Leviton DRC Smart Pack User manual

Sense is Normal Power through the supply Input (Black/White): In this scenario, the supply input wires
are connected to normal power, and, the Load In for the relay is connected to Emergency Power. Upon loss
of normal power, the relay closes, and the 0-10V lines go to high impedance allowing the load to go to full
output powered from the Emergency Source. The Emergency Mode switch must be in the LINE position.
Upon restoration of normal power, Smart Pack will automatically resume normal operation.
Distributed Room Controller (DRC) Smart Pack
Cat. No. DRD07
PK-A3148-10-00-2B
• To avoid electrical overload, total connected lamp load shall not exceed output rating.
• To reduce potential shock hazard Cat. No. NPRPT-002 must be installed when more than (2) DRC DRD07-EDO controllers are installed on any
LumaCAN control feed.
• The NPRPT-002 must be grounded to building ground using green wire provided on device.
CAUTIONS
• Test all LumaCAN cables for proper pin-out configuration prior to interconnecting devices and systems.
• Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
• To be installed and/or used in accordance with electrical codes and regulations.
ENGLISH
INSTALLATION AND QUICK START GUIDE
DESCRIPTION
The Distributed Room Controller Smart Pack contains a power supply, 0-10V Dimming Control, LumaCAN
RJ45 input/output and a load switching latching relay. The power supply provides Class 2 low-voltage power
over LumaCAN for powering other devices (Distributed Switch, Occupancy Sensor, Photocell, Sapphire
Touch Controller) as well as monitoring the status of power.
The DRC Smart Pack requires connection to
a LumaCAN network for control, no local control is provided.
The power pack includes zero cross switching
circuitry to minimize inrush current associated with incandescent lights, LED and electronic ballasts,
increasing its life expectancy.
Application Notes:
1. When the total lighting fixtures load exceeds a single power pack’s rating (e.g. 16A Electronic Ballasts),
the load will need to be separated using multiple DRC Smart Packs.
2. When more devices are required than one power pack can supply on the +24V LumaCAN bus, multiple
power packs can be used to supply power to support the additional devices (up to a maximum of 600mA
between two power packs via LumaCAN RJ45 24V output).
Total number of devices attached to a single DRC Smart Pack must be <= 300mA.
Device current requirement (typical):
Sapphire Touch Controller = 600mA (2 DRC's Required)
Digital Switch = 25mA
Photocell = 15mA
Occupancy Sensor = 40mA
WARNINGS
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE
WIRING, SERVICING, OR REMOVING FIXTURE OR CHANGING LAMPS!
• This equipment permits more than one power supply output source. To avoid shock or death, disconnect both normal and emergency sources
connected to this unit before servicing any equipment connected to this unit.
• Do not use outdoors, or near gas or electric heaters.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• "EMERGENCY CIRCUITS" enclosed label should be placed in a highly visible location if any DRC is part of the emergency system so as to be readily
identifiable as a component of the emergency system.
SPECIFICATIONS
Part Number DRD07-ED0
Input Voltage* 120-277VAC, 50/60Hz
Standby Power: 0.62W @ 120V, 1.08W @ 277V
Max Power: 9.30W @ 120V, 9.78W @ 277V
Load Ratings
(120-277VAC)
20A Tungsten
20A General Purpose Plug Load
20A Standard Ballast
16A Electronic Ballast, LED
Motor Ratings 1/2Hp (9.8 FLA) @ 120VAC
2 Hp (12 FLA) @ 240-277VAC
0-10V Control 0.8 - 10+VDC, 100mA Sinking
LumaCAN Power Output +24VDC, 300mA
(will not pass power through, diodes installed on each of the two RJ45’s.
Supply only.)
LumaCAN Data LumaCAN 3 Only
Daisy-Chain Topology
1600 feet max per segment
Repeaters can be used for networks up to 10,000 feet and to support
home-run topology
Max 110 nodes per segment
Max 250 nodes
Connections 18 AWG (Power, 0-10V)
12 AWG (Load IN/OUT)
RJ45, CAT6A or better (LumaCAN)
LED Indicator Yes
Dimensions 4.84" x 4.52" x 1.81"
Weight 0.6 lb (9 oz)
Mounting Standard 4S junction box with minimum volume of 30.3 cu. inches or
greater (4" x 4"x 2.125") using the two (2) provided 8-32 x 2.5" screws.
Or, mounted to junction box via 1/2" nipple.
LumaCAN Connections CAT6A (or better) cable
Operational Temperature 32° to 122º F (0° to 50° C)
Agency Standards and
Certifications
FCC Part 15, Class A
IEC 61000 4-2, 2nd Ed., 12kV Air (ESD)
IEC 61000 4-5, 3rd Ed., 2/4kV (Line Surge)
IP Rating IP30
* Input voltage tolerance 10%, Frequency tolerance 5%.
EMERGENCY
The "Emergency Circuits" label shall be placed on the Smart Pack so the user is aware this device is used
for emergency lighting.
The DRC Smart Pack can be used as a UL 924 emergency bypass device ensuring that the relay is closed
during a power failure condition. Availability of input power to power the load is the responsibility of others. Two
options for sensing normal power are available and your Construction Documents will dictate which you are to
use. The options and features of normal sense are as follows:
• Sense is Normal Power through the Black (Line) wire: Upon loss of supplying power to the device,
relay will close.
• Sense is power over LumaCAN: Upon loss of +24V power on LumaCAN wire, relay will close.
Sense is power over LumaCAN: In this scenario, both the supply input wires AND the Load-In are connected
to the emergency source. The SmartPack monitors power on the LumaCAN line and upon loss of power, the
relay closes and 0-10V lines go to full output. There are two advantages of this mode: 1. LumaCAN remains
operational during the emergency event and can report it’s status to the network, and, 2. Only EM power is run
to the DRC Smart Pack so separation of normal and emergency at this location is not required.
INSTALLATION
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
NOTE: This is an ESD Sensitive Device. Use safe ESD handling procedures when installing.
2. Mount the DRC Smart pack per desired application (see Mounting figure):
a. Mount to junction box using nipple and mounting nut provided.
b. Mount to face of 4S junction box with minimum volume 30.3 cu. inches or greater (4" x 4"x 2.125")
using the two (2) provided 8-32 x 2.5" screws.
• Ensure that conduit/cable entry clamp is located in a corner of junction box opposite the DRC
nipple as conflicts may occur.
• Dress wires to provide enough clearance when device is installed.
3. INSTALLATION NOTE: 0-10V Control Wiring - Connect the Violet wire to the + 0-10V line and the Gray
wire to the 0-10V common using Class 1 or Class 2 wiring methods as indicated in these instructions,
ballast/fixture/driver instructions or ballast/fixture/driver label markings which are in accordance with
NEC Code NFPA 70, paragraph 725.136 (d).
a. For Installation as a Class 1 Device: When this product is installed as a Class 1 device and
configured for use with other Class 1 devices it shall be wired using typical NEC Class 1 requirements.
b. For Installation as a Class 2 Device:
NOTE: Class 2 Installation must be implemented when installing this product.
As required under NEC code NFPA 70, paragraph 725.136 (d), the Class 2 0-10V (gray and violet)
control wires must be mechanically separated from Class 1 wiring (line, neutral and ground power
lines) when located within the same electrical box. This is accomplished by installing a mechanical
barrier such as silicone tubing or other non-conducting sleeve over the length of 0-10V control wires.
Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE. When power is applied, Smart
Pack will power up in the ON state and then default to the last powered down state. The default from the
factory is ON after power up.
Wire Designations
Control Power In: 120-277VAC Black 18 AWG
Control Neutral White 18 AWG
Load (Load IN) Blue/White 12 AWG
Load (Load OUT) Blue 12 AWG
0-10VDC Control Violet 18 AWG
0-10VDC Common Gray 18 AWG
• All wires rated at 105C, 600V insulation.
1. LINE - Black is tied to 120-277VAC Line power (Black incoming line)
2. Neutral - White is tied to incoming Neutral
3. LOAD IN - Blue/White is the input/incoming Load line is tied to incoming "LINE" power. This could be
same wire as #1 or it could be a separate "LINE" power. Perhaps coming from Emergency circuit supply.
Can be 120-277VAC.
4. LOAD OUT - Blue wire. This goes to the device to be powered.
5. The Violet gets connected to the + side of the fixture's 0-10V dimming input and Gray gets connected to
the – side of the fixture's 0-10V dimming input.
LumaCAN LumaCAN
Neutral
Hot
HotWhite
Black
Blue/
White
Neutral
Neutral (white) 0-10V (violet) Com (gray) Hot (blue)
Smart
Pack
To Load
Normal
Panel
Emergency
Panel
4. Line Voltage Wiring: Remove 5/8" (1.6 cm) of insulation from each circuit conductor. Make sure that
ends of conductors are straight. Connect lead wires from DRC Smart Pack to LINE circuit per appropriate
WIRING DIAGRAM as follows: Twist strands of each lead tightly and, with circuit conductors push firmly
into appropriate wire connector. Screw connectors on clockwise making sure that no bare conductor
shows below the wire connectors. Secure each connector with electrical tape.
5. LumaCAN: Two LumaCAN ports are provided to maintain the required Daisy-Chain topology of the
LumaCAN network. Plug in CAT6A (or better) cable with standard RJ45 connector. If two connections
are required, remove the terminator from one of the RJ45’s and make both connections. If only one
connection is required, leave the supplied terminator connected.
• Wire per the TIA-568B standard.
• The sequence of network nodes, as described in the Construction Documents, may be critical to
ensure power distribution between nodes.
• All LumaCAN wire segments must be tested and validated prior to power-up of the system.
• The last device in each LumaCAN run must be terminated using an RJ45 terminator plug. Each
Smart Pack is supplied with one terminator plug pre-installed in the smart pack. Additional terminators
are available upon request. LumaCAN connections must be wired as Class 2 and as such should be
installed according to the requirements of your authorities having jurisdiction. If it is required that the
Class 2 wiring be in conduit, use a 4S extension ring and blank plate on the LumaCAN side of the
Smart Pack, and, terminate conduit to the extension ring.
MOUNTING
a) b)
Nipple
Mounting Screws
1. LumaCAN Port
2. LumaCAN LED - left side of DIP switch
3. Heartbeat/Configuration LED - right side of DIP switch
4. DIP Switches - In middle
5. Emergency Sense Selector Switch - At bottom of tub. (LINE MODE = AWAY from RJ45
CONNECTORS, CAN MODE = CLOSE to RJ45 CONNECTORS)
LED INDICATORS
The LumaCAN LED: Flashes Green whenever there is LumaCAN traffic detected.
Heartbeat LED: See chart below:
Heartbeat LED status in various "failure" states are as follows:
• Processor fails or failed application - RED
- Resolution: Cycle Power. If a power cycle does not restore proper operation, remove LumaCAN
connections and cycle power again. Do not reconnect LumaCAN until after normal operation is
restored.
• Processor in Reset or startup failure - WHITE
- Resolution: Cycle Power. If a power cycle does not restore proper operation, remove LumaCAN
connections and cycle power again. Do not reconnect LumaCAN until after normal operation is
restored.
• Off - Failure
-Resolution: Remove LumaCAN wires. If devices starts up, then there is either an Overcurrent or
Short on the LumaCAN line. Resolve the problem and reconnect.
-Resolution: Check Control Power Input. If Control Power Input is not valid, the device will not
start. Set CAN address to 255 and cycle power to erase application, then reprogram.
OPERATION
3
2
1 1
4
5
Indicator Feature
Blink Rate
(# blinks
per
second)
Duration Possible Causes
Red Duplicate LumaCAN
address
UI Error didn't get
value set in time
External watchdog fail
safe circuit tripped.
2
8
Solid
Until conflict is
resolved
Until 60 seconds or UI
setting restarted
Until watchdog circuit
is no longer tripped
Another LumaCAN device
is using the same address
Took too long to enter
manual information
Application update failure,
hardware failure
White LumaCAN address
on switch matches
current address
Setting LumaCAN
address and verifying
address uniqueness
Device didn’t start, I/O
not initialized
8
Solid
Solid
Until set or timed out
after 10 seconds
Until timed out after
10 seconds
Until problem resolved Hardware failure
Blue Low byte of LumaCAN
channel number is
locked in
Waiting for low byte to
be locked in
8
Solid Until set or timed out
after 60 seconds
Green Normal operating
condition
In boot loader
High byte of
LumaCAN channel
number is locked in
Waiting for high byte
to be locked in
1
4
8
Solid
Until entering actual
application
Single blink
Until set or timed out
after 60 seconds
Application update failure
if alternating with RED
LED.
Off LumaCAN
Overcurrent or failure
––
• If you are not sure about any part of these instructions, consult an electrician.
• Use this device with copper or copper clad wire only.
• DRC & NPRPT-002 devices can be installed in any order.
• Providing this additional ground does not apply when connect to the GreenMAX™ control panel.
SAVE THESE INSTRUCTIONS
LumaCAN LumaCAN
Hot Hot
WH
BLK
BL/WH
WH
BLK
BL/WH
Neutral
Neutral
Neutral (white)
Neutral (white)
0-10V (violet) Com (gray) Hot (blue)
Normal
Lighting
Smart
Pack
To Normal
Lighting Load
Normal
Panel
Emergency
Panel
Emergency
Lighting
Smart
Pack
0-10V (violet) Com (gray) Hot (blue)
To Emergency
Lighting Load
• Notes Specific to this mode:
- The Emergency Mode switch must be in the CAN position
-
The Smart Pack will not provide power to the LumaCAN network. All power must be from
other devices.
- The Systems Designer and Installer must verify that any and all power supplies which
could supply power to either LumaCAN segment are fed from normal power and are not
connected to a UPS or other power source which could be powered in an EM condition.
- SmartPack will go to full output within 1 second.
- Upon restoration of Normal Power, the Smart Pack will automatically resume normal
operation.
• CAN MODE
- Device does NOT supply voltage or power to +24VDC LumaCAN bus
- On loss of +24VDC LumaCAN bus power device will close RELAY and force 0-10V to
MAX brightness
• LINE MODE
- Device supplies 24VDC power to LumaCAN bus to power other devices
- On loss of LINE power the device will close RELAY and force 0-10V to high
impedance (Max brightness)
CAN MODE
(switch in
UP position)
LINE MODE
(switch in
DOWN position)
The CAN Switch
EMERGENCY
Sense Switch
LINE
CAN
EMERGENCY
Sense Switch
LINE
CAN
EMERGENCY
SenseSwitch
LINE
CAN
1. When product is used with 120VAC power source and the 0-10V control wires are connected to CL3,
CL3R or CL3P rated control cables (or permitted substitute), then silicone tubing or other non-conducting
sleeve is required over the control wires for the entire wire length from the device to the location where
the wires exit the box. Tubing is not required on the CL3, CL3R or CL3P between the wire connector and
extending out of the electrical box.
2. When used with 277VAC power source and the 0-10V control wires are connected to CL3, CL3R or
CL3P rated control cables (or permitted substitute), then silicone tubing or other non-conducting sleeve
is required over the control wires for the entire wire length from the device to the location where the
wires exit the box. Tubing is also required on the CL3, CL3R or CL3P between the wire connector and
extending out of the electrical box.
NOTE:
• Silicone tubing should be NRTL (UL/CSA/ETL) recognized or equivalent to provide mechanical separation
equal to .25” in air.
• Connectors joining 0-10V control wires should be approved LISTED CONNECTORS.
• Wire connectors and wire tubing should be provided by the installation contractor.
Hot
0-10V (violet)
Com (gray)
Neutral
(white)
LumaCAN
Hot (blue)
Neutral
BLK
WH
BL/WH Normal
Lighting
Smart
Pack
Normal
Panel
To Normal
Lighting Load
LumaCAN
WEB VERSION

SETTING THE LUMACAN ADDRESS
A unique LumaCAN address ID must be set for each DRC SmartPack. The first 8 switches of the DIP switch
are used for setting the ID. During operation, DIP switches 9 & 10 must be in the off position. Valid node
addresses are 1-250. If the node ID’s are defined in your Contract Document, set to that address.
If not, ensure that the ID is unique for each device in the system. It’s helpful, although not required, that the
location of each node ID is documented for use by Leviton Field service during system commissioning.
To set the node ID, set the DIP switches to the desired ID following the process below:
In case of address conflict, the heartbeat LED will blink Red, twice per second. If this occurs, please clear
the conflict and try again.
SETTING THE STARTING LUMACAN CHANNEL (via DIP Switch)
Setting the channel number requires setting the universe number and the channel number within that
universe. Valid universe numbers are 0-127, resulting in a channel range of 1-32,767. The chart shows each
universe number, the channel range for that universe, the DIP switch setting for the universe, and the actual
channel number.
To set the channel number:
1. Set the Universe Number
a. Turn on DIP Switch P2/10.
i. The LED Indicator should change to solid green indicating that the Smart Pack is awaiting entry of
the universe number.
b. Set DIP switches 1-8 to the required address of the universe number. Refer to the chart.
For channel numbers between 1-256 it will be set to all 0’s.
c. When the address is set, lower DIP switch P2/10.
i. The LED Indicator will start flashing Blue indicating that it is awaiting the channel number.
2. Set the Channel Number
a. Raise DIP Switch P1/9.
i. The LED indicator should go solid blue.
b. Set DIP switches 1-8 to the required address of the channel number. Refer to the chart.
c. Lower dip-switch P1/9.
3. Return DIP switches 1-8 to the desired LumaCAN address.
a. While the addressing is being set, the LED indicator will go solid White. When address is set and
operation restored, the LED will blink green once per second.
NOTES:
If the LED is flashing blue, it means it’s awaiting the channel number. If the LED indicator is flashing green it
indicates it is awaiting the universe number. They can be set in either order but both must be set every time.
TROUBLESHOOTING
Lights are ON after power outage
• This is the normal operation. The power pack has a fail-safe feature which forces the relay to close on
loss of power. Approximately 7-10 seconds after power is restored the device will return to previous state
and continue to monitor LumaCAN bus for any changes.
Device does not operate immediately after power ON
• This is the normal operation. The device has a 7-10 second startup time before it will begin operation.
Lights Flickering
• Lamp has a bad connection.
• Wires not secured firmly with wire connectors.
Lights did not turn ON
• Circuit breaker or fuse has tripped.
• Lamp is burned out.
• Lamp Neutral connection is not wired.
Heartbeat LED is either RED or WHITE
• Represents a processor or application failure. Try power cycling the DRC Smart Pack.
APPLICATION RESET
If your device is "bricked", powering up the device with all dip switches in the on position will cause the
current application to be deleted. Note that this will leave the device in an inoperable state until a software
update is performed.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense. Any changes or modifications not expressly approved by Leviton could void the user’s authority to operate this equipment.
INDUSTRY CANADA COMPLIANCE STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment. This Class A apparatus complies with Canadian ICES-003.
Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the
trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
TECHNICAL SUPPORT
For Technical Support, please contact Leviton Manufacturing at EMCAT[email protected], or [phone].
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is
free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to
correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes
and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or
in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or
not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness
for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this
warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd
to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at
1 800 405-5320.
ID Address Value = Sum of Switch Values
ID 86 = 2+4+16+64
Switch Values
1
2
4
8
16
32
64
128
ID 1
1
ON
2345678
ID 2
1
ON
2345678
ID 3
1
ON
2345678
ID 4
1
ON
2345678
ID 5
1
ON
2345678
ID 6
1
ON
2345678
ID 38
1
ON
2345678
ID 86
1
ON
2345678P1 P2
P1 P2 P1 P2 P1 P2 P1 P2 P1 P2 P1 P2
P1 P2
© 2018 Leviton Mfg. Co., Inc. PK-A3148-10-00-2B
NOTE: In all cases, DIP switches 9 & 10 should be in the off position.
FACTORY DEFAULT
If you desire to return all settings to their factory default position, while the device is powered up, raise dip
switches 1-8 to the ON position (P1 and P2 should remain in their OFF position). The LED will blink yellow
indicating that factory defaults have been restored. Proceed to set the channel number and LumaCAN
address.
Universe
#
Channel
Range
Actual Channel
Range
Universe
Dip
Switch
Setting
Channel Dip Switching Setting
00000000 00000001 00000010 00000011 00000100 … 11111101 11111110 11111111
Start End Actual Channel Number
0 1-255 1 255 00000000 1 1 2 3 4 … 253 254 255
1256-511 256 511 00000001 256 257 258 259 260 … 509 510 511
2 512-767 512 767 00000010 512 513 514 515 516 … 765 766 767
3 768-1023 768 1023 00000011 768 769 770 771 772 … 1021 1022 1023
4 1024-1279 1024 1279 00000100 1024 1025 1026 1027 1028 … 1277 1278 1279
5 1280-1535 1280 1535 00000101 1280 1281 1282 1283 1284 … 1533 1534 1535
6 1536-1791 1536 1791 00000110 1536 1537 1538 1539 1540 … 1789 1790 1791
7 1792-2047 1792 2047 00000111 1792 1793 1794 1795 1796 … 2045 2046 2047
8 2048-2303 2048 2303 00001000 2048 2049 2050 2051 2052 … 2301 2302 2303
9 2304-2559 2304 2559 00001001 2304 2305 2306 2307 2308 … 2557 2558 2559
10 2560-2815 2560 2815 00001010 2560 2561 2562 2563 2564 … 2813 2814 2815
11 2816-3071 2816 3071 00001011 2816 2817 2818 2819 2820 … 3069 3070 3071
12 3072-3327 3072 3327 00001100 3072 3073 3074 3075 3076 … 3325 3326 3327
13 3328-3583 3328 3583 00001101 3328 3329 3330 3331 3332 … 3581 3582 3583
14 3584-3839 3584 3839 00001110 3584 3585 3586 3587 3588 … 3837 3838 3839
15 3840-4095 3840 4095 00001111 3840 3841 3842 3843 3844 … 4093 4094 4095
16 4096-4351 4096 4351 00010000 4096 4097 4098 4099 4100 … 4349 4350 4351
17 4352-4607 4352 4607 00010001 4352 4353 4354 4355 4356 … 4605 4606 4607
18 4608-4863 4608 4863 00010010 4608 4609 4610 4611 4612 … 4861 4862 4863
19 4864-5119 4864 5119 00010011 4864 4865 4866 4867 4868 … 5117 5118 5119
20 5120-5375 5120 5375 00010100 5120 5121 5122 5123 5124 … 5373 5374 5375
21 5376-5631 5376 5631 00010101 5376 5377 5378 5379 5380 … 5629 5630 5631
22 5632-5887 5632 5887 00010110 5632 5633 5634 5635 5636 … 5885 5886 5887
23 5888-6143 5888 6143 00010111 5888 5889 5890 5891 5892 … 6141 6142 6143
24 6144-6399 6144 6399 00011000 6144 6145 6146 6147 6148 … 6397 6398 6399
25 6400-6655 6400 6655 00011001 6400 6401 6402 6403 6404 … 6653 6654 6655
26 6656-6911 6656 6911 00011010 6656 6657 6658 6659 6660 … 6909 6910 6911
27 6912-7167 6912 7167 00011011 6912 6913 6914 6915 6916 … 7165 7166 7167
28 7168-7423 7168 7423 00011100 7168 7169 7170 7171 7172 … 7421 7422 7423
29 7424-7679 7424 7679 00011101 7424 7425 7426 7427 7428 … 7677 7678 7679
30 7680-7935 7680 7935 00011110 7680 7681 7682 7683 7684 … 7933 7934 7935
31 7936-8191 7936 8191 00011111 7936 7937 7938 7939 7940 … 8189 8190 8191
32 8192-8447 8192 8447 00100000 8192 8193 8194 8195 8196 … 8445 8446 8447
33 8448-8703 8448 8703 00100001 8448 8449 8450 8451 8452 … 8701 8702 8703
34 8704-8959 8704 8959 00100010 8704 8705 8706 8707 8708 … 8957 8958 8959
35 8960-9215 8960 9215 00100011 8960 8961 8962 8963 8964 … 9213 9214 9215
36 9216-9471 9216 9471 00100100 9216 9217 9218 9219 9220 … 9469 9470 9471
37 9472-9727 9472 9727 00100101 9472 9473 9474 9475 9476 … 9725 9726 9727
38 9728-9983 9728 9983 00100110 9728 9729 9730 9731 9732 … 9981 9982 9983
39 9984-10239 9984 10239 00100111 9984 9985 9986 9987 9988 … 10237 10238 10239
40 10240-10495 10240 10495 00101000 10240 10241 10242 10243 10244 … 10493 10494 10495
41 10496-10751 10496 10751 00101001 10496 10497 10498 10499 10500 … 10749 10750 10751
42 10752-11007 10752 11007 00101010 10752 10753 10754 10755 10756 … 11005 11006 11007
43 11008-11263 11008 11263 00101011 11008 11009 11010 11011 11012 … 11261 11262 11263
44 11264-11519 11264 11519 00101100 11264 11265 11266 11267 11268 … 11517 11518 11519
45 11520-11775 11520 11775 00101101 11520 11521 11522 11523 11524 … 11773 11774 11775
46 11776-12031 11776 12031 00101110 11776 11777 11778 11779 11780 … 12029 12030 12031
47 12032-12287 12032 12287 00101111 12032 12033 12034 12035 12036 … 12285 12286 12287
48 12288-12543 12288 12543 00110000 12288 12289 12290 12291 12292 … 12541 12542 12543
49 12544-12799 12544 12799 00110001 12544 12545 12546 12547 12548 … 12797 12798 12799
50 12800-13055 12800 13055 00110010 12800 12801 12802 12803 12804 … 13053 13054 13055
51 13056-13311 13056 13311 00110011 13056 13057 13058 13059 13060 … 13309 13310 13311
52 13312-13567 13312 13567 00110100 13312 13313 13314 13315 13316 … 13565 13566 13567
53 13568-13823 13568 13823 00110101 13568 13569 13570 13571 13572 … 13821 13822 13823
54 13824-14079 13824 14079 00110110 13824 13825 13826 13827 13828 … 14077 14078 14079
55 14080-14335 14080 14335 00110111 14080 14081 14082 14083 14084 … 14333 14334 14335
56 14336-14591 14336 14591 00111000 14336 14337 14338 14339 14340 … 14589 14590 14591
57 14592-14847 14592 14847 00111001 14592 14593 14594 14595 14596 … 14845 14846 14847
58 14848-15103 14848 15103 00111010 14848 14849 14850 14851 14852 … 15101 15102 15103
59 15104-15359 15104 15359 00111011 15104 15105 15106 15107 15108 … 15357 15358 15359
60 15360-15615 15360 15615 00111100 15360 15361 15362 15363 15364 … 15613 15614 15615
61 15616-15871 15616 15871 00111101 15616 15617 15618 15619 15620 … 15869 15870 15871
62 15872-16127 15872 16127 00111110 15872 15873 15874 15875 15876 … 16125 16126 16127
63 16128-16383 16128 16383 00111111 16128 16129 16130 16131 16132 … 16381 16382 16383
64 16384-16639 16384 16639 01000000 16384 16385 16386 16387 16388 … 16637 16638 16639
65 16640-16895 16640 16895 01000001 16640 16641 16642 16643 16644 … 16893 16894 16895
66 16896-17151 16896 17151 01000010 16896 16897 16898 16899 16900 … 17149 17150 17151
67 17152-17407 17152 17407 01000011 17152 17153 17154 17155 17156 … 17405 17406 17407
68 17408-17663 17408 17663 01000100 17408 17409 17410 17411 17412 … 17661 17662 17663
69 17664-17919 17664 17919 01000101 17664 17665 17666 17667 17668 … 17917 17918 17919
70 17920-18175 17920 18175 01000110 17920 17921 17922 17923 17924 … 18173 18174 18175
71 18176-18431 18176 18431 01000111 18176 18177 18178 18179 18180 … 18429 18430 18431
72 18432-18687 18432 18687 01001000 18432 18433 18434 18435 18436 … 18685 18686 18687
73 18688-18943 18688 18943 01001001 18688 18689 18690 18691 18692 … 18941 18942 18943
74 18944-19199 18944 19199 01001010 18944 18945 18946 18947 18948 … 19197 19198 19199
75 19200-19455 19200 19455 01001011 19200 19201 19202 19203 19204 … 19453 19454 19455
76 19456-19711 19456 19711 01001100 19456 19457 19458 19459 19460 … 19709 19710 19711
77 19712-19967 19712 19967 01001101 19712 19713 19714 19715 19716 … 19965 19966 19967
78 19968-20223 19968 20223 01001110 19968 19969 19970 19971 19972 … 20221 20222 20223
79 20224-20479 20224 20479 01001111 20224 20225 20226 20227 20228 … 20477 20478 20479
Universe
#
Channel
Range
Actual Channel
Range
Universe
Dip
Switch
Setting
Channel Dip Switching Setting
00000000 00000001 00000010 00000011 00000100 … 11111101 11111110 11111111
Start End Actual Channel Number
80 20480-20735 20480 20735 01010000 20480 20481 20482 20483 20484 … 20733 20734 20735
81 20736-20991 20736 20991 01010001 20736 20737 20738 20739 20740 … 20989 20990 20991
82 20992-21247 20992 21247 01010010 20992 20993 20994 20995 20996 … 21245 21246 21247
83 21248-21503 21248 21503 01010011 21248 21249 21250 21251 21252 … 21501 21502 21503
84 21504-21759 21504 21759 01010100 21504 21505 21506 21507 21508 … 21757 21758 21759
85 21760-22015 21760 22015 01010101 21760 21761 21762 21763 21764 … 22013 22014 22015
86 22016-22271 22016 22271 01010110 22016 22017 22018 22019 22020 … 22269 22270 22271
87 22272-22527 22272 22527 01010111 22272 22273 22274 22275 22276 … 22525 22526 22527
88 22528-22783 22528 22783 01011000 22528 22529 22530 22531 22532 … 22781 22782 22783
89 22784-23039 22784 23039 01011001 22784 22785 22786 22787 22788 … 23037 23038 23039
90 23040-23295 23040 23295 01011010 23040 23041 23042 23043 23044 … 23293 23294 23295
91 23296-23551 23296 23551 01011011 23296 23297 23298 23299 23300 … 23549 23550 23551
92 23552-23807 23552 23807 01011100 23552 23553 23554 23555 23556 … 23805 23806 23807
93 23808-24063 23808 24063 01011101 23808 23809 23810 23811 23812 … 24061 24062 24063
94 24064-24319 24064 24319 01011110 24064 24065 24066 24067 24068 … 24317 24318 24319
95 24320-24575 24320 24575 01011111 24320 24321 24322 24323 24324 … 24573 24574 24575
96 24576-24831 24576 24831 01100000 24576 24577 24578 24579 24580 … 24829 24830 24831
97 24832-25087 24832 25087 01100001 24832 24833 24834 24835 24836 … 25085 25086 25087
98 25088-25343 25088 25343 01100010 25088 25089 25090 25091 25092 … 25341 25342 25343
99 25344-25599 25344 25599 01100011 25344 25345 25346 25347 25348 … 25597 25598 25599
100 25600-25855 25600 25855 01100100 25600 25601 25602 25603 25604 … 25853 25854 25855
101 25856-26111 25856 26111 01100101 25856 25857 25858 25859 25860 … 26109 26110 26111
102 26112-26367 26112 26367 01100110 26112 26113 26114 26115 26116 … 26365 26366 26367
103 26368-26623 26368 26623 01100111 26368 26369 26370 26371 26372 … 26621 26622 26623
104 26624-26879 26624 26879 01101000 26624 26625 26626 26627 26628 … 26877 26878 26879
105 26880-27135 26880 27135 01101001 26880 26881 26882 26883 26884 … 27133 27134 27135
106 27136-27391 27136 27391 01101010 27136 27137 27138 27139 27140 … 27389 27390 27391
107 27392-27647 27392 27647 01101011 27392 27393 27394 27395 27396 … 27645 27646 27647
108 27648-27903 27648 27903 01101100 27648 27649 27650 27651 27652 … 27901 27902 27903
109 27904-28159 27904 28159 01101101 27904 27905 27906 27907 27908 … 28157 28158 28159
110 28160-28415 28160 28415 01101110 28160 28161 28162 28163 28164 … 28413 28414 28415
111 28416-28671 28416 28671 01101111 28416 28417 28418 28419 28420 … 28669 28670 28671
112 28672-28927 28672 28927 01110000 28672 28673 28674 28675 28676 … 28925 28926 28927
113 28928-29183 28928 29183 01110001 28928 28929 28930 28931 28932 … 29181 29182 29183
114 29184-29439 29184 29439 01110010 29184 29185 29186 29187 29188 … 29437 29438 29439
115 29440-29695 29440 29695 01110011 29440 29441 29442 29443 29444 … 29693 29694 29695
116 29696-29951 29696 29951 01110100 29696 29697 29698 29699 29700 … 29949 29950 29951
117 29952-30207 29952 30207 01110101 29952 29953 29954 29955 29956 … 30205 30206 30207
118 30208-30463 30208 30463 01110110 30208 30209 30210 30211 30212 … 30461 30462 30463
119 30464-30719 30464 30719 01110111 30464 30465 30466 30467 30468 … 30717 30718 30719
120 30720-30975 30720 30975 01111000 30720 30721 30722 30723 30724 … 30973 30974 30975
121 30976-31231 30976 31231 01111001 30976 30977 30978 30979 30980 … 31229 31230 31231
122 31232-31487 31232 31487 01111010 31232 31233 31234 31235 31236 … 31485 31486 31487
123 31488-31743 31488 31743 01111011 31488 31489 31490 31491 31492 … 31741 31742 31743
124 31744-31999 31744 31999 01111100 31744 31745 31746 31747 31748 … 31997 31998 31999
125 32000-32255 32000 32255 01111101 32000 32001 32002 32003 32004 … 32253 32254 32255
126 32256-32511 32256 32511 01111110 32256 32257 32258 32259 32260 … 32509 32510 32511
127 32512-32767 32512 32767 01111111 32512 32513 32514 32515 32516 … 32765 32766 32767
WEB VERSION