did earlier. Figure 15 you
should now have one short and two long sets
of safety rails
Figure 16
Step 15. Install 3 newel post forming an L
shape with the small run to the left (third
Floors) and 2 newel post forming one rail
for the second floor. See figure 16, paint
and let dry.