Legacy Classic Furniture 7200-5005 User manual

ASSEMBLY INSTRUCTIONS:
Caution: (1) These parts are cumbersome a d heavy. This product ca best be assembled with the
assista ce of o e or more perso s i order to preve t perso al i jury a d to i sure parts are ot damaged
duri g the assembly process. If dirty, clea fi ished parts with mild dishwashi g liquid a d water solutio
applied o damp cloth. Cloth should ot be excessively wet. Polish fi ish with soft cloth a d a i dustry
recog ized fur iture polish.
(2) To preve t damage to your floor or carpet, please check the bottom of each piece of fur iture
for stai residue a d rough surfaces a d also check for staples or ails left after removi g the packagi g
material. The ma ufacturer will ot be held respo sible if preve tative steps are ot take prior to
i stallatio .
(3) Duri g ormal use everyday, screws, bolts, uts a d woode plugs may loose up. They
should be periodically i spected a d re-tighte ed to preve t damage to the fur iture a d (or) perso al
property or cause i jury. Always check to be sure all hardware o this list a d the below me tio ed
compo e ts are attached to the fur iture properly a d kept tighte ed.
Tha k you for purchasi g this quality product. Before begi i g, please check the packi g material carefully
for small parts which may have come loose i side the carto duri g shippi g. Please do ot discard a y
packi g material u til all parts have bee located. If a y parts are missi g, please co tact your dealer for
prompt replaceme t.
Parts & Hardware List:
www.legacyclassic.com
LEGACY CLASSIC
FURNITURE
PARTS LIST Q'TY
1 PC
B
HEADBOARD
2 PCS
C
FOOTBOARD 1 PC
BED RAIL
A
4 PCS
D
HARDWARE LIST
LONG BOLT
1
Q'TY
8 PCS
2 8 PCS
38 PCS
4LARGE HEX
WRENCH 1 PC
LARGER LOCK
WASHER
5/16"*25mm
5/16"
5/16"*19*2mm
LARGER FLAT
WASHER
Step 2
CANOPY RAIL
7200-5005 METAL BED QUEEN 5/0
70*30*5mm
CANOPY CENTER
SLAT RAIL
SUPPORT LEG
1 PC
E
3 PCS
F
3 PCS
G
NICKEL BOLT
SMALL HEX
WRENCH
SMALL LOCK
WASHER
SMALL FLAT
WASHER
5
6
6 PCS
7
6 PCS
8
6 PCS
9
1 PC
1/4"*15mm
1/4"
1/4"
70*30*4mm
Step 3
SHORT BOLT
8 PCS
1/4"*15mm
FINIAL 4 PCS
H
HEADBOARD POST 2 PCS
I
FOOTBOARD POST 2 PCS
J
E
D
D
D
D
C
C
A
B
4
1
2
3
9
8

ASSEMBLY INSTRUCTIONS:
www.legacyclassic.com
LEGACY CLASSIC
FURNITURE
Assembly Procedures:
Step 1: Lay o t all parts and hardware. Make s re the q antity of each is correct and the feet are free of stain,
staples, screws and nails.
Step 2: Assemble the canopy rails (D) to the canopy center (E) sing hardware (9, 8) as shown.
Step 3: Assemble the headboard (A) and footboard (B) to the bed rail (C) sing hardware (1, 2, 3, 4) as
shown.
Step 4: Assemble the post (I & J) to the headboard & footboard (A & B) as shown.
Step 5: Place the entire canopy on top of the posts sing final (H) attached as shown. Then assemble the
s pport leg (G) to the slat rail (F), then p t the slat rails (F) on the bed rails and assemble them sing
hardware (5, 6, 7, 8) as shown. The s pport leg leveler needs to to ch the floor to s pport the slats
and mattress.
Note: High/low option, canopy and posts can be removed. Assemble the finial to the headboard/footboard.
Assembly is complete.
7200-5005 METAL BED QUEEN 5/0
Step 4 Step 5
F
G
I
IJ
J
H
H
H
H
5
6
7
8
G
F