Leica HDS7000 User manual

HDS7000
User Manual
Version 1.1
English

2
HDS7000, Introduction
Introduction
Purchase Congratulations on the purchase of a HDS7000 instrument.
This manual contains important safety directions as well as instructions for setting
up the product and operating it. Refer to "6 Safety Directions" for further informa-
tion.
Read carefully through the User Manual before you switch on the product.
Product
identification
The type and the serial number of your product are indicated on the type plate.
Enter the model and serial number in your manual and always refer to this informa-
tion when you need to contact your agency or Leica Geosystems authorised service
workshop.
Type: _______________
Serial No.: _______________

HDS7000, Introduction 3
Symbols The symbols used in this manual have the following meanings:
Trademarks • Windows is a registered trademark of Microsoft Corporation
All other trademarks are the property of their respective owners.
Type Description
Danger Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Warning Indicates a potentially hazardous situation or an unintended
use which, if not avoided, could result in death or serious injury.
Caution Indicates a potentially hazardous situation or an unintended
use which, if not avoided, may result in minor or moderate
injury and/or appreciable material, financial and environmental
damage.
)Important paragraphs which must be adhered to in practice as
they enable the product to be used in a technically correct and
efficient manner.

4
HDS7000, Table of Contents
Table of Contents
In this manual Chapter Page
1 Description of the System 8
1.1 Packing / Unpacking 8
1.2 Container Contents 9
1.3 Instrument Components 11
1.4 Cabling 16
1.4.1 Operate the HDS7000 with the Battery 16
1.4.2 Operate the HDS7000 with the Battery Charger
(AC Power Supply) 22
1.4.3 USB Ports 24
1.5 Field of View (FOV) 26
1.6 HDS Cyclone Software Suite 27
2 Setting Up the Instrument 30
2.1 General Information 30
2.2 Scanner Setup on Tripod 31
2.3 Setup Over a Benchmark with the Internal Laser Plummet 33
2.4 Instrument Height 36
2.5 Setting Up the Instrument with the Dolly 37

HDS7000, Table of Contents 5
3Scanning 38
3.1 Switching the System On/Off 38
3.2 Preparations 39
3.3 Ambient Conditions 42
3.4 Onboard Controls 45
3.5 Main Menu 51
3.6 Scanning 53
3.6.1 Level 57
3.6.2 Start Predefined Scan 59
3.6.3 Scan with User Defined Settings 60
3.6.4 Profile Scanning 68
3.6.5 Panorama 69
3.6.6 One Target Orientation (1-TO) 71
3.6.7 Setup a Predefined Scan 73
3.7 Scans 74
3.8 Help 83
3.9 Status 84
3.10 Settings 86
3.11 Hardware 89
3.12 Connections 92
3.12.1 Connecting the HDS7000 to a Network by Cable 94
3.12.2 Connecting the HDS7000 to a Notebook by Cable 96
3.12.3 Connecting the HDS7000 by Wi-Fi 99
3.13 Operating the HDS7000 using a Web Browser 100

6
HDS7000, Table of Contents
4 Troubleshooting 104
5 Care and Transport 108
5.1 Check & Adjust 108
5.2 Transport 109
5.3 Storage 110
5.4 Cleaning and Drying 111
5.5 Window Cleaning Procedure 112
5.6 Adjustment of the Circular Level 114
5.7 Service of the Tripod 115
6 Safety Directions 116
6.1 General Description 116
6.2 Intended Use 117
6.3 Limits of Use 119
6.4 Responsibilities 120
6.5 Hazards of Use 121
6.6 Laser Classification Scanner, Invisible Laser 130
6.7 Electromagnetic Compatibility EMC 132
6.8 FCC Statement, Applicable in U.S. 135

HDS7000, Table of Contents 7
7 Technical Data 140
7.1 General Technical Data of the Instrument 140
7.2 Laser Scanning System 141
7.3 Miscellaneous 144
7.3.1 Electrical 145
7.4 Environmental 146
7.5 Physical 147
7.6 Accessories 148
7.7 Wi-Fi 150
7.8 Conformity to National Regulations 151
8 International Limited Warranty, Software Licence Agreement 152
Index 154

8
HDS7000, Description of the System
1 Description of the System
1.1 Packing / Unpacking
Unpacking When in its transport container, the HDS7000 sits in with the Wi-Fi antenna in face-
up position.
)Pack the instrument the same way it is delivered.
To take the instrument out of its container,
grasp the handle and the base of the instru-
ment, and lift.
Use caution due to the weight of the instru-
ment (9.8 kg).
HDS7000_001

HDS7000, Description of the System 9
1.2 Container Contents
Transport
container for
HDS7000
a) USB plug
b) User Manual
c) HDS7000
d) Glass cleaning kit
HDS7000_002
a
b
c
d

10
HDS7000, Description of the System
Transport
container for
HDS7000 accesso-
ries
a) AC power supply / battery
charger
b) Charging cradle
c) HDS7000 battery
d) Ethernet cable
e) Extension cable for AC power
supply
f) Power cable for AC power
supply
HDS7000_003
a
b
c
d
e
f

HDS7000, Description of the System 11
1.3 Instrument Components
Overall system
a) HDS7000
b) Rechargeable internal battery
("battery" will be used)
c) Tribrach
d) Tripod
e) Cleaning kit
f) Transport container for HDS7000
accessories
g) Transport container for HDS7000
h) Ethernet cable
i) Extension cable for AC power
supply / battery charger
j) Power cable for AC power supply
k) AC power supply
l) Charging cradle
h
i
j
k
l
a
b
c
d
e
f
g
HDS7000_004
HDS7000

12
HDS7000, Description of the System
Hardware options • USB plug (32 GB)
• HDS7000 scan targets and target accessories
• Dolly
HDS7000
a) Handle
b) Wi-Fi antenna
c) ON/OFF button
d) Touch screen / Display
e) Rotating mirror (Laser exit)
f) Designated slot for stylus-pen
g) USB Connectors, P1, P2
h) Lemo Connectors, P3, P4
i) Ethernet connector
j) Connector for power supply
k) Laser plummet
a
b
c
d
i
j
k
e
f
g
h
HDS7000_005
HDS7000

HDS7000, Description of the System 13
Battery and
charging cradle
)Use the SupD-9 plug only for connecting to the battery.
a) Battery
b) Charging cradle
c) Battery status indicators
d) Connector for power supply
e) Green LED: Power indicator
LED
f) Red LED: Error LED
g) SupD-9 plug: connects
battery and charging cradle
a
b
cdefg
HDS7000_006
ERR

14
HDS7000, Description of the System
AC power supply /
Battery charger
a) Power cable for AC power
supply
b) AC power supply
c) Lemo plug (3 pin, female)
a
b
c
HDS7000_007

HDS7000, Description of the System 15
Extension cable for
AC power supply
Ethernet cable
a) Cable
b) Connector 3 pin, female
c) Connector 3 pin, male
a
c
b
a) Cable
b) Connector, 8 pin male
c) Ethernet connector
a
b
c
GEV228

16
HDS7000, Description of the System
1.4 Cabling
1.4.1 Operate the HDS7000 with the Battery
Change the battery
)A battery should always be attached to ensure the optimum weight balance for the
HDS7000. If there is no removable battery connected, a warning message appears.
1. Hold the battery with both hands and
press the fixing clips.
2. Pull the battery carefully downwards.
HDS7000_008
2
1
1
HDS7000

HDS7000, Description of the System 17
)Never remove the battery while the HDS7000 is switched on.
Precautions:
• Switch off the HDS7000 beforehand or
• use the external power supply
)If the HDS7000 is operated until the battery is completely empty, it has to be
recharged immediately. Failure to do this can result in battery damage.
)Primary use/charging
• The batteries must be charged prior to using for the first time because it is deliv-
ered with an energy content as low as possible.
• For new batteries or batteries that have been stored for a long time (> three
months), it is effectual to make only one charge/discharge cycle.
• For Li-Ion batteries, a single discharging and charging cycle is sufficient. We
recommend carrying out the process when the battery capacity indicated on the
charger or on a Leica Geosystems product deviates significantly from the actual
battery capacity available.
• The permissible temperature range for charging is between 0°C to 40°C / +32°F
to +104°F. For optimal charging we recommend charging the batteries at a low
ambient temperature of +10°C to +20°C / +50°F to +68°F if possible.
• It is normal for the battery to become warm during charging. Using the chargers
recommended by Leica Geosystems, it is not possible to charge the battery if the
temperature is too high.

18
HDS7000, Description of the System
Operation/Discharging
• The batteries can be operated from -20°C to +55°C / -4°F to +131°F.
• Low operating temperatures reduce the capacity that can be drawn; very high
operating temperatures reduce the service life of the battery.
Charging the
battery
1. Plug the power cable into the battery
charger and into an AC plug.
2. Using the HDS7000 power supply cable
connect the charging cradle and the
battery charger.
3. Place the battery onto the charging
cradle.
4. After 30sec initialization, the charging
cradle’s battery status indicators will indi-
cate the current battery charging status.
5. Disconnect the cables.
HDS7000_009
1
1
2
3
ERR

HDS7000, Description of the System 19
)Charging of the battery takes approximately 1.5 hours.
Understand the charging cradle’s LEDs:
a) Battery status indicators
b) Power indicator LED (green)
c) Error LED (red)
HDS7000_010
a
b
c
ERR

20
HDS7000, Description of the System
Battery status
indicators
• If all four LEDs flash continuously then there is no battery in
the charging cradle.
• The overall charging capacity of the battery is divided into
quarters. Each LED corresponds to a quarter:
• If the battery charge state is low the appropriate LED
flashes slowly.
• The LED flashes faster as the charge state improves.
• If an LED illuminates constantly the battery has reached
the appropriate level of charge.
• When all four LEDs illuminate constantly the battery is
100% charged.
Error LED The red LED illuminates if there is a fault in the electricity supply.
Please refer to "HDS7000 Battery" in "4 Troubleshooting".
Power indicator
LED
The green power indicator LED illuminates if the charging cradle
is under voltage.