Legacy Classic Furniture 8460-4106 User manual

PART QTY PART DIAGRAM DESCRIPTION QTY
1
Wrench 1 PC
2
Hexigon Bolt
1/4" x 2-1/2"
6 PCS
3
Hexigon Bolt
1/4" x 1-3/4"
4 PCS
4
Spring Washer
1/4"*11*2mm
10 PCS
5
Flat Washer
1/4"*18*2mm
10 PCS
6
Screw
Ø8*30mm 6 PCS
7
Wrench 1 PC
8
Hexagonal Nut
5/16"*12*6mm
8 PCS
9
Spring Washer
5/16"*13*2mm
8 PCS
10
Curve Washer
30"*15*7.5mm
8 PCS
11
Thread Rod
5/16*90mm 8 PCS
G3 PCS
H6 PCS
Suppport Leg
F
Side Rail
2 PCS
Slats
D
Stretcher
1 PC
E
Footboard
1 PC
B
Left Post
1 PC
C
Right Post
1 PC
(3) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-
tightened to the prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list
and the below mentioned components are attached to the furniture properly and kept tightened.
Parts & Hardware List:
DIAGRAM
DESCRIPTION
A
Headboard
1 PC
ASSEMBLY INSTRUCTIONS:
8460-4106/4116/4903 PANEL BED,CA KING 6/0
Thank you for purchasing this quality product. Before beginning, please check the packing material carefully for small parts which may have
come loose inside the carton during shipping. Please do not discard any packing material until all parts have been located. If any parts are
missing, please contact your dealer for prompt replacement.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged during the assembly process. If dirty,
clean finished parts with mild dishwashing liquid and water solution applied on damp cloth. Cloth should not be excessively wet. Polish finish
with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residue and rough surfaces
and also check for staples or nails left after removing the packaging material. The manufacturer will not be held responsible if preventative
steps are not taken prior to installation.
A
E
F
D
C
B
A
Step 3
Step 2
Step 4

Step 5:
Screw the support leg (H) to slats (G) .
Step 6:
Assemble the slats (G) to side rails (F) using hardware provided (6) as shown.
Assembly is complete.
www.legacyclassic.com
Step 2:
Assemble the right post (B) and left post (C) to bottom stretcher (D) using hardware
provided (1, 3, 4 and 5).
Step 3:
Assemble right/left post (B and C) to headboard (A) using hardware provided (1, 2, 4 and 5) .
Step 4:
Assemble the side rails (F) to headboard (A) and footboard (E) using hardware provided
(7, 8, 9, 10 and 11) as shown.
ASSEMBLY INSTRUCTIONS:
8460-4106/4116/4903 PANEL BED, CA KING 6/0
Assembly Procedures:
Step 1:
Lay out all parts and hardware. Make sure the quantity of each is correct and the feet are free of
stain, staples, screws and nails.
A
A
G
E
G
G
H
H
H
H
G
G
G
H
H
H
H
H
H
H
F
H
H
Step 5
Step 6