LEGRAND IS-0387 User manual

INSTRUCTION / INSTALLATION SHEET
Selective Call Intercom Door Unit
IS-0387 Rev. B
301Fulling Mill Road, Suite G
Middletown, PA 17057
Phone [phone] / Fax [phone]
www.onqlegrand.com
©Copyright 2011 by Legrand All Rights Reserved. Page 1 of 3
1. Introduction
The Legrand Selective Call Intercom Door Unit, PN IC5002-XX (see Figure
1), is a weather resistant door unit that allows a visitor to notify the occupants
of their presence by pushing the door chime button. The occupants can then
initiate two-way communications with the visitor and open the door (requires
separate door release device). The Door Unit is available in white (-WH),
shiny brass (-SB), antique brass (-AB), brushed stainless (-BS) and oil-
rubbed bronze (-OB).
2. Description
The Door Unit is a 2-gang product that mounts within an outdoor
weatherproof box (56” from the floor to the bottom of the box). There is
also a two-gang surface-mount box available (P/N IC5006-BK) for unique
or retrofit installation requirements.
3. Installation
Installation of the Selective Call Door Unit is best accomplished at multiple times during new construction, at
“Rough-in” before the drywall and siding is installed, and at “Trim-out” after the drywall is installed.
A. “Rough-in” steps:
1. Run a Cat 5 cable from the Enclosure where the Selective Call Intercom Module will be installed to the
2 gang box at the Door Unit location.
NOTE: The maximum Cat 5 cable run distance between the SCI Module and another unit (Module,
Door, Patio or Room Unit) is 330’ with the following exception. One Door or Patio Unit may be placed
up to 1000’ (up to 650’ for a Video Door Unit) from the SCI Module, but it needs to be locally powered
and Legrand needs to be informed of and pre-approve this type of installation. If the Cat 5 run is
buried in an underground conduit, it should maintain a 16” separation from any 110VAC wiring.
Additional SCI Modules are recommended to be placed in the same enclosure, powered from the
same power strip, and interconnected with the shortest Cat 5 connections possible.
NOTE: It is important to keep all in-wall Category 5e cable runs at least 12 inches away from AC
electrical cables. If it proves necessary to cross an existing AC cable, do so only at a 90 degree angle.
B. “Trim-out” steps:
NOTE: All terminations can be correctly completed by following the T568A pin assignments. It is
important that you accurately terminate using T568A at all locations. All terminations on the Selective Call
Intercom System utilize RJ45 jacks. Refer to Figure 2 for correct T568A termination for RJ45 plugs.
RJ-45
Pin
1 – White/Green
2 – Green
3 – White Orange
4 – Blue
5 – White/Blue
6 – Orange
7 – White/Brown
8 – Brown
RJ-45
Pin
1 – White/Green
2 – Green
3 – White Orange
4 – Blue
5 – White/Blue
6 – Orange
7 – White/Brown
8 – Brown
Figure 1
Figure 2

INSTRUCTION / INSTALLATION SHEET
Selective Call Intercom Door Unit
IS-0387 Rev. B
301Fulling Mill Road, Suite G
Middletown, PA 17057
Phone [phone] / Fax [phone]
www.onqlegrand.com
©Copyright 2011 by Legrand All Rights Reserved. Page 2 of 3
NOTE: Make sure that the included weather proofing gasket is placed as shown in Figure 3.
1. As shown in Figure 3, the first step to installing the
Selective Call Door Unit is to place the included rear
gasket against the gang or back box, and secure the
gasket in place with the included mounting bracket.
NOTE: Insure that the mounting bracket is installed with
the center tab pointed up, as the Door Unit will be
“hung” from this tab in a later step.
NOTE: There are slotted holes in the mounting bracket
to allow for leveling of the Door Unit in case the gang or
back box was installed off level.
2. Use the four provided screws to attach the mounting
bracket to the gang or back box.
3. Pull the Cat 5 cable from the enclosure through the mounting bracket and terminate the cable with an
RJ45 plug and insert the plug into the RJ45 jack on the rear of the Door Unit (see Figure 4). Follow
the T568A standards described in Figure 2.
NOTE: There is a four position terminal block on the rear
of the Door Unit that can be utilized for two different
purposes (see Figure 5). The CHIME output is a normally
open dry contact closure used to ring a customers 3rd
party door chime when the Door Unit button is pressed.
The SENSOR input is reserved for a future application.
4. Hang the Door Unit from the top tab on the mounting bracket and
use the provided 1/16” allen wrench to tighten the two set screws
at the bottom of the Door Unit.
5. Terminate the other end of the Cat 5 cable, at the Selective Call
Intercom Module, with an RJ45 plug using the T568A wiring
standard.
6. Insert the RJ45 plug into any of
the eight Room, Patio, or Door
Unit jacks on the Intercom Module
(labeled 1-8).
7. After all Units and Modules are
connected, apply power to the
Selective Call Intercom Module
and verify system functionality. All
Selective Call Room, Door and
Patio Units will be discovered and
shown on each Room Unit LCD.
Figure 3
rear
gasket
center tab
mounting
bracket
set screws
RJ45
jack
Figure 4
Figure 5

INSTRUCTION / INSTALLATION SHEET
Selective Call Intercom Door Unit
IS-0387 Rev. B
301Fulling Mill Road, Suite G
Middletown, PA 17057
Phone [phone] / Fax [phone]
www.onqlegrand.com
©Copyright 2011 by Legrand All Rights Reserved. Page 3 of 3
4. Operation
Please refer to Figure 6 to familiarize yourself with the basic operation of the Selective Call Door Unit. Please
refer to the Selective Call System Installation Manual (P/N 1308003) shipped with the SCI Module for more
detailed instructions on how to use any Selective Call Room Unit to configure and personalize the Selective Call
System.
NOTE: Refer to the Selective Call Intercom Module Information Sheet (IS-0385) shipped with the
Distribution Module for information regarding the support for electronic door release functionality.
Figure 6 Door Chime Button: When a visitor
pushes this button, one of 20 selectable
Door Chimes will be heard throughout the
home at each active intercom unit. The
occupants of the home can then talk to that
Door Unit from any Room or enabled Patio
Unit. The visitor will hear the occupant over
the Door Unit speaker and be able to talk to
them over the Door Unit microphone. The
occupant may also choose to release the
electronic door latch (if equipped) and let
the visitor in.
Speaker
Microphone