Legacy Classic Furniture 9180-622 User manual

AssemblyInstruction #9180-622DOUBLEPEDESTALTABLE
Page 1 of 2
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts
that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the assistance of
one or more persons in order to prevent personal injury and to insure parts are not damaged during the assembly
process. If dirty, clean finished parts with mild dishwashing liquid and water solution applied on damp cloth.
Cloth should not be excessively wet. Polish finish with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material. The
manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for packaging
carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to the
furniture properly and kept tightened at all times.
PARTS List
Code Description Qty (PCS)
A Table Leg 6 PCS
B Column Base 2 PCS
C Mending Plate 2 PCS
D Table Top 1 PC
E Table Leaf 1 PC
Hardware List See below
Hardware List
NUT
5/16"*1-1/4"
FLAT
WASHER
LOCK
WASHER
1 PC
8 PCS
BOLT
WRENCH
20 PCS
20 PCS
5/16" 12 PCS
5/16"
5/16"
Assembly Procedures:
Step 1: Lay out all parts and hardware. Make sure the quantity of each is correct.
Step 2: Rest the table top face down onto a clean soft flat surface such as a blanket and ensure that the surface is
clear of any objects that could scratch or damage the top. Remove the Mounting Plate (C) from the back
of the table top by using Wrench (4). Do not throw away the hardware when you remove the
Mounting Plate (C) as it will be used to attach this mounting plate back in the future steps.
Step 3: Attach the Table Leg (A) to the Column Base (B) by using Nut (5), Lock Washer (2) and Flat Washer (3),
and use Wrench (4) to tighten.

AssemblyInstruction #9180-622DOUBLEPEDESTALTABLE
Page 2 of 2
Step 4: Attach the Mounting Plate (C) to the Column Base (B) by using Nut (5), Lock Washer (2) and Flat Washer
(3), and use Wrench (4) to tighten.
Step 5: Attach the assembled table base to the bottom of table top (D) using the same Bolt, Lock Washer, Flat
Washer that was removed from the Mounting Plate (C) in step 2, and tighten them with wrench (4).
Step 6: Turn the whole table to the upright position. Unlock the Table Top (D) and put in the Table Leaf (E) as
shown, then lock the Table Top (D) and Table Leaf (E). If needed, adjust the levelers on the bottom of
Table Leg (A) to balance the table.
Note: If handled improperly, the act of installing and removing table leaves may damage the table. Please use
caution and delicate handling when installing and removing table leaves to prevent damaging the table top
surface and edges. It is best two (2) persons are involved when installing or removing table leaves.
A
B
C
B
A
CC
D
Step 2
Step 3 Step 4
ON OFF
ONOFF
C
D
E
Step 5 Step 6
Special Instruction: To avoid soiling carpets always wipe any excess stain residue off the bottom of the legs
with a cloth rag before assembly.
Assembly is now complete.