Lenz Digital plus LH101 User manual

B.B.10.0040
LH101
Operating Manual
Version 1.0
1st Edition 10 18
Art. no. 21101

2 Operating manual LH101
Welcome!
We would like to congratulate you on your acquisition of the LH101
manual control by Digital plus by Lenz®. We hope you will enjoy this
model railway control.
The LH101 manual control is the universal input device in the
Digital plus by Lenz ®system. With it you can:
- operate your locomotives as well as assemble, operate, and
disassemble multiple tractions
- switch points and signals or enable uncoupling tracks
- read out and configure system settings
- read out information of feedback modules and feedback-capable
switch decoders.
- programme locomotive and switch decoders as well as feedback
modules
The purpose of this operating manual is to explain the use of the
LH101 manual control. To get started, first read the section “First
Steps". Afterwards, you can familiarise yourself, step by step, with the
full range of functions of this manual control and put them to use.
If you still have questions after reading this operating manual, please
contact us. We will be happy to help you. There are four different ways
of contacting Lenz Elektronik GmbH:
Mail address:
Lenz Elektronik GmbH
Vogelsang 14
D-35398 Giessen
Phone:
++49 (0) 6403 900 133
A recorded message will inform
you of our availability
Fax:
++49 (0) 6403 900 155
Email:
[email protected]
All present?
Please check if all components have been delivered:
LH101 manual control
Connecting cable
Operating manual (this booklet)
If any component is missing, please ask your model railway dealer for
a replacement delivery.

Important advice, please read first! 3
Contents
1Important advice, please read first! ......................................................................... 6
2Function overview of the LH101.............................................................................. 8
3First steps..............................................................................................................10
3.1 Connection and initial operation....................................................................10
3.1.1 Connection to the LZ100/LZV100 command station .....................................10
3.1.2 Setting the XpressNET address....................................................................10
3.2 Operating your first train ...............................................................................11
3.2.1 Calling up a locomotive address: ..................................................................11
3.2.2 Controlling a locomotive: ..............................................................................11
3.2.3 Changing the direction of travel: ...................................................................12
3.2.4 Emergency off: .............................................................................................12
3.2.5 Switching the light function of the locomotive decoder:.................................13
4Basic operating instructions for the LH101.............................................................14
4.1 Entering numeric values ...............................................................................14
4.2 Disconnecting and reconnecting the LH100 during operation .......................14
4.3 The LH101 LCD display................................................................................15
4.4 The rotary knob of the LH101 .......................................................................16
5Controlling locomotives..........................................................................................17
5.1 Calling up locomotive addresses ..................................................................17
5.1.1 Entering a new locomotive address using the keypad ..................................17
5.1.2 Choosing locomotive addresses from the “stack” of the LH101 ....................18
5.1.2.1 Scrolling through the stack .......................................................................... 18
5.1.3 Selecting a locomotive address from the command station memory ............19
5.1.4 Taking over control of a locomotive from another manual control .................20
5.2 Changing the locomotive`s speed and direction ...........................................21
5.2.1 Standard mode.............................................................................................21
5.2.1.1 Locomotive-specific emergency stop........................................................... 22
5.2.2 Shunting mode .............................................................................................23
5.3 Enabling functions in locomotive decoders...................................................24
5.3.1 Changing function groups.............................................................................25
5.3.2 Configuring locomotive decoder functions ....................................................25
5.3.3 Configuring the “refresh“ of functions............................................................26
5.4 Displaying and changing the speed-step mode ............................................28
5.5 Emergency off ..............................................................................................29
6Switching points and signals ..................................................................................30
6.1 Displaying the point setting...........................................................................31
6.1.1 Using non-feedback-capable point decoders ................................................31
6.1.2 Using feedback-capable point decoders .......................................................31

4 Operating manual LH101
7Creating, editing and deleting routes ..................................................................... 33
7.1 Creating a new route.................................................................................... 34
7.2 Editing a route.............................................................................................. 35
7.2.1 Editing a step in a route ............................................................................... 37
7.2.2 Deleting a step from a route......................................................................... 38
7.2.3 Adding a step to a route ............................................................................... 39
7.3 Deleting a route............................................................................................ 39
8Setting routes ........................................................................................................ 41
9Double traction ...................................................................................................... 43
9.1 What is a double traction? ........................................................................... 43
9.2 Requirements for a double traction .............................................................. 43
9.3 Assembling two locomotives in a double traction: ........................................ 44
9.4 Assembling locomotives with different speed steps into a double
traction......................................................................................................... 45
9.5 Disassembling a double traction .................................................................. 45
9.6 Error messages when assembling a double traction .................................... 46
10 Multiple traction (MTR) .......................................................................................... 48
10.1 What is a multiple traction?.......................................................................... 48
10.2 Requirements for a multiple traction:............................................................ 48
10.3 Assembling a multiple traction (MTR) .......................................................... 49
10.4 Controlling a multiple traction ....................................................................... 51
10.4.1 Speed and direction of the MTR................................................................... 51
10.4.2 Switching functions in the MTR .................................................................... 52
10.5 Displaying the members of an MTR and switching between locomotives
in an MTR .................................................................................................... 52
10.6 Deleting a locomotive from a multiple traction.............................................. 53
10.7 Deleting a complete MTR............................................................................. 55
10.8 Error messages relating to multiple tractions ............................................... 56
11 Displaying feedback .............................................................................................. 57
12 Configuring (programming) decoder settings......................................................... 59
12.1 What is programming and what purpose does it serve?............................... 59
12.1.1 Difference between "Programming in operational mode" and
"Programming on the programming track" ................................................... 60
12.1.2 When to use “Programming on the programming track”?............................. 61
12.2 Programming in operational mode - PoM..................................................... 62
12.2.1 Which settings can be changed using PoM?................................................ 62
12.2.2 Which locomotive decoders can have their settings changed using
PoM? ........................................................................................................... 62
12.2.3 Programming a numeric value into a CV —step by step approach:............. 62
12.2.4 Reading out CVs using the LRC120 address display ................................... 64

Important advice, please read first! 5
12.2.5 Setting and deleting bits (switches) using PoM —step by step
approach ......................................................................................................65
12.3 Programming on the Programming track ......................................................68
12.3.1 What is a programming track?......................................................................68
12.3.2 Where to connect the programming track/the decoder? ...............................68
12.3.3 Reading out and changing a locomotive address .........................................69
12.3.4 Reading out and programming a CV ............................................................71
12.3.4.1 Binary (bitwise) displaying and changing of the CV value....................... 72
12.4 Error messages while programming on the programming track ....................74
12.4.1 Display of other connected manual controls .................................................74
13 LH101 setup (device setting) .................................................................................75
13.1 Setting the speed step mode ........................................................................75
13.2 Setting the club mode...................................................................................76
13.2.1 Setting club mode 1 or 2...............................................................................77
13.2.2 Setting mode 0 .............................................................................................78
13.3 Counting method for bit representation.........................................................79
13.4 Display brightness ........................................................................................80
13.5 Display contrast............................................................................................82
13.6 Displaying the version number......................................................................83
13.7 Setting the XpressNet address .....................................................................84
13.8 Reset to ex-factory setting ............................................................................85
13.9 Route interval ...............................................................................................86
14 System setup.........................................................................................................88
14.1 Enabling and disabling the "AUTO" mode ....................................................88
14.1.1 System behaviour with "AUTO" mode enabled.............................................89
14.2 Displaying the system version number .........................................................89
14.3 Deleting locomotive addresses from the command station memory .............90
15 Appendix................................................................................................................93
15.1 Error messages on the display .....................................................................93
15.2 Routes form..................................................................................................95
15.3 Trouble shooting...........................................................................................96
15.4 Tree structure of options of the LH101 .........................................................98

6 Operating manual LH101
1 Important advice, please read first!
The LH101 manual control is a component of the Digital plus by Lenz®
system and was submitted to intensive testing before delivery. Lenz
Elektronik GmbH guarantees fault-free operation if you follow the
advice below:
Depending on the command station and the software version used,
certain functions of the LH101 will not be available or only partially
available. Relevant information is contained in the beginning of each
section.
The LH101 may only be operated with Digital plus by Lenz®system
components. Any use other than that described in this operating
manual is not permitted, and all guarantees will become invalid if the
LH101 is used inappropriately.
Connect your LH101 only to devices designated for such connection.
This operating manual will tell you which devices are suitable. Even if
other devices (including those of other manufacturers) are equipped
with the same plug connectors, you must not operate the LH101 with
these devices. The same plug connector does not automatically mean
that operation is permitted. This also applies to other model railway
controls.
Do not expose the LH101 to moisture or direct sunlight.
If you have problems
First check this operation manual to see if you may have missed a
direction for use. The table of contents and especially the section
“Troubleshooting” will help you.
Illustration of step-by-step instructions:
Explanation
In this operating manual, all entries made using the keypad
are shown on the left. On the right you will see what is shown
on the display after the entry has been made.
All steps described assume that the manual control is
connected to a version 3.6 Digital plus by Lenz ®system, and
that this system is turned on.

Important advice, please read first! 7
Illustration of displays and keys in the text:
In most cases, the LH101 display and the keys are shown as
illustrations. If the text makes reference to displays, these are
put in double quotes:
"L 0001"
If the text makes reference to keys, these are put in single
quotes:
'M'
Cross references:
(p. 23)
This arrow refers you to a particular page in this operation
manual, where you will find additional information on a specific
subject.
Important advice:
Text framed and marked with an exclamation mark
contains particularly important information and tips.

8 Operating manual LH101
2 Function overview of the LH101
This section provides a short overview of the functions of the LH101.
The use of these functions is described further below. Cross
references refer you to the corresponding page in this operating
manual.
Display
The LH101 has a large luminous LCD display.
Locomotive addresses
The locomotive address range is 1 to 9999. Address 0 is
used to control an analogue locomotive in the digital
circuit. (p. 17)
Changing speed and
direction
Use the rotary knob to change the locomotive’s speed and
direction. (p. 21)
Stack
8 stack slots for fast selection of locomotive addresses.
Two operating modes
Standard mode:
In this mode (ex-factory setting), use the rotary knob to
decrease the speed step to 0. (p. 21)
Shunting mode:
In this mode, use the rotary knob to decrease the speed
step to 1. Press the rotary knob to stop the locomotive. Let
the locomotive slowly approach the desired location, then
press the rotary knob to stop the locomotive.
The advantage of this mode while shunting: You can
decrease the speed until the locomotive stops without
having to look at the manual control and without risking
that the locomotives stops too early. (p. 23)
Emergency off
Use the emergency off to immediately stop one or all
locomotives. (p. 29)
Switching locomotive
decoder functions
You can access up to 28 functions in locomotive
decoders. (p. 24)
Configuring locomotive
decoder functions
You can set each function of a locomotive decoder to
permanent or temporary operation. (p. 25)
Setting the speed step
mode
Use the LH101 to set the speed steps for the locomotive
address currently displayed. (p. 25)
Double traction (DTR)
Two locomotives are controlled as if they were one. (p.
43)
Multiple traction (MTR)
Several locomotives are controlled with a common
locomotive address. (p. 48)
Switching points and
signals
Use the LH101 manual control to switch up to 1024 points,
signals and other magnetic articles. (p. 30
Routes
You can save up to 16 routes with 16 steps each in the
LH101. (p. 33)
Club modes
The LH101 is capable of two so-called “club modes“ in
which certain functions are blocked. This ensures that
model railway enthusiasts who are not fully familiar with

Function overview of the LH101 9
the LH101 may also join in the fun (p. 76).
Displaying feedback
information
This function of the LH101 manual control allows you to
display the status of the inputs of LR100/101 feedback
modules (p. 57).
Configuring decoder
settings
You can change the address, starting delay, and other
locomotive decoder features through programming. Two
methods are available:
Programming in
operational mode (PoM)
You can configure the settings of your locomotive decoder
while the locomotive is placed anywhere on the layout. For
example, drive your locomotive in front of a heavy freight
train and adjust the starting delay to the train! (p. 62).
Programming on the
programming track
The settings of your locomotive decoder are configured on
a separate programming track (p. 68).
System settings
The LH101 allows you to configure several system
settings. For example, you can configure the behaviour of
the emergency stop button, read out the software version
of your command station, and much more. (p. 88)

10 Operating manual LH101
3 First steps
In this section, you will learn:
- to connect your LH101 to the LZ100/LZV100 command station
- to operate your first train
The sections further below explain all the functions of the LH101 in
detail.
3.1 Connection and initial operation
The LH101 may be connected to the following components of the
Digital plus by Lenz®system:
LZ100 or LZV100 command station from version 3.6 onwards.
As is the case with all XpressNET devices, the LH101 can be
disconnected and reconnected during operation. Use this advantage of
the XpressNet: Mount several LA152 adapter (art. no. 80152) on your
layout. This will enable you to use the LH101 right at the centre of
action.
After connection, the manual
control will display the locomotive
address controlled last. During
initial operation, address 1 will be
displayed.
3.1.1 Connection to the LZ100/LZV100 command station
Plug the 5-pin DIN connector
- into the 5-pin DIN socket at the back of your LZ100/LZV100
or, if you have already installed an XpressNET (XBUS) wiring on
your layout,
- into a LA152 adapter.
3.1.2 Setting the XpressNET address
All input devices connected to the XpressNet (XBUS) must have their
own unique device address for the information exchange with the
command station to function correctly. You must therefore make sure
that all connected devices have different device addresses. Depending
on the command station used, up to 31 devices may be connected to
the XpressNet. Ex-factory, each LH101 manual control is set to