LEGRAND Raritan Dominion LX II Series User manual

Dominion LX II Quick Setup Guide
1
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
Dominion® LX II
Thank for choosing the Dominion LX II, designed for
economical, reliable and secure remote access and
management.
This Quick Setup Guide explains how to install and
configure the LX II.
Package Contents
Each LX II ships as a stand-alone product in a standard 1U 19" rackmount chassis.
The LX II device ships with the following contents:
•1 - LX II device
•1 - LX II Quick Setup Guide
•1 - Rackmount kit
•1 - AC power cord
•1 - Set of 4 rubber feet (for desktop use)
•1 - Warranty card
QS Rule
In Raritan products that require Rack Mounting, please follow these precautions:
•Operation temperature in a closed rack environment may be greater than room temperature. Do not exceed the rated maximum ambient
temperature of the appliances. See Specifications in Administrators Guide.
•Ensure sufficient airflow through the rack environment.
•Mount equipment in the rack carefully to avoid uneven mechanical loading.
•Connect equipment to the supply circuit carefully to avoid overloading circuits.
•Ground all equipment properly, especially supply connections, such as power strips (other than direct connections), to the branch circuit.
QS Rule
Rack Mounting
The LX II can be mounted in 1U (1.73", 44 mm) of vertical space in a standard 19" equipment rack. You can mount the LX II facing the front of the
rack or facing the rear of the rack.
To rack-mount the LX II, use the brackets and screws that came with the device.
Forward Mount
The steps in the table correspond to the numbers shown in the front rackmount diagrams.
1. Secure the cable-support bar to the back end of the side brackets using two of the included screws.
QUICK SETUP GUIDE
DLX2-108, DLX2-116, DLX2-216

Dominion LX II Quick Setup Guide
2
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
2. Slide the LX II between the side brackets, with its rear panel facing the cable-support bar, until its front panel is flush with the "ears" of the
side brackets.
3. Secure the LX II to the side brackets using the remaining included screws (three on each side).
4. Mount the entire assembly in your rack and secure the side brackets' ears to the rack's front rails with your own screws, bolts, cage nuts, and
so on.
5. When connecting cables to the rear panel of the LX II, drape them over the cable-support bar.
Rear Mount
The steps in the table correspond to the numbers shown in the rear rackmount diagrams.
1. Secure the cable-support bar to the front end of the side brackets, near the side brackets' "ears," using two of the included screws.
2. Slide the LX II between the side brackets, with its rear panel facing the cable-support bar, until its front panel is flush with the back edges of
the side brackets.
3. Secure the LX II to the side brackets using the remaining included screws (three on each side).
4. Mount the entire assembly in your rack and secure the side brackets' ears to the rack's front rails with your own screws, bolts, cage nuts, and
so on.
5. When connecting cables to the rear panel of the LX II, drape them over the cable-support bar.
QS Rule
Step 1: Configuring Network Firewall Settings
TCP Port 5000
Enable remote access to LX II by allowing network and firewall
communication on TCP Port 5000.
Alternatively, configure LX II to use a different TCP port, and allow
that port network and firewall communication.
TCP Port 443
Allow access to TCP Port 443 (Standard HTTPS) so you can access LX
II via a web browser.
TCP Port 80
Allow access to TCP Port 80 (Standard HTTP) to enable automatic
redirection of HTTP requests to HTTPS.
QS Rule
Step 2: Configuring KVM Target Servers
Mouse Settings
Absolute Mouse Synchronization is recommended to minimize
mouse settings on target servers.
In this mode, absolute coordinates are used to keep the client and
target cursors in synch, even when the target mouse is set to a
different acceleration or speed.
This mode is supported on servers with USB ports and is the default
mode for virtual media CIMs.
•Absolute Mouse Synchronization requires the use of a virtual
media CIM - D2CIM-VUSB, D2CIM-DVUSB, D2CIM-DVUSB-DVI,
D2CIM-DVUSB-HDMI, D2CIM-DVUSB-DP
Target Server Video Resolutions
See Supported Target Server Video Resolutions in Online Help.
QS Rule

Dominion LX II Quick Setup Guide
3
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
Step 3: Connecting the Equipment
A. AC Power
To connect the power supply:
•Attach the included AC power cord to the LX II and plug it into an AC power outlet.
B: Local Access Ports
To connect a local PC:
Attach a multi-sync VGA monitor, and USB mouse and keyboard.
C: Network Port
To connect the network:
•Connect a standard Ethernet cable from the network port to an Ethernet switch, hub, or router.
D: Target Server Ports
To connect target servers:
1. Connect the keyboard, mouse and video plugs on the CIM to the corresponding ports on the target server.
2. Connect the CIM to an available target server port on the back of the LX II via a Cat5/5e/6 cable.
E: Modem Port (Optional)
See Configuring Modem Settings, in the Online Help.
QS Rule
Step 4: Configuring the LX II
For the following steps, you must change the default password and
assign the LX II its IP address at the Local Console.
All other steps can be performed either from the Local Console, or
the LX II Remote Console via a supported web browser using the LX
II's default IP address.
Java is required to use the Java-based VKC/VKCS client. See the
Release Notes for supported versions.
Microsoft .NET is required to use the Microsoft Windows-based
AKC client. See the Release Notes for supported versions.
Factory Default Login Information
The LX II device is shipped with the following default settings:
•Username = admin
•Password = raritan
•IP address = 192.168.0.192
Important: For backup and business continuity purposes, it is
strongly recommended you create a backup administrator
username and password, and keep that information in a secure
location.
Change the Default Password
The first time you start the LX II device, you are required to change
the default password.
1. Once the unit has booted, enter the default username admin
and password raritan.
2. Click Login.
3. Enter the old password raritan, then enter and reenter a
new password.
Up to 64 English alphanumeric and special characters.
4. Click Apply, then click OK on the Confirmation page.

Dominion LX II Quick Setup Guide
4
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
Assign the LX II a Device Name
Choose Device Settings > Network to go to the Basic Network
Settings page in the LX II Remote client.
•Specify a meaningful Device Name for your LX II device.
Up to 32 alphanumeric and valid special characters, no
spaces between characters.
Next, configure the IP address and DNS settings.
Configure the Network: IPv4 and IPv6 Settings
1. Set the IP Auto Configuration to None in the IPv4 section.
2. Enter the IP address you want to use to connect to the LX II
LAN1. The default IP address is 192.168.0.192.
3. Enter the IPv4 Subnet Mask. The default subnet mask is
255.255.255.0.
4. Complete the IPv6 sections, if applicable.
5. Select the IP Auto Configuration. If None is selected, you must
manually specify -
Global/Unique IP Address - this is the IP address assigned to
LX II.
Prefix Length - this is the number of bits used in the IPv6
address.
Gateway IP Address.
Select Router Discovery to locate a Global or Unique IPv6
address instead of a Link-Local subnet. Once located, the
address is automatically applied.
Note that the following additional, read-only information
appears in this section -
Link-Local IP Address - this address is automatically
assigned to the device. It is used for neighbor discovery or
when no routers are present.
Zone ID - Identifies the device the address is associated
with. Read-Only
6. Select "Use the Following DNS Server Addresses" and enter the
Primary DNS Server IP Address and Secondary DNS Server IP
Address. The secondary addresse is used if the primary DNS
server connection is lost due to an outage.
Note: "Obtain DNS Server Address Automatically" and
"Preferred DHCP Host Name" are only enabled when LX II is
configured in DHCP mode
7. When finished, click OK. Your LX II device is now accessible via
the LAN IP address.
Name Your Target Servers
1. Connect all of the target servers if you have not already done
so.
2. Select Device Settings > Port Configuration, then click the Port
Name of the target server you want to name.
3. Enter a name for the server. Up to 32 alphanumeric and special
characters. Click OK.
Configure Date/Time Settings
The date and time settings impact SSL certificate validation if LDAPS
is enabled. Configuring the date and time also ensures your audit
logs will be timestamped correctly.
There are two ways to do this:
•Manually set the date and time.

Dominion LX II Quick Setup Guide
5
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
•Synchronize the date and time with a Network Time Protocol
(NTP) server.
1. Choose Device Settings > Date/Time to open the Date/Time
Settings page.
2. Choose your time zone from the Time Zone drop-down list.
3. Adjust for daylight savings time by checking the "Adjust for
daylight savings time" checkbox.
4. Choose the method to use to set the date and time:
User Specified Time - use this option to input the date and
time manually. For the User Specified Time option, enter
the date and time. For the time, use the hh:mm format
(using a 24-hour clock).
Synchronize with NTP Server - use this option to
synchronize the date and time with the Network Time
Protocol (NTP) Server.
For the Synchronize with NTP Server option:
Enter the IP address of the Primary Time server.
Enter the IP address of the Secondary Time server.
Optional
Note: If DHCP is selected for the Network Settings on the
Network page, the NTP server IP address is automatically
retrieved from the DHCP server by default. Manually enter the
NTP server IP address by selecting the Override DHCP
checkbox.
5. Click OK.
QS Rule
Step 5: Launching the Remote Console
1. Launch a supported web browser, and enter the IP address
assigned to the LX II. A default client is launched based on your
pc and browser settings. See the online help for details about
clients.
2. Enter your username and password, then click Login.
3. Accept the user agreement (if applicable).
4. If security warnings appear, click to accept.
Access and Control Target Servers Remotely
The LX II Port Access page provides a list of all LX II ports.
The page also lists all of the target servers connected to the LX II
along with their status and availability.
Access a Target Server from the LX II
1. On the Port Access page, click the Port Name of the target you
want to access. The Port Action Menu is displayed.
2. Choose Connect from the Port Action menu.
A KVM window opens with a connection to the target.
Switch between Target Servers
1
While already using a target server, access the LX II
Port Access page.
2
Click the port name of the target you want to access.
The Port Action menu appears.
3
Choose Switch From. The new target server you
selected is displayed.

Dominion LX II Quick Setup Guide
6
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
Disconnect from a Target Server
To disconnect a target:
•On the Port Access page, click the port name of the target you
want to disconnect from, then click Disconnect on the Port
Action menu when it appears.
Or
•Close the client window.
QS Rule
Step 6: Configuring the Keyboard Language (Optional)
Note: This step is not required if you are using the US/International
language keyboard.
If you are using a non-US language, the keyboard must be
configured for the appropriate language.
Additionally, the keyboard language for the client machine and the
KVM target servers must match.
Consult your operating system documentation for additional
information about changing the keyboard layout.
QS Rule
Step 7: Create and Install an SSL Certificate
It is strongly recommended to install your own SSL Certificate in
each LX II device.
This security best practice reduces the number of Java™warning
messages, and avoids man-in-the-middle attacks.
It also prevents future Java versions and browser versions from
blocking access to your LX II device.
For information on creating and installing SSL certificates, see LX II
Online Help.
Converting a Binary Certificate to a Base64-Encoded DER
Certificate (Optional)
LX II requires an SSL certificate in either Base64-Encoded DER
format or PEM format.
If you are using an SSL certificate in binary format, you cannot
install it.
However, you can convert your binary SSL certificate.
1. Locate the DEGHKVM0001.cer binary file on your Windows
machine.
Double-click on the DEGHKVM0001.cer file to open its
Certificate dialog.
2. Click the Detail tab.
3. Click "Copy to File...".

Dominion LX II Quick Setup Guide
7
QSG
-DLX2-v3.0.0-0A-E 255-62-0024-00
4. The Certificate Export Wizard opens. Click Next to start the
Wizard.
5. Select "Base-64 encoded X.509" in the second Wizard dialog.
6. Click Next to save the file as a Base-64 encoded X.509.
You can now install the certificate on your LX II.
QS Rule
Additional Information
For more information about LX II and the entire Raritan product line, see Raritan's
website (www.raritan.com). For technical issues, contact Raritan Technical Support.
See the Contact Support page in the Support section on Raritan's website for technical
support contact information worldwide.
Raritan's products use code licensed under the GPL and LGPL. You can request a copy
of the open source code. For details, see the Open Source Software Statement at
(http://www.raritan.com/about/legal-statements/open-source-software-statement/)
on Raritan's website.