Legacy Classic Furniture 7200-621T/B User manual

ASSEMBLY INSTRUCTIONS:
Parts & Hardware List:
Thank y u f r purchasing this quality pr duct. Bef re beginning, please check the packing material carefully
f r small parts which may have c me l se inside the cart n during shipping. Please d n t discard any
packing material until all parts have been l cated. If any parts are missing, please c ntact y ur dealer f r
pr mpt replacement.
www.legacyclassic.c m
Caution: (1) These parts are cumbers me and heavy. This pr duct can best be assembled with the
assistance f ne r m re pers ns in rder t prevent pers nal injury and t insure parts are n t damaged
during the assembly pr cess. If dirty, clean finished parts with mild dishwashing liquid and water s luti n
applied n damp cl th. Cl th sh uld n t be excessively wet. P lish finish with s ft cl th and an industry
rec gnized furniture p lish.
(2) T prevent damage t y ur fl r r carpet, please check the b tt m f each piece f furniture
f r stain residue and r ugh surfaces and als check f r staples r nails left after rem ving the packaging
material. The manufacturer will n t be held resp nsible if preventative steps are n t taken pri r t
installati n.
(3) During n rmal use everyday, screws, b lts, nuts and w den plugs may l sen up. They
sh uld be peri dically inspected and re-tightened t prevent damage t the furniture and ( r) pers nal
pr perty r cause injury. Always check t be sure all hardware n this list and the bel w menti ned
c mp nents are attached t the furniture pr perly and kept tightened.
7200-621T/B OVAL PEDESTAL TABLE
HARDWARE LIST Q'TY
8 PCS
1
12 PCS2 LOCK WASHER
5/16"*2-1/4"
PARTS LIST Q'TY
1 PCA TABLE TOP
1 PC
C
MOUNTING
PLATE
B
SHORT BOLT
PARTS LIST Q'TY
E
SHORT
POST LEG
1 PC
TABLE LEAF
2 PCS
D
Step 2
5/16"
LEGACY CLASSIC
FURNITURE
HARDWARE LIST Q'TY
12 PCS
4
1 PC5
FLAT WASHER 5/16"*23*2mm
87*12mm
WRENCH
Step 3 Step 4
5
B
A
6DOWEL 8 PCS
10*40MM
7HEX WRENCH 1 PC
70*5MM
3LONG BOLT 5/16"*3" 4 PCS
7
1
2
4
7
1
2
4
7
3
24
6
6
6
6
6
6
FBASE 1 PC
LONG
POST LEG
B
B
F
D
E
F
2 PCS

ASSEMBLY INSTRUCTIONS:
www.legacyclassic.com
Assembly Procedures:
Step 1: Lay o t all parts and hardware. Make s re the q antity of each is correct and the feet are free of
stain, staples, screws and nails.
Step 2: Remove the mo nting plate (B) from the table top (A) sing wrench (5) as shown. Keep the bolts
for Step 5.
Step 3: Assemble the post leg (D & E) to the base (F) and mo nting plate (B) sing hardware (1, 2, 4, 6, 7)
as shown.
Step 4: T rn the base pright. Assemble the mo nting plate (B) to the post leg (D & E) sing hardware (3,
2, 4, 7) as shown.
Step 5: Place the entire base on the table top (A) and assemble sing hardware from Step 2 as shown.
Step 6: T rn the table to its pright position. Unlock the lock mechanism nder the table top before p lling
it apart and then caref lly remove or insert the table leaf (C) as shown.
Use the adj stable leveler as necessary.
NOTE: If handled improperly, the act of installing and removing table leaf may damage the table. Please
se ca tion and delicate handling when installing and removing table leaf to prevent damaging the
table top s rface and edges. It is best two persons are involved when installing or removing table
leaf.
Assembly is complete.
7200-621T/B OVAL PEDESTAL TABLE
LEGACY CLASSIC
FURNITURE
Step 5 Step 6
Adj stable
Leveler
5
A
C
A