LEGRAND HPM D642/01 User manual

• Operating range up to 50m
• 32 melodies for selection
• Weather resistant bell press
• Flashing light
• Visitor alert
• Panic button
• Pager
Wireless Door Chime
Battery Operated
Cat. No. D642/01
Instruction Manual
1 2Features Typical Applications
9Maintenance
The following suggestions will help you care for the Door Chime.
Warranty
Legrand warrants this product for a period of 3 years from
the date of purchase.
These goods come with guarantees that cannot be
excluded under the Australian and New Zealand Consumer
Laws. You are entitled to a replacement or a refund
for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired if the goods fail to be
of acceptable quality and the failure does not amount to a
major failure.
See the Warranty card enclosed with this product for
further details.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
LE07953AC 02/2022
Specifications
Bell press supply voltage: 3 V d.c
Transmission frequency: 433.05 MHz - 434.79 MHz
Range: Up to 50 m
Receiver battery voltage: 3 V d.c
Sound level: 80 dB
Battery requirement:
Door chime receiver: 2 x ‘AA’ batteries (not supplied)
Bell press transmitter: 1 x 3 V CR2032 Lithium battery (supplied)
This Chime and Bell Press are a factory set pair and are
not interchangeable with other units from HPM’s Cat. D641
series of door chimes.
Box contents
• Bell Press
• Door Chime receiver
• 1 x 3 V battery
• Mounting screws and wall plugs
• Double-sided tape
Legrand Australia
1300 369 777
www.hpm.com.au
Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
1. Keep the Door Chime dry. If the Door Chime gets wet, wipe it dry immediately. Liquids might contain
minerals that can corrode electronic circuits. 2. Use and store the Door Chime only in normal temperature
environments. Temperature extremes can shorten the life of electronic devices, damage batteries and
distort or melt plastic parts. 3. Handle the Door Chime gently and carefully. Dropping it can damage
the circuit boards and can cause the Door Chime to work improperly. 4. Keep the Door Chime away
from dust or dirt, which can cause premature wear of parts. 5. Wipe the Door Chime with a damp cloth
occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents
to clean the chime.6. Use only fresh batteries of the recommended size and type. Always remove old or
weak batteries. They can leak chemicals that can destroy electronic circuits. 7. Modifying or tampering
with the Door Chime’s internal components can cause a malfunction and might invalidate its warranty.
Please read all instructions carefully before installation and use.
HPM’s door chimes provide an easy and convenient solution for letting you know when you have
someone calling at your door. They are “Neighbour friendly”. By this we mean false triggering or
interference is prevented - every door chime and bell press pair is factory preset to communicate
on one of over 19,000 unique channels.
Paper
8Important Notes Before First Time Use
Warning
1. Dispose of used button/coin batteries
immediately by placing sticky tape around
both sides of the battery and dispose of it
immediately in an outside bin, out of reach of
children, or recycle safely. 2. If you suspect a
child has swallowed or inserted a button battery,
call the 24 Hour Poisons information Center on
131126 for expert advice.
10
THIS PRODUCT CONTAINS A COIN BATTERY
If swallowed, a lithium coin battery can
cause severe or fatal injuries within 2 hours.
Keep batteries out of reach of children.
If you think batteries may have been
swallowed or placed inside any part of the
body, seek medical attention immediately.
!
WARNING
1. Do not use rechargeable batteries, do not mix old and new batteries or different types. Alkaline batteries
are recommended in the receiver for a longer operating life.2. The operation and range of your wireless
door chime depends on location, temperature and battery condition. 3. Do not expose the chime unit to rain
or immerse either unit in water. 4. Avoid locations where the Bell Press Transmitter is exposed to direct
summer sunlight. 5. Do not leave exhausted batteries in Door Chime Receiver or Bell Press Transmitter.
6. Clean only with a damp cloth and mild detergent. Do not use solvents.

6
7
Operating Instructions
Troubleshooting
Push
Button
Selecting
Sound
Button
PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION
Your Door Chime has
stopped sounding
Your Door Chime Receiver batteries
may be flat.
Replace the batteries in your Door
Chime Receiver with 2 x AA batteries.
If the red indicator light on the Bell
Press Transmitter is no longer
illuminated then your transmitter
battery is flat.
Replace your Bell Press
Transmitter battery (1 x A23 12V)
Units are out of range (max. range to
50 metres)
Operate the chime unit with the
right range.
Wrong polarity of battery in either unit Re-insert battery with polarity to
match markings
.
Step 1: Test the location of both units to ensure satisfactory operation before permanently fixing either
unit in place.
Step 2: Do not mount the Bell Press transmitter on metal or near a metal door frame, security door
or in close proximity to any metal outdoor furniture. The range of the unit may be substantially
reduced.
Door Chime Receiver
Step 1: Depress tab on Door Chime Receiver to remove back cover plate.
Step 2: Insert 2 x ‘AA’ batteries ensuring that the coil springs contact the negative (-) end of each
battery.
The Door Chime Receiver is portable and can be placed anywhere in your house or you can
carry it with you using the belt clip at the back of the chime unit. It can also be fixed to a wall
temporarily using the mounting screws and wall plugs provided.
The Door Chime Receiver has one slotted hang hole on the back. This hole will enable the Door
Chime Receiver to be hooked onto a screw and easily removed or relocated to another room.
Bell Press Transmitter
Step 1: If using first time, pull out the plastic film to activate the battery.
Step 2: Press the Push Button to ensure that the Red
LED indicator lamp lights, indicating that the
battery is in working order.
Press the button on the Bell Press Transmitter. The Door Chime will sound and the indicator light on the
chime unit will flash.
3
4
5
Before Installation
Installation
Door Chime Operation
Mounting Holes
Back cover
Tone Selection:
The tone selector is located in the Bell Press Transmitter. To change tone, simply remove the name
plate on the Bell Press and press and hold the black selector until the desired chime is reached, then
release the selector.
Figure 1.
Figure 3.
Safety screw must be installed after replacing battery.
WARNING: Wall plugs and fixing screws are provided with this
kit, but may not be suitable for all installations. Ensure you use
a method of fixing appropriate to your mounting surface.
The Bell Press is suitable for outdoor use, however for best performance and a longer life the Bell Press
should not be exposed to direct sunlight or rain. The device can also be used as a remote control and
doesn’t require any installation.
NOTE: Try different locations in your home, before fixing your
products in place. Both units should be more than 1 metre
from the floor. Move Door Chime Receiver closer to Bell Press
Transmitter to improve operation.
Step 3: With the help of screwdriver depress the clip
before pulling the cover out (See Fig.2). Fix the
unit to your front door or a position close by
using the double-sided tape or mounting
screws provided. If using screws provided, you
will need to remove the back cover and fix it
to the wall, then reattach the bell press to the
back cover.
If you have checked
your batteries and your
Door Chime is still not
operating
Check the distance between your Door
Chime and Bell Press, they may be
located too far away from each other.
Relocate the Door Chime
Receiver closer to the Bell Press
Your Bell Press may be located too
close to a metal structure or too close
to the ground.
Relocate your Bell Press away from the
metal structure or further away from
the ground.
Selected chime has
changed
Battery in a Bell Press unit
was replaced.
Refer to “tone selection”
COIN BATTERY
Figure 2.