Legacy Classic Furniture ROUND TO OVAL PEDESTAL TABLE 9740-521 User manual

www.legacyclassic.com
ASSEMBLY INSTRUCTIONS LEGACY CLASSIC
FURNITURE
9740-521 ROUND TO OVAL PEDESTAL TABLE
Thank you for purchasing this quality product. Before beginning, please check the packing material carefully for
small parts which may have come loose inside the carton during shipping. Please do not discard any packing
material until all parts have been located. If any parts are missing, please contact your dealer for prompt
replacement.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the assistance of
one or more persons in order to prevent personal injury and to ensure parts are not damaged during the assembly
process. If dirty, clean finished parts with mild dishwashing liquid and water solution applied on damp cloth.
Cloth should not be excessively wet. Polish finish with soft cloth and an industry recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) During normal use every day, screws, bolts, nuts and wooden plugs may loosen up. They
should be periodically inspected and re-tightened to prevent damage to the furniture and (or) personal
property or cause injury. Always check to be sure all hardware on this list and the below mentioned
components are attached to the furniture properly and kept tightened.
Parts & Hardware List:
PARTS LIST
QTY
A
TABLE TOP
1 PC
B
TABLE LEAF
1 PC
C
MOUNTING PLATE
1 PC
D
LEG A
1 PC
E
LEG B
1 PC
F
CONNECTING PLATE
1 PC
Step 2
A
A
B
D E
ED
C
F
5
1
34
6
Step 3
DE
EDED
DE
C
F23
4
6
Step 4
HARDWARE LIST
QTY
HARDWARE LIST
QTY
1
ALLEN BOLT
1/4"*2-1/2"
5 PCS
4
FLAT WASHER
1/4"
13 PCS
2
ALLEN BOLT
1/4"*1-1/2"
8 PCS
5
WRENCH
10 mm
1 PC
3
LOCK WASHER
1/4''
13 PCS
6
ALLEN KEY
70*30*4mm
1 PC

www.legacyclassic.com
ASSEMBLY INSTRUCTIONS LEGACY CLASSIC
FURNITURE
9740-521 ROUND TO OVAL PEDESTAL TABLE
C
ED
E
D
F
AA
A
A
B
5
Step 5 Step 6
Assembly Procedures:
Step 1: Lay out all parts and hardware. Make sure the quantity of each is correct and the feet are free of stain,
staples, screws and nails.
Step 2: Remove the connecting plate (F) and the leaf (B) from the table top (A) using wrench (5) as shown.
Fully close the table top with the table leaf removed and lock the table top together. Keep the
bolts for step 5.
Step 3: Assemble the leg (D & E) to the mounting plate (C) using hardware (1,3,4,6) as shown.
Step 4: Turn the base upright. Assemble the connecting plate (F) to the leg (D&E) using hardware (2,3,4,6) as
shown.
Step 5: Place the entire base on the table top (A) and assemble using hardware from step 2 as shown.
Step 6: Turn the table top its upright position. Unlock the lock mechanism under the table top before pulling
it apart and then carefully insert the table leaf(B) as shown.
Use the adjustable leveler necessary. Assemble is complete.
NOTE: If handled improperly, the act of installing and removing table leaf may damage the table. Please use
Caution and delicate handling when installing and removing table leaf to prevent damaging the table
Top surface and edges. It is best two persons are involved when installing or removing table leaf.