Legrand Kenall tekdek td17 series User manual

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

F-4260_091118

Luminaire for Parking Garages

TEKDEK™LED

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE

L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET

LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.

DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN

ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT

CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND

LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL

INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS

INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

SAFETY RECOMMENDATION

TD17 SERIES

SAFETY RECOMMENDATION

A 1/16" diameter aircraft cable with end-loop (not included) is recommended for

attaching the xture structural to the upper structural.

1/16" DIA. AIRCRAFT CABLE

(SUPPLIED BY OTHERS)

AIRCRAFT CABLE ATTACH

TO UPPER STRUCTURAL

SCREW (SUPPLIED BY OTHERS)

A 1/16" diameter cable with end-loop (not included) is recommended

for attaching the xture structural to the upper structural

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

F-4260_091118

1: Remove tertiary lens (if provided) by unscrewing (4) captive screws.

2: Remove heatsinking/LED base by unscrewing (4) captive screws.

These will be the inner most screws.

3: Disconnect the quick connector wires from the LED board and

the driver.

4: Make electrical connection to J-box (for sizes, see next page). Circuit

wire connection must be in J-box. Install housing to surface using (4)

5/16" diameter mounting holes.

5: Re-assemble by reversing the removal procedure.

DRIVER

QUICK CONNECT HEATSINK/LED BASE

CAPTIVE SCREWS (4)

FOR REMOVING HEATSINK

CAPTIVE SCREWS (4)

TERTIARY LENS (IF PROVIDED)

HOUSING

HOUSING TOP VIEW

5/16” MOUNTING HOLES (4)

DIRECT TO SURFACE INSTALLATION

INSTALLATION INSTRUCTIONS

F-4258_091118

QUICK MOUNT KIT INSTALLATION

1: Quick mount plate fastens to a secure J-box.

Screws by others.

2: Align hanger bracket with center slot on

top of xture as shown at right. Fixture

can then hang from bracket while electrical

connections are made.

3: After excess wires are in J-box (see sizes

below), push the xture up to the mounting

plate. Locking hooks should slide through

slots. Twist xture until a “click” is felt or

heard. Fixture is now in place.

LOCKING HOOKS

HANGER BRACKET QUICK MOUNT PLATE

ALIGN HANGER BRACKET

WITH CENTER SLOT

LOCKING HOOK

SLOTS

USED WITH THE FOLLOWING

JUNCTION BOX SIZES:

4" ROUND

4" SQUARE

3-1/2" OCTAGON

3.37

2.50

4.77

3.50

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents

INSTALLATION INSTRUCTIONS

F-4557_041013

BIRD GUARD INSTALLATION

1. Fasten tab through slots as shown above.

No tools required. Must install before xture is mounted.

2. Bird Guard lays inside of casting.

DIRECT TO SURFACE & QUICK MOUNT

INSTALLATION INSTRUCTIONS

F-4259_091118

PENDANT MOUNT INSTALLATION

1: Attach 3/4" threaded conduit to

housing (provided by others).

2: Make electrical connections in

conduit body (supplied by others).

CONDUIT BODY AND

CONDUIT (BY OTHERS)

HOUSING TAPPED FOR

3/4” NPS THREAD

MUST USE SEALANT OR

SEALING LOCKNUT

SWIVEL MOUNT NOT RECOMMENDED

(Kenall does not supply counterbalance system)

INSTALLATION INSTRUCTIONS

F-4257_091118

TRUNNION KIT INSTALLATION

1: Attach housing plate to housing. Align

notch. Use (4) at head screws (provided).

2: Assemble trunninon kits as shown using (4)

¼-20 × .500" screws and nuts (provided).

3: Attach trunnion brackets to housing plate

with (4) 10-32 × .375" hex head screws

(provided).

4: Make electrical connections in conduit body

(supplied by others).

NOTE: Top of bracket to top of the xture

measurements: 9.1" min; 14.6" max

TRUNNION BRACKETS

CONDUIT BODY AND

CONDUIT (BY OTHERS)

HOUSING

PLATE

HOUSING

(To increase depth,

move this fastner here)

MUST USE SEALANT OR

SEALING LOCKNUT

INSTALLATION INSTRUCTIONS

F-4558_041013

Luminaire for Parking Garages

TEKDEK™ LED

1. Bird Guard lays on top of casting.

TD17 SERIES

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE

CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET LE

FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.

DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO

NOT CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.

SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING ORIENTATION, OR

MOUNTING RESTRICTIONS.

SAVE THESE INSTRUCTIONS

Pendant Mount

Trunnion Kit

BIRD GUARD INSTALLATION - PENDANT MOUNT & TRUNNION KIT

(For Trunnion Kit remove tabs)

2. Attach both sides with (4) screws provided.

NOTE: For LEL option, align hole in bird guard with LED indicator

INSTALLATION INSTRUCTIONS

F-4257_091118

MOUNT FIXTURE WITH REGARDS TO

OPTICAL ALIGNMENT KEY DIRECTION

TYPES II, III, IV

TYPE V, NORMAL

TYPE V, SQUARE

TYPE II

TYPE III

TYPE IV

TYPE V

NORMAL

TYPE V

SQUARE

LIGHT DISTRIBUTION

PATTERN TYPES

DRIVING

LANE

DRIVING

LANE

KEY

OPTICAL

ALIGNMENT KEY

For warranty information visit www.kenall.com/Resources/Certied-Performance-Warranties

For technical assistance, call 1-800-4KENALL (1-800-453-6255).

WARRANTY

CUSTOMER SERVICE

www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA

This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents