Leviton D3208 User guide

1
Wizards
Menus
8VHAYRU6(/
6(783:,=$5'!
SETUP:
Device type, sound, security and panel selection………4
Configuration and groups for partitioning………………. 6
Zone information, channel & load type…………………. 7
Auxiliary zones……………………………………………..8
8VHAYRU6(/
&/2&.:,=$5'!
SETUP:
Basic Time and Daylight Savings settings………………9
8VHAYRU6(/
=21(:,=$5'!
SETUP:
Minimum levels for each Zone…………………………..16
Lock and Unlock Zones…………………………………. 17
8VHAYRU6(/
6&(1(:,=$5'!
Choose which of 32 Scenes is activated……………….10
Program, name and set fade rate of Scenes…………. 11
Set Scene Bank………………………………………….. 12
Set Scene Group………………………………………….13
Lock out the Scene and Dim/Bright buttons…………...14
Exclude Zones from particular Scenes…………………15
BASIC INFORMATION
AND SETUP PROGRAMMING FOR THE D3208
Checking the Firmware version…………………………18
Specifications……………………………………………… 2
Installation Guide availability.
Backdoor code …………………………………………….3
Table of Contents

2
SPECIFICATIONS
Electrical
Input: 120VAC, 60Hz, +/-10%
Isolated Output: 24 VDC @ 150mA
Power Output: 1920W/VA total
1000W/VA max. per zone (increase capacity with power extender)
1200W/VA max. per side
Minimum Load: 15W
Surge Protection: Surge Suppression for voltage surges up to 6000V and current
surges up to 3000A
Load Types: Incandescent, Tungsten, Magnetic Low-Voltage Transformer,
Advance Mark X Electronic Fluorescent Dimming Ballast, Neon,
Cold Cathode and non-dimming loads.
Testing/Code Compliance: UL Listed, CSA Certified
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device must not
cause harmful interference and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
Real Time Clock: Accurate within 15 seconds per week, with or without power.
Leap year compensation. Calculating of Sunrise and Sunset,
given the correct latitude and longitude, to within 15 minutes.
Environmental
Operating Temperature: 0°C to +40°C
Software
Programmer has been specified with sufficient permanent memory for 20 years
to hold:
- 32 Scenes
- 64 Time schedules

3
I have a customer that has lost or forgotten their password.
!!! CONFIDENTIAL !!!
The backdoor code for the security password is "2757"
The code is typed in using the Scene buttons.
When will the Installation Guide be available?
The Installation Guide is in the process of being completed. Watch for it to
become available @ http://www.leviton.com/d3200/index.html … soon.

4
8VHAYRU6(/
!%DVLF
8VHAYRU6(/
6(783:,=$5'!
(QWHU3DVVZRUG
!
237,2166(7
6(/WR&RQWLQXH
6HOHFW%HHS0RGH
!%HHS2Q!
6HOHFW6W\OH
!$UFKLWHF!
6HOHFW6W\OH
!'HFRUD!
6HOHFW%HHS0RGH
!%HHS2II!
6HOHFW6HFXULW\
!/RFNB2Q!
6HOHFW6HFXULW\
!/RFN2II!
9HULI\3DVVZRUG
!
3$66:25'6(7
6(/WR&RQWLQXH
Select
Next
Select
Next
Select
Next
Select
Next
Select
Next
Select
Next
Select
Next
Select
Next
Select
Next
8VHAYRU6(/
6(783:,=$5'!
Select
Next
Dim/Bright Control :
Decora – general
Architectural – precise
Choice of audible beep
with every button push
or not.
Grant full accessibility
or limit access
to the SCENE buttons.
Key-in a 4-digit
password using the
Scene buttons 1 thru 8.
Repeat the password.
The password leaves the
unit unlocked for 2-1/2
minutes after last action.
Menus for partitioning on next page.
SETUP WIZARD – The first step in setting up the Multizone Controller.
1. Basic – Used to program device style, sound, security and panel selection.

5
SETUP WIZARD
1. Basic
6HOHFW3DQHO
3DQHO
6HW6FHQH0RGH
&20021B6&(1(6!
237,2166(7
6(/WR&RQWLQXH
(GLW3DQHO1DPH
3DQHO
8VHAYRU6(/
6(783:,=$5'!
Select
Next
6HW6FHQH0RGH
',))(56&(1(6!
Select
Next
When using more than one D3208:
Select a unique address (01-31) for this controller.
Up or Down buttons to select panel number.
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.
Select
Next
Select
Next
The following menus help with partitioning and other instances where there is
more than one Multizone Controller.
For Partitioning Only. If not using the partitioning feature, press the Select/Next
button to save entry and proceed.
Note: If using only one Multizone Controller, leave the default setting. Press the
Select/Next button to save entry and proceed.

6
8VHAYRU6(/
6(783:,=$5'!
(GLW1DPH
&21),*
&21),*
6(/(&7
6(/(&7*5283
!
Select
Next
SETUP WIZARD – The first step in setting up the Multizone Controller.
2. Panels – Used to program configuration and group parameters when using the
partitioning. Also setup other panels for remote zone control.
8VHAYRU6(/
!%DVLF Press Down button
1 time.
Select the desired CONFIG (001-256)
This setting will be used to determine the layout of
each room or configuration.
Select
Next
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.
Select
Next
Select the desired Scene Group (01-64) A group is
a collection of zones that is assigned a group
number. A single zone may be in multiple groups.
Select
Next
Up and Down buttons select Panels (01-31)
Right & Left buttons toggle Include or Exclude.
Select
Next
3$1(/
3$1(/,1&/!
(GLW3DQHO1DPH
3DQHO
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.
Select
Next
6(7$8;=21(6
',6!',6!
Up and Down buttons to Enable or Disable the
Auxiliary zones from the panel being programmed.
Right & Left buttons toggle between 1 and 2.
Select
Next
8VHAYRU6(/
!3DQHOV
Select
Next
Wizards
Menu Saves programming and returns to Main Screen.
- OR -

7
8VHAYRU6(/
6(783:,=$5'!
3$1(/=21(
=21(
3$1(/=21(
=21(
6(/(&7*5283
=21(
Select
Next
SETUP WIZARD
3. Zones – Used to program zone information, including zone, group, channel
and device type. A zone can be a single load or group of loads.
8VHAYRU6(/
!%DVLF Press Down button
2 times.
Edit Zone Name using up to 16 characters.
Up and Down buttons scroll A-Z, space and 0-9.
Right & Left buttons move to next/previous space.
Select
Next
Select the Group (01-64) for this zone. Use this
setting to select the group number that this zone
will be assigned to under this configuration.
Select
Next
&+$11(/
=21(
6(/(&77<3(',0
=21(
/2$'7<3(,1&!
=21(
8VHAYRU6(/
!=RQHV
Select
Next
Up and Down buttons to select ZONE (1-8)
Right or Left button for next option.
Up and Down buttons to select PANEL (01-31)
Select
Next
UP and Down buttons scroll CHANNEL (1-8, X)
Change mapping of Channel number to actual Load
connection. No two Channels can have the same
Channel number, so “X” is used as a place holder
until the new number becomes available.
Select
Next
Up or Down button selects TYPE (REL, DIM)
This setting is used to select either a dimming or a
non-dimming Load.
Select
Next Up or Down selects LOAD TYPE (FLOR, INC)
“INC” is for Incandescent, Magnetic Low-Volt,
Cold Cathode, Tungsten and Neon Loads.
“FLOR“ is for Mark X Fluorescent Loads.
Select
Next Wizards Menu Saves programming and returns to Main Screen.
- OR -

8
8VHAYRU6(/
6(783:,=$5'!
6(7$8;'(9,&(
6(/WR&RQWLQXH
3$1(/=21(
=21(
Select
Next
SETUP WIZARD
4. Aux Devices – Used to setup auxiliary zones. Auxiliary zones are loads which
are not directly wired to the D3208 being accessed.
8VHAYRU6(/
!%DVLF Press Down button
3 times.
Select
Next
8VHAYRU6(/
!$X['HYLFHV
Select
Next
Saves programming and returns to Main Screen.
Up or Down buttons to select PANEL (01-31)
Right or Left buttons to select ZONE (1-8)
Select
Next
8VHAYRU6(/
6(783:,=$5'!
(QWHU3DVVZRUG
!
Select
Next
5. System – “The system menu is used only to reprogram the logic board, it has
no other function at this time” – Al Lombardi 6/10/02.
Select
Next
8VHAYRU6(/
!%DVLF Press Down button
4 times.
8VHAYRU6(/
!6\VWHP
NOTE: Reset or Restore Factory Defaults
There is no “reset” function on the D3208. There is also no
way to restore factory defaults from the front panel. There is a
way to restore the factory defaults from a PC using the D3200
software and a smart jack. – Al Lombardi 6/10/02.

9
8VHAYRU6(/
&/2&.:,=$5'!
$GMXVW7LPH
$0
'D\OLJKW6DYLQJ
$XWR$GMXVW21!
Select
Next
CLOCK WIZARD – The second step in setting up the Multizone Controller. It
provides basic Time and Daylight Savings settings. If there are multiple
Controllers on the LCnet, all will synchronize with the first unit programmed.
8VHAYRU6(/
!6HW'DWH7LPH
Right and Left buttons are used to select hour,
minute, second or AM/PM positions.
Up and Down buttons scroll 01-12, 01-59, AM/PM.
After settings are complete, press Select/Next.
Select
Next
Up and Down buttons toggle between ON and OFF.
Set to ON position if Daylight Savings is observed
in your area. Set to OFF to disable the setting.
Select
Next
Select
Next
$GMXVW'DWH
78(
Right and Left buttons are used to select month,
day and year positions.
Up and Down buttons scroll thru each setting.
After settings are complete, press Select/Next.
Select
Next
Press Select/Next to return to the Main Screen.

10
8VHAYRU6(/
!&DOO6FHQH
8VHAYRU6(/
6&(1(:,=$5'!
6&(1(
6HW)DGHGHI!
6HOHFWVFHQH
6&(1(
([HFXWH6FHQH"
6&(1(
Select
Next
Select
Next
Select
Next
SCENE WIZARD – Allows for the programming and operation of up to 32
lighting scenes. Naming of device and lighting scenes gives user-friendly control
of lighting loads.
1. Call Scene – Used to choose which of the 32 programmed scenes are to be
called or activated.
Select the desired scene to call (01-32)
Select
Next
Up or Down button to call the scene with a desired
fade time (default, 0:00 seconds to 2h00m)
Press the Select/Next button to save and proceed.
Select
Next
6FHQH([HFXWHG
6&(1(
Select
Next
8VHAYRU6(/
6&(1(:,=$5'!
Cancel
Previous Returns display to the Main Screen