Laserworld PRO-500G MH User manual

PRO-500G MH
USER MANUAL

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
2
of
4
Please read this manual carefully before use!
I
Table of contents
Page
. SAFETY INSTRUCTIONS 3
2. OPERATING DETERMINATIONS 4
3. OPEN THE BOX FOR CHECKING 5
4. SAFETY INSTRUCTIONS 5
5. ATTENTION 6
6. WARNING 6
7. DESCRIPTION OF THE DEVICE 7
8. CONNECTION TO THE MAINS 8
9. CONTROL BOARD OPERATION 9
0. DMX5 2 OPERATE 0
. MAINTENANCE
2. TECHNICAL SPECIFICATIONS
3. ELECTRICAL DIAGRAM 2

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
3
of
4
hecking Parts
Please check if the following parts are included:
x Laser projector
x Power cable
x User manual
Safety instructions
If the device has been exposed to great temperature changes, do not switch it on
immediately. Condensation water may damage your device. Leave the device
switched off until it has reached room temperature.
The laser must only be used for shows. Any operation has to be attended and
supervised by a skilled and well-trained operator.
Never leave this device running unattended and keep it away from children and
unauthorized persons.
Keep away from heaters and other heat sources. In order to safeguard sufficient
ventilation, leave 50 cm of free space around the device.
Never direct the laser beam to people or animals.
CAUTION LASER DIODE: If you open the device for cleaning, always disconnect from
mains!
-HEALTH HAZARD! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock!
These lasers are considered a definite eye hazard, particularly at the
higher power levels, which WILL cause eye damage. So these laser
series models supplied with a key switch to prevent unauthorized use,
warning labels and aperture labels affixed to the laser.
Installation safety
Prior to installation and operation of the laser, the paths of the beams and
effects should be considered, particularly with respect to how they will reach
the audience. If direct audience scanning is desired, then the laser energy in
the effects needs to be considered to decide if the effects are safe for direct viewing. Always
ensure, that the maximum permissible exposure (MPE) is not exceeded in the area accesible
to the public. So install the laser in such a way, that minimum distances and heights ensure
the MPE is never exceeded in the public area.
Warning labels on the device
Laser radiation Read manual
before use
Avoid exposure Operation by qualified
To the beam personal only
Laser class 3b Never direct laser
Beam at people
Caution of radiation Never look directly
If cover is removed into beam
Indoor use only
At front opening: Avoid exposure – laser radiation is emmited.

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
4
of
4
OPERATING THE LASER
The operator has to make sure that laser radiation – also reflected laser radiation – higher
than the maximum permissible level is avoided by technical or organisational measures.
(Especially with respect to the MPE, see above.)
Make sure to use the correct voltage
If the device is used in a flying installation, the mounting brackets and an appropriate safety-
rope must be fixed.
In some countries, the operator must notify the accidence insurance and the authority for
industrial safety, before operating a laser. For more information, contact the relevant
authorities.
Please consider that unauthorized modifications on the device are strictly forbidden due to
safety reasons!
If this device will be operated in any way differently than described in this manual, the
product may suffer damages and the guarantee becomes void. Furthermore, any other
operation may lead to dangers like short-circuit, burns, electric shock, etc.
Keep surrounding dry and clean. This unit should be keep dry, do not use in the rain or
damp and dusty environment. Projector should be put in a water-proof housing when
operated outside.
Regularly open the device (see “cleaning” further down) to check for dust inside, or if fog
fluid condenses in the housing (if so rearrange hazer and/or laser position).
Operating temperature is 0~35°C. In a new installation, check after some 5-30 minutes
whether the outlet air gets too warm. Regularly check the inside for dust deposits, especially
around the fans. Let laser cool off 0minutes after 2 hours of operation,to ensure maximum
lifetime for the diode.
Distance between laser aperture and projection screen should be not less than meter.
Do not turn device on and immediately off again frequently.
Do not look into the laser beam directly, especially not with optical instruments.
Do not touch the device with wet hands.
When the laser diode becomes dim or broken, please contact your dealer timely.
When returning laser to dealer/manufacturer always use original packaging.
Maintenance should be performed every 5-day period. See “cleaning” further down.
Using the laser
aution – use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
5
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
6
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
7
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
8
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
9
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
0
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
of
4
6. MAINTENAN E
Maintenance should be performed every 5-day period, by using a sponge which is
dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the
mirror.
Always disconnect from the mains when the device is not in use or before cleaning it.
There are no serviceable parts inside the device. Maintenance and service operations
are only to be carried out by authorized dealers.
Never look directly into the light source.
Always disconnect from the mains when the device is not in use or before
cleaning it.
7. TE HNI AL SPE IFI ATIONS
Power supply: AC 00V- 20V or 220V-240V, both at 50/60 Hz
DMX 512: 6 channels
ondition temperature: - 0°C ~ +35°C
Input signal bandwidth: 0~ 000Hz
X/Y axes beam scanning optical angle: 0 ~ ±30°
Signal input power: -5V~+5V
Power consumption: 05 W
Working mode: ILDA, DMX5 2, automatic mode (sound, stand-alone programmes)
Optical power: Green: >250mW, max 500mW
Laser classification: 3b
Weight: 30 kg
Dimensions: 459 x 479 x 639 mm (L x W x H)
PLEASE NOTE
This device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user
to follow the safety instructions and warning notes written in this user manual.
Laserworld cannot be made liable for damages caused by incorrect installations and
unskilled operation!
For service contact your dealer, or Laserworld.

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
2
of
4

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
3
of
4
EU- Declaration of onformity
We hereby confirm that the following device
complies with the essential safety requirements, laid down in the regulations of the
committee to assimilate the provisions of law of all participating EU states on the
electromagnetic compatibility (89/336/EWG) and with the requirements relating to the Low
Voltage Directive (LVD 2006/95/EG) was based on the following standards:
DIN EN 6 000-3-2:2000 + A2: 2005
DIN EN 6 000-3-3: 995 + A : 200
Furthermore, the device is verified in correspondence to the laser class regulations DIN EN
60825- , if properly set up according to the upper mentioned laser safety regulation.
After installing the device, an inspection and official approval is indispensable for the overall
setup. The inspection must follow the European guidelines EN 60825- /-3 and corresponding
regulations for the prevention of accidents BGV-B2.
This declaration is executed on behalf of the manufacturer.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil-Oberhofen
SWITZERLAND
Authorized person:
Supervisory board Mr Martin Werner
place of business: 8574 Lengwil / SWITZERLAND
company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
www.laserworld.com
[e-mail]
representative according to EMVG:
Cleantech Europe GmbH
Managing Director: Thomas Schulze
Fürkhofstr. 5
8 927 München / DE

USER MANUAL: Laserworld Moving Head PRO-500G MH
Rev: 02/20 0
Page
4
of
4