Leadshine Technology 3DM2283 User manual

User Manual
3DM2283
3-Phase Digital Stepper Drive
©2019 China Leadshine Technology Co., Ltd.
Address: 15-20/F, Block B, Nanshan I Valley, No.3185, Shahe West Road, Nanshan District, Shenzhen,
Guangdong, 518055, China
Tel: [phone] Fax: [phone]
Web: www.leadshine.com Sales: [e-mail]
Support: [e-mail]

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 2of 7
3DM2283 3-phase Digital Stepper Drive
150-220VAC, 0.5-8.2A peak, Auto-configuration, Low Noise
Anti-Resonance provides optimal torque and nulls mid-range instability
Motor auto-identification and parameter auto-configuration technology, offers optimal
responses with different motors
Multi-Stepping allows a low resolution step input to produce a higher microstep output, thus
offers smoother motor movement
Microstep resolutions from full-step to51,200.
Soft-start with no “jump” when powered on
Supply voltage up to +220 VAC
Output current programmable, from 0.5A to 11.7A. It can also be set via DIP switches.
Pulse input frequency up to 200 KHz
5V optically isolated input
Automatic idle-current reduction (Reduction rate can be software configured)
Suitable for 3-phase motors
Support PUL/DIR and CW/CCW modes
Over-voltage, over-current protections
Descriptions
The 3DM2283 is a high voltage, fully digital stepper drive developed with advanced DSP control algorithm based on the latest motion
control technology. It has achieved a unique level of system smoothness, providing optimal torque and nulls mid-range instability. Its
motor auto-identification and parameter auto-configuration feature offers quick setup to optimal modes with different motors. Compared
with traditional analog drives, 3DM2283 can drive a stepper motor at much lower noise, lower heating, and smoother movement. Its
unique features make 3DM2283 an ideal choice for high requirement applications.
Applications
Suitable for a wide range of stepper motors, from NEMA size 34 to 51. It can be used in various applications such as laser cutters, laser
markers, high precision X-Y tables, labeling machines, CNC router, etc. Its unique features make the 3DM2283 an ideal choice for
applications that require both low-speed smoothness and high speed performances

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 3of 7
Specifications
Electrical Specifications
Parameter
Min
Typical
Max
Unit
Input Voltage
150
220
240
VAC
Pulse Input Frequency
0
-
200
kHz
Logic Signal Current
7
10
16
mA
Isolation Resistance
500
-
-
MΩ
Operating Environment
Cooling
Natural Cooling or Forced cooling
Operating Environment
Environment
Avoid dust, oil fog and corrosive
gases
Storage Temperature
-20℃ － 65℃(-4℉ － 149℉)
Ambient Temperature
0℃－50℃(32℉ － 122℉)
Humidity
40%RH －90%RH
Operating Temperature (Heat
Sink)
70℃(158℉) Max
Storage Temperature
-20℃－65℃(-4℉ － 149℉)
Weight
1.3Kg (2.87lbs)
Mechanical Specifications

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 4of 7
Protection Indications
The green indicator turns on at power-up. When drive protection is activated, the red LED blinks periodicity to indicate the error type
Priority
Time(s) of Blink
Sequence wave of RED LED
Description
1st
1
0.2S
3S
Over-current Protection
2nd
2
0.2S 0.3S
3S
Over-voltage Protection，over 440VDC
Pin Assignment
The 3DM2283 has one barrier strip connector for power and motor connections and one screw terminal for control signal connections.
Power and Motor Connector
Pin
Name
I/O
Description
1
PE
-
Recommend connect this port to the ground for better safety.
2
L
I
Power supply inputs. If AC input, recommend use isolation transformers with
theoretical output voltage of 150-220VAC.
3
N
I
4
NC
-
No Connection
5
U
O
Motor Phase U
6
V
O
Motor Phase V
7
W
O
Motor Phase W
Pin Assignment (Continued)
Control Signal Connector
Pin
Name
I/O
Description
1
PUL+
I
Pulse Signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each
rising or falling edge active (software configurable, see DM drives software operational
manual for the detail); In double pulse mode (software configurable), this input represents
clockwise (CW) pulse, active both at high level and low level. 4-5V when PUL-HIGH,
0-0.5V when PUL-LOW. For reliable response, pulse width should be longer than 2.5μs.
Series connect resistors for current-limiting when +12V or +24V used. The same as DIR
and ENA signal.
2
PUL-
I
3
DIR+
I
Direction Signal: In single-pulse mode, this signal has low/high voltage levels, representing
two directions of motor rotation. In double-pulse mode (software configurable), this signal
is counter-clock (CCW) pulse, active both at high level and low level. For reliable motion

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 5of 7
response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,
0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-driver
wiring match. Exchanging the connection of two wires for a coil to the driver will reverse
motion direction. The direction signal’s polarity is software configurable.
4
DIR-
I
5
ENA+
I
Enable signal: This signal is used for enabling/disabling the drive. In default, high level
(NPN control signal) for enabling the driver and low level for disabling the driver. Usually
left UNCONNECTED (ENABLED). Please note that PNP and Differential control signals
are on the contrary, namely Low level for enabling. The active level of ENA signal is
software configurable.
6
ENA-
I
7
FAULT+
O
Fault Signal: OC output signal, active when one of the following protection is activated:
over-voltage, over current, low voltage, phase error and over-temperature. This port can
sink or source 20mA current at 24V. In default, the resistance between FAULT+ and
FAULT- is high impedance in normal operation and become low when 3DM2283 goes into
error.
8
FAULT-
O
RS232 Communication Port
The RS232 communication port is used to configure the 3DM2283’s peak current, microstep, active level, current loop parameters and
anti-resonance parameters. See DM driver’s software operational manual for more information.
RS232 Communication Port
Pin
Name
I/O
Description
1
NC
-
Not connected.
2
+5V
O
Not connected.
3
TxD
O
RS232 transmit.
4
GND
GND
Ground.
5
RxD
I
RS232 receive.
6
NC
-
Not connected.
DIP Switch Settings
Dynamic Current
Peak
RMS
SW1
SW2
SW3
Default
Default
OFF
OFF
OFF
3.1A
2.2A
ON
OFF
OFF
4.5A
3.2A
OFF
ON
OFF
5.9A
4.2A
ON
ON
OFF
7.3A
5.2A
OFF
OFF
ON
8.9A
6.3A
ON
OFF
ON
10.1A
7.2A
OFF
ON
ON
11.7A
8.3A
ON
ON
ON

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 6of 7
Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly under high speed condition.
Idle-Current
SW4 determines whether current-reduction is performed when there is no pulse applied to 3DM2283..
OFF
ON
SW4
Motor current reduces automatically when
there is no pulse applied to 3DM2283.
Motor current is the same as the dynamic
current when there is no pulse applied to
3DM2283.
Microstep Resolution
Steps/Revolution
SW5
SW6
SW7
SW8
200
ON
ON
ON
ON
400
OFF
ON
ON
ON
1600
ON
OFF
ON
ON
3200
OFF
OFF
ON
ON
6400
ON
ON
OFF
ON
12800
OFF
ON
OFF
ON
25600
ON
OFF
OFF
ON
500
OFF
OFF
OFF
ON
1000
ON
ON
ON
OFF
1200
OFF
ON
ON
OFF
2000
ON
OFF
ON
OFF
4000
OFF
OFF
ON
OFF
5000
ON
ON
OFF
OFF
6000
OFF
ON
OFF
OFF
8000
ON
OFF
OFF
OFF
10000
OFF
OFF
OFF
OFF
Auto-Configuration
Switch SW4 two times in two seconds will activate parameter Auto-configuration for 3DM2283’s current loop. That is, OFF-ON-OFF or
ON-OFF-ON. During Auto-configuration, motor parameters are identified and 3DM2283’s current loop parameters are calculated
automatically. The motor shaft will vibrate a little during the process of Auto-configuration which takes about 1 to 3 seconds.

High Voltage Digital Stepper Drive 3DM2283 Manual
Page 7of 7
Typical Connections
NPN Control Signal
3DM2283 Drive
DIR+
Controller
VCC
PUL-
150 ~ 220 VAC
L
N
U
V
W
270O
270O
270O
PUL+
ENA-
R=0 if VCC=5V;
R=1K(Power>0.125W) if VCC=12V;
R=2K(Power>0.125W) if VCC=24V;
R must be connected to control signal terminal.
R
R
R
PUL
DIR
ENABLE
DIR-
ENA+
FAULT-
FAULT+
PE
FAULT
M
~ AC Input
863SXX
YEL WHT
BRN
BLK RED
BLU