LEGRAND ZLGP12 User manual

Stickers
x2
Setup button
Up
Down
Stop
Do not remove the cover
plates
Roller shutter control
Frequency bands: 2.4 - 2.4835 GHz
Power level: < 20 mW
Module Control Gateway power outlet and home/away
wireless master switch
LE12487AB-EN
Wireless and batteryless roller shutter control
0 676 46L/47L - 0 677 64L
0 770 55L - 6 000 87L
7 418 08L/38L/68L
Requires to install the connected starter pack and one or more «... with Netatmo» connected switches for roller
shutters first.
Or
Pack contents:

2
> 3 s
Start the configuration
Press the configuration button of Module Control or press the middle of the wireless master switch until its light
briefly turns green, and then stop pressing. All wired products lights will turn green.
1
Or

3
C
A
B
+
Pair the wireless, batteryless switch to control the connected roller shutter switches
2
Multiple pairing : You can control several roller shutter switches with the same wireless, batteryless switch by
repeating the operation for each product that you want to control.
Make sure that the indicator lights on the wired products are green.
If not, go back to precedent step. 1.
Tap 3 times the roller shutter switch you want to control with the wireless, batteryless control. The light of the
roller shutter switch flashes rapidly.
While pressing the «setup» button, press briefly the «Stop» or «Up» or «Down» button.
The indicator lights of the product to control will briefly turn blue, and then will turn green again.
The pairing was successful.
Check the correct pairing by pressing Up and then Down buttons
A
B
C
To complete your installation, briey press the congu-
ration of the Module Control or the middle of the wire-
less Home / Away master switch.
All the indicator lights on the products switch o.
Complete the installation
3
< 1 s
Or
< 1 s
+
If necessary, erase the conguration of the wireless
batteryless control (factory reset)
While holding the "setup" button on the wireless,
batteryless control, press the "Up" button for 5 seconds.
Conrm that your control is correctly reset by making an
Up command, then Down.
5 s

4
H > 2 m
H < 2 m
Put the stickers in place
T
he undersigned, Legrand declares that the radio-electric equipment type
(0 676 46L/47L - 0677 64L - 0 770 55L - 6 000 87L - 7 418 08L/38L/68L)
complies with directive 2014/53/EU. The full text of the EU declaration of
conformity is available on the following website: www.legrandoc.com
You can also fix the wireless switch(es) permanently to
the wall with screws.
Before fixing the wireless switch(es) with
the removable stickers provided, test one
on a non-visible area of the wall.
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
www.legrandoc.com/067646L
Download the app
Your installation is ready. You can download the Legrand Home +
Control application to control your roller shutters remotely.
Model: ZLGP12
FCC ID: 2ACN8-ZLGP1X IC: 12132A-ZLGP1X Model : ZLGP12
This device contains licence-exempt transmitter(s)/receiver(s) that comply withFCC RF andInnovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the device.
This device complies with FCC and ISED radiation exposure limits set forth for general population. This device must not be co-located or
operating in conjunction with any other antenna or transmitter.
FCC Caution: the user that changes or modications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by turning the equipment o and on, the user is encouraged to try to correct
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety instructions
Make sure the power supply is disconnected before any intervention.
Strictly comply with instructions for installation and use.