Leviton Vizia RF RZP03-1LW User manual

NOTES:
• If using a non-Leviton Programmer/Remote,
refer to the Programmer/Remote instruction
sheet for Including a device.
A) If using a Leviton Z-WaveTM Programmer/
Remote, Cat. No. RZCPG, press the Menu
button and scroll down to System Setup.
Press the center button to select System
Setup Menu. Press the center button to select
Network.
Scene Capable Plug-In Lamp Dimming Module
Cat. No. RZP Ø 3-1LW
Rated: 120VAC, 60Hz
Incandescent: 300W max., 60W min.
INSTALLATION INSTRUCTIONS
DI-000-RZP03-00C
INTRODUCTION
Leviton’s ViziaTM RF components are designed
to communicate with each other via Radio
Frequency (RF) to provide remote control
of your lighting. Using RF technology allows
Leviton to provide the greatest signal integrity
possible. Each module in Leviton’s ViziaTM
RF component line is a Z-WaveTM enabled
device. In a Z-WaveTM network, each device is
designed to act as a router. These routers will
re-transmit the RF signal from one device to
another until the intended device is reached.
This ensures that the signal is received by its
intended device by routing the signal around
obstacles and radio dead spots. The Scene
Capable Plug-in Lamp Dimming Module
is compatible with any Z-Wave™ enabled
network, regardless of the manufacturer and
can also be used with other devices displaying
the Z-Wave™ logo.
CAUTION:
Remember to exercise good common sense
when using the Timer features of your remote,
especially when scheduling unattended
devices. There can be some unexpected
consequences if not used with care. For
example, an empty coffee pot can be remotely
turned on. If that should happen, your coffee
pot could be damaged from overheating. If an
electric heater is turned on by remote control
while clothing is draped over it, a fire could
result. DO NOT USE the remote for the control
of high power heating appliances such as
portable heaters. This device will not control
lighting that is used with electronic low-voltage
and high frequency power supply transformers,
nor high pressure discharge lamps (HID
lighting). This includes mercury-vapor, sodium
vapor and metal halide lamps. DO NOT change
location after unit is enrolled in Z-waveTM
network.
Including Scene Capable
Plug-In Lamp Dimming Module
into Z-Wave
TM
Network:
Step 3
Attaching Scene Capable
Plug-In Lamp Dimming
Module to Wall Receptacle:
Step 2
• Plug the Plug-in Dimmer Module into wall
receptacle. Verify that receptacle is live. If
controlled by a wall switch, the switch
must be kept ON at all times.
Attaching Load to Scene
Capable Plug-In Lamp
Dimming Module:
Step 1
NOTE: In order to use your ViziaTM Scene
Capable Lamp Dimming Module in a Z-WaveTM
network, it must be Included into the network
using a Primary Programmer/Remote, such as
Leviton’s Cat. No., RZCPG. Before Including your
module, please refer to the Primary Programmer/
Remote instruction sheet for complete
information. Refer to Step 3 for further details.
• Locate lamp to be controlled by Scene
Capable Plug-In Lamp Dimming Module and
ensure it is fully operational. Attach lamp plug
into module receptacle noting proper polarity of
blades.
NOTE: Use check boxes when Steps are
completed.
INSTALLING YOUR DIMMING MODULE
B) While standing close to the module
(approximately 2-5 ft.), press the center
button to <Include> device in the network.
NOTE: Only one device may be included
at a time. DO NOT put multiple devices into
the Inclusion mode at any time.
C) While the Programmer/Remote is in the
Inclusion mode and the LED is ON on the
Scene Capable Plug-In Lamp Dimming
Module, press the ON/OFF button on the
module. The Programmer/Remote will verify
inclusion and the LED will turn OFF on the
Scene Capable Plug-In Lamp Dimming
Module.
If the Scene Capable Plug-In Lamp
Dimming Module is flashing Amber while
in the Inclusion mode, the Programmer/
Remote is still trying to communicate with
the Scene Capable Plug-In Lamp Dimming
Module. Wait until the device stops flashing,
then press ON/OFF button.
NOTE: If the LED on the Scene Capable
Plug-In Lamp Dimming Module turns
solid Red while including, there has
been a communication error. Refer to
Troubleshooting section.
D) The Primary Programmer/Remote will
assign a node ID number (Name) for this
module.
NOTE: This ID number (Name) will be
stored in the controller to be used for future
reference.
NOTE: You may name or edit the node of
this device at this time.
E) The module is now installed in the
network.
NOTE: If the module has been successfully
Included in the network and the user tries to
Include it again without
first excluding it from the
network, the module will
retain the first node ID it
had received and ignore
the second.
WARNINGS AND CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• To reduce the risk of overheating and possible damage to other equipment do not install to control a
motor-operated appliance, fluorescent lighting fixture, or a transformer supplied appliance.
WARNINGS AND CAUTIONS:
• Unplug unit when servicing connected lighting fixtures.
• Save this instruction sheet. It contains important technical data along with testing
and troubleshooting information which will be useful after installation is complete.
• Soft fade ON/OFF
• Scene capable
• ON/OFF LED
• Two way communication
• Manual ON capability at load
• RF reliability
• Ease of installation – No new wiring
• Compatible with other Z-Wave™ enabled devices
FEATURES
Step 2 cont’d Step 3 cont’d
Programming and
ON/OFF Button
1 ON
2 ON
3 ON
4 ON
OFF
OFF
OFF
OFF
Programmer/Remote
Cat. No. RZCPG
Center Button
Menu Button
Compatible with enabled products!
TM

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the
purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton
Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation.
This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any
labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such
implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or
loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
OPERATION
NOTE: For complete details on operating the
Primary Programmer/Remote, refer to the
individual device’s instruction guide.
ON: This command will BRIGHTEN the lights to
the last level set.
OFF: This command will DIM the lights to OFF.
BRIGHTEN: This command will BRIGHTEN the
lights to the desired level.
DIM: This command will DIM the lights to the
desired level.
MANUAL ON: If Scene Capable Plug-In Lamp
Dimming Module is OFF, turn the switch located
on the controlled lamp OFF for a few seconds,
then ON again. The module will turn the lamp
ON to full BRIGHT. This procedure can be
used to turn ON the lamp without accessing the
transmitter.
NOTE: If a power interruption should occur while
the device is ON, the light load will return to its
previous state when power is restored.
NOTE: The Scene Capable Plug-In Lamp
Dimming Module can control the Load before
being included in the Z-WaveTM network. After
powering up module, wait 10 seconds, then press
the Programming ON/OFF button to turn the Load
ON or OFF.
If the Scene Capable Plug-In Lamp Dimming
Module appears to be functioning improperly,
proceed with the following steps:
1. Confirm that the device is being supplied from
a 120V, 60Hz AC source ONLY.
2. Confirm that the Load being controlled is in
proper working order (local switch is ON) and
check for burned-out bulbs.
3. Confirm that the load being controlled does not
exceed the 300W module limit.
4. Confirm that the unit is programmed properly.
Repeat “INSTALLING YOUR DIMMING
MODULE” section to verify that it has been
included into Z-WaveTM network.
TROUBLESHOOTING
DI-000-RZP03-00C
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.ViziaRF.com
Protected under U.S. Patent Number 6,388,399
and patents pending and licensed under U.S.
Patents Numbers 5,905,442, and 5,982,103
NOTE: It is very important to accurately
Exclude devices from the network when
moving or removing a device from a Z-WaveTM
network. This ensures that all information has
been removed from your Primary Programmer/
Remote’s information table and is not counted
on to be a part of the mesh network.
A) If using a Leviton Z-WaveTM Programmer/
Remote, Cat. No. RZCPG, press the Menu
button and scroll down to System Setup.
Press the center button to select System
Setup Menu. Press the center button to
select Network.
B) While standing close to the module, press
the center button to <Exclude> device from
the network.
NOTE: Only one device may be excluded at
a time.
C) While the Programmer/Remote is in the
Exclusion mode and the LED is ON on the
Scene Capable Plug-In Lamp Dimming
Module, press the ON/OFF button on the
module. The Programmer/Remote will verify
Exclusion and the LED will turn OFF on
the Scene Capable Plug-In Lamp Dimming
Module.
If the Scene Capable Plug-In Lamp Dimming
Module is flashing Amber while in the
Exclusion mode, the Programmer/Remote is
still trying to communicate with the module.
Wait until the device stops flashing, then
press the ON/OFF button.
Excluding Plug-In Lamp
Dimming Module from
Network:
Step 4
This equipment has been tested and found
to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment OFF and ON,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving Antenna.
• Increase the separation between the
equipment and the receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
tv technician for help.
FCC COMPLIANCE STATEMENT
Factory Default:
If your module is not responding, or you are
unable to control it after you have tried to Include/
Exclude it multiple times, it may be necessary to
reset the module to its original factory settings. To
accomplish this, proceed as follows:
• Unplug the module and wait 5 seconds. Plug
the module back in and within 20 seconds
press and hold the programming button until
the LED flashes Amber and turns solid Red.
The module is now reset. Once the module is
reset, it will be necessary to Re-Include it to a
network before it can be used.
CAUTION: SETTING A DEVICE TO A
FACTORY DEFAULT DOES NOT EXCLUDE
THAT DEVICE FROM A NETWORK. THE
EXCLUSION PROCEDURE MUST STILL BE
FOLLOWED TO REMOVE THE DEVICE FROM
THE PRIMARY REMOTE’S INFORMATION
TABLE. FAILURE TO DO SO MAY RESULT IN
SYSTEM THAT IS SLOW TO RESPOND, OR
MAY FAIL TO RESPOND TO SOME DEVICES.
Wall Receptacle
Lamp Plug
Scene Capable Plug-In
Lamp Dimming Module
NOTE: Programmer/Controller must be in close
proximity to Scene Capable Plug-In Lamp
Dimming Module when including into network
RZCPG Programmer/
Controller
OUT OF NETWORK OPERATION:
ON: Press the button on the Scene Plug-In Lamp
Dimming Module to turn the lights from OFF to
ON.
NOTE: The lights will turn ON full BRIGHT
regardless of the last level set.
OFF: Press the ON/OFF button to turn the lights
from ON to OFF.
BRIGHTEN: Press and hold the ON/OFF button
to BRIGHTEN the lights to the desired level.
DIM: Press and hold the ON/OFF button to DIM
the lights to the desired level.
Including Scene
Capable Plug-In
Lamp Dimming
Module into
Z-WaveTM Network:
Step 3 cont’d Step 4 cont’d
Press ON/OFF Button