Legacy Classic Furniture QUEEN 5/0 8460-4105 User manual

PART QTY PART DIAGRAM DESCRIPTION QTY
1
Wrench 1 PC
2
Hexigon Bolt
1/4" x 2-1/2" 6 PCS
3
Hexigon Bolt
1/4" x 1-3/4" 4 PCS
4
Spring Washer
1/4"*11*2mm
10 PCS
5
Flat Washer
1/4"*18*2mm
10 PCS
6
Screw
Ø8*30mm 6 PCS
7
Wrench 1 PC
8
Hexagonal Nut
5/16"*12*6mm
8 PCS
9
Spring Washer
5/16"*13*2mm
8 PCS
10
Curve Washer
30"*15*7.5mm
8 PCS
11
Thread Rod
5/16*90mm 8 PCS
G3 PCS
H3 PCS
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residue and
rough surfaces and also check for staples or nails left after removing the packaging material. The manufacturer will not be held
responsible if preventative steps are not taken prior to installation.
ASSEMBLY INSTRUCTIONS:
8460-4105/4115/4901 PANEL BED, QUEEN 5/0
Thank you for purchasing this quality product. Before beginning, please check the packing material carefully for small parts which
may have come loose inside the carton during shipping. Please do not discard any packing material until all parts have been located. If
any parts are missing, please contact your dealer for prompt replacement.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged during the assembly process.
If dirty, clean finished parts with mild dishwashing liquid and water solution applied on damp cloth. Cloth should not be excessively
wet. Polish finish with soft cloth and an industry recognized furniture polish.
(3) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-
tightened to the prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and
the below mentioned components are attached to the furniture properly and kept tightened.
Parts & Hardware List:
DIAGRAM
DESCRIPTION
A
Headboard
1 PC
B
Left Post
1 PC
C
Right Post
1 PC
D
Stretcher
1 PC
E
Footboard
1 PC
F
Side Rail
2 PCS
Slats
Suppport Leg
A
E
F
D
C
B
A
Step 2
Step 3
Step 4

ASSEMBLY INSTRUCTIONS:
8460-4105/4115/4901 PANEL BED, QUEEN 5/0
Assembly Procedures:
Step 1:
Lay out all parts and hardware. Make sure the quantity of each is correct and the feet are free of
stain, staples, screws and nails.
Step 2:
Assemble the right post (B) and left post (C) to bottom stretcher (D) using hardware
provided (1,3 ,4 and 5).
Step 3:
Assemble right/left post (B and C) to headboard (A) using hardware provided (1, 2, 4 and 5) .
Step 4:
Assemble the side rails (F) to headboard (A) and footboard (E) using hardware provided
(7, 8, 9, 10 and 11) as shown.
Step 5:
Screw the support leg (H) to slats (G) .
Step 6:
Assemble the slats (G) to side rails (F) using hardware provided (6) as shown.
Assembly is complete.
www.legacyclassic.com
A
A
G
E
G
G
H
H
H
H
G
G
G
H
Step 5
Step 6