Legacy Classic Furniture 9814-8110 User manual

ASSEMBLY INSTRUCTIONS
Congratulations on your purchase of a Legacy Classic Kids Bed.
Every effort has been made to ensure your furniture is of the
finest quality. If you find that your furniture has a missing or
damaged part, please contact your local Legacy Classic retailer.
Please read and follow these instructions carefully.
Model No .
Page 1
www. legacyclassic. com

READ THESE INSTRUCTIONS CAREFULLY
BEFORE ATTEMPTING TO ASSEMBLE THIS BED.
Carton #1 (8130)
Wood Hole cover (4pcs)
BED ENDS (4pcs)
Carton #2 (8120) Carton #3 (8110)
SIDE RAIL (4pcs) SLAT ROLLS (2 SETS)
LADDER (1 PC)
GUARD RAIL (2 PCS)
Page 2
SAFETY WARNINGS AND GENERAL NOTES:
Lay out all parts and hardware on a clean protective surface to protect the furniture and floor during assembly. Make sure
the quantity of each is correct and the feet are free of stain, staples, screws and nails.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the assistance of one or more
persons in order to prevent personal injury and to insure parts are not damaged during the assembly process. If dirty, clean
finished parts with mild dishwashing liquid and water solution applied on damp cloth. Cloth should not be excessively wet.
Polish finish with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residue and
rough surfaces and also check for staples or nails left after removing the packaging material . The manufacturer will not be held
responsible if preventative steps are not taken prior to installation.
(3) During normal use everyday, screws , bolts, nuts and wooden plugs may loosen up. They should be periodically
inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure
all hardware on this list and the below mentioned components are attached to the furniture properly and kept tightened.

Page 3
ID #
A
ID #
B
ID #
C
ID #
F
Qty
16
ID #
G
Qty
4
ID #
K
Qty
10
ID #
L
Qty
1
Qty
1
Qty
16
Qty
16
Phillip Head Screwdriver
Standard Head Screwdriver
occupy.
. The assembly will require at the least two
people to complete.
ID #
D
Qty
6
ID #
M
Qty
16
ID #
E
Qty
16

Page 4
ID #
A
Qty
16
A

Page 5
ID #
BC
ID # Qty
1 16
Qty
BE
M
ID #
EM
ID # Qty
16 16
Qty

Page 6
ID #
F
Qty
16
ID #
G
Qty
4
F

Page 7
ID #
K
Qty
8
ID #
D
Qty
6
ID #
L
Qty
1
L
K

Page 8
ID #
K
Qty
2

Page 9
M A T T R E S S S I Z E S
For Twin size: Use only mattress which is 74 1
2'' - 75 1 2'' long and
37 1
2'' - 38 1 2'' wide on upper bunk and lower bunk.
Maximum Foundation & Mattress Thickness Combined: (10")
For Full size:Use only mattress which is 74 1
2'' - 75 1 2'' long and
52 1
2'' - 53 1 2'' wide on upper bunk and lower bunk.
Maximum Foundation & Mattress Thickness Combined: (10")
B E D D I N G S P E C I F I C A T I O N
SLAT ROLL
Maximum
Distance
10 inches
5"
(MINIMUM DISTANCE
FROM TOP OF GUARD
RAIL TO TOP OF
MATTRESS )
MATTRESS
GUARD RAIL
SIDE RAIL