Leviton decora IP710-LF User manual

Fluorescent and LED Fixture Slide Dimmer
Single Pole (One location) or 3-Way (Multi-location)
Cat. No. IP710-LF
1200VA-120VAC, 60Hz, 1500VA-277VAC, 60Hz
For Use with LED fixtures using 0-10V dimmable power supply/drivers,
Advance Transformer Mark 7®OSRAM Sylvania Quicktronic®Helios™ or equivalent dimmable ballasts.
IMPORTANT: For 3-way applications, note that one of the
screw terminals from the old switch being removed will usually
be a different color (Black) or labeled Common. Tag that wire
with electrical tape and identify as the common (Line or Load)
in both the dimmer wall box and the standard 3-way switch
wall box.The remaining two wires on the brass or lighter screw
terminals of the old switch are the travelers.
Step 1
NOTE: If the wiring in the wall box does not resemble any of
these configurations, consult an electrician.
Identifying your wiring application
(most common):
WARNINGS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING OR
SERVICING FIXTURE!
• To avoid overheating and possible damage to this device and other equipment, use only with the appropriate LED 0-10V dimmable power supplies/drivers,
Advance Transformer 120/277V Mark 7®0-10V ballasts or OSRAM Sylvania Quicktronic®Helios™ electronic ballasts.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
CAUTIONS:
• If you are unsure about any part of these instructions, consult an electrician.
• Use only one (1) dimmer in a 3- or 4-way circuit. The switch(es) will turn the light on at the brightness level selected at the dimmer.
• Lighting fixture and dimmer must be grounded.
• Use this device only with copper or copper clad wire.
• To avoid damage to the product, DO NOT use disinfecting products, including foggers, sprays or other types of atomized cleaning agents.
• DO NOT spray liquid onto the product.
• To clean use a damp cloth with mild soap. DI-221-IP710-01A
Tools needed to install your Dimmer
• Slotted/Philips Screwdriver
• Pliers
• Pencil
• Electrical Tape
• Ruler
• Cutters
Installing Dimmer by itself or with other devices
If installing Dimmer in a single device application, proceed
with the INSTALLING YOUR DIMMER section. If installing
Dimmer in a multi-device application, proceed as follows:
Your Dimmer includes three color options. The Dimmer
ships with the White frame attached. To change color of
frame, proceed as follows:
Changing the color of your Dimmer
Push in side at tab
to release
Line up tabs and
press in side to attach
Note: Move slider on dimmer and slider on change kit
to bottom of the slide bar prior to engaging.
MULTI-DEVICE APPLICATION:
NOTE: You only need to remove side sections if installing
with other dimmers or if it does not fit in wall box – not
when installing with mechanical switches.
When installing more than one dimmer in the same
location, the side sections of the mounting strap must be
removed. Use pliers to carefully bend side sections back
and forth until they break off.
Bend back and
forth to remove side section
Remove
all inner
side
sections
Do not
remove
outer
side
sections
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power is
off before wiring!
Note: No derating is required in this mult-device
installation as referenced in the following chart.
MAXIMUM BULB WATTAGE:
0-10VDC ballasts are rated in Volt-Amps (VA). The maximum
number of ballast per dimmer is based on the load VA rating.
The maximum bulb wattage is determined by the efficiency of
the ballast.
NOTE: For additional switching capacity, use dimmers in
conjuction with a Leviton OPP20 120/277V Power Pack.
For applications using Leviton's OPP20 Power Pack
(Shown in Wiring Diagrams 2 & 4), the OPP20 switch
ratings are as follows (refer to OPP20 Instruction Sheet
for additional information):
OPP20 SWITCH RATINGS:
20 Amps for 120 and 277 VAC Ballast
0-10 VDC Sink Current Rating:
28 mA maximum sink current. Contact your ballast
manufacturer for the sink current consumption of the ballast.
INSTALLING YOUR DIMMER Step 3A
Step 2 Preparing wires:
• Pull off pre-cut insulation from Dimmer leads.
• Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove 5/8" (1.6 cm) of insulation from each wire in the wall
box (shown).
•For Single-Pole Application, go to Step 4A.
• For 3-Way Application, go to Step 4B.
Strip Gage
5/8"
(1.6 cm)
Cut
(if necessary)
Strip 5/8"
(1.6 cm)
Insert wires straight
then twist clockwise
Electrical Tape
Neutral
Ground
Black
Red
Pink
Violet
Green
Red
This wire is used in 3-way installations only.
For single pole installations, do not remove this
insulating label.
Single-Pole Wiring Application:
•Green dimmer Ground lead to Green or bare copper wire in
wall box.
• Black dimmer lead to Line Hot wall box wire.
• Red dimmer lead without insulating label to Load wall box wire.
• Remaining Red dimmer lead should have Red insulation
label affixed.
NOTE: If insulating label is not affixed to Red lead, use a small
wire nut or electrical tape to cap off.
• Violet dimmer lead to (+) Violet connection on ballast.
• Pink dimmer lead to (-) Pink or (-) Gray connection on ballast.
• Proceed to Step 4.
Connect wires per WIRING DIAGRAM 1
(shown on page 2) as follows:
Screw wire connectors on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
NOTE: Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will house
the IP710 Dimmer.
Step 3B
Neutral
Ground
Black
Red
Pink
Violet
Green
Red
•Green dimmer Ground lead to Green or bare copper wire in
wall box.
• Black dimmer lead to tagged (common) wall box wire
identified in step 2.
• Remove Red insulating label from Red lead.
• First Traveler wall box wire identified in step 2 to any red
dimmer lead.
• Second Traveler wall box wire identified in step 2 to the
remaining red dimmer lead.
• Violet dimmer lead to (+) Violet connection on ballast.
• Pink dimmer lead to (-) Pink or (-) Gray connection on
ballast.
• Proceed to Step 4.
3-Way Wiring Application:
Connect wires per WIRING DIAGRAM 3
(shown on page 2) as follows:
Screw wire connectors on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
NOTES:
• Dimmer can be installed on either the Load or Line side.
• Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will
house the IP710 Dimmer.
• For additional switching capacity, use dimmers in
conjuction with a Leviton OPP20 120/277V Power Pack.
Insert wires straight then
twist clockwise
Electrical Tape
NOTES:
• Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will house
the IP710 Dimmer.
• For additional switching capacity, use dimmers in conjuction
with a Leviton OPP20 120/277V Power Pack.
Single Pole
1. Line (Hot)
2. Neutral
3. Ground
4. Load
5. Pink (-) or Gray (-)
6. Violet (+)
3-Way
1. Load (See note below)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
6. Pink (-) or Gray (-)
7. Violet (+)
3
2
1
6
7
4
5
3
1
4
5
6
2
INSTALLATION INSTRUCTIONS ENGLISH
MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE
Cat. No. Volts Single Two Gang More than
2 Devices
IP710-LF 120 1200VA 1200VA 1200VA
IP710-LF 277 1500VA 1500VA 1500VA
WEB VERSION

© 2022 Leviton Mfg. Co., Inc.
Patents covering this product, if any, can be found on Leviton.com/patents.
Step 6
Step 4
Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
• Restore power at circuit breaker
or fuse.
• Carefully holding Dimmer as
shown, move slider control lever to
highest position. Lights should turn
ON to brightest level. If lights do
not turn ON, depress push-button
switch once. Lights should turn ON
to brightest level.
If lights still do not
turn ON, refer to the
TROUBLESHOOTING section.
Installation may now be completed by carefully positioning
all wires to provide room in wall box for dimmer.
Mount dimmer into box with mounting screws supplied.
Attach wallplate.
Testing your Dimmer prior to mounting in
wall box:
Step 5 Dimmer Mounting:
TURN OFF POWER AT CIRCUIT BREAKER
OR FUSE.
OPERATION
ON/OFF:
Depress push-button switch to ON
position - Lights will turn ON.
Depress push-button switch to OFF
position - Lights will turn OFF.
BRIGHTEN & DIM:
Move slider control lever -
Lights will BRIGHTEN or DIM.
NOTE: If using the dimmer in a 3-way application, the lights
will turn ON at brightness set on dimmer's slide control lever.
The lights can be controlled from either the dimmer or the
switch location.
Wiring Diagram 1 : Single Location Control
Hot (Black)
Neutral (White)
To Additional Ballasts
Dimmer
Line
120/277VAC,
60Hz
To Lamps
0-10 VDC
Ballast
Black
White
Yellow
Red
Blue
Primary
Side
Green
Ground
Red
Black
Red
Pink or Gray
Violet
Pink
Violet
Insulating
Label
Wiring Diagram 2 : Single Location Control with OPP20 Power Pack
Dimmer
Green
Ground
Red
Insulating
Label
Yellow
Pink or Gray
Violet
0-10 VDC
Ballast
Red
0-10 VDC
Ballast
Primary
Side
Black
To Additional
Ballasts
To Lamps
Red
White
Black
White
Pink or Gray
Violet
Blue
To Additional Ballasts
Line
120/277 VAC,
60Hz
Black
Yellow
To Lamps
Red
Blue
Blue
White
Yellow/Orange
Blue
Black
Red
White/Blue
Blue
Black
Pink or Gray
OPP20
Primary
Side
Blue
White
Yellow/Orange
Blue
Black
Red
White/Blue
Blue
Black
Pink or Gray
OPP20
Hot (Black) circuit #2
Neutral (White)
Hot (Black)
NOTE: Leviton OPP20 Power Pack shown, wire colors can vary on other Power Packs. NOTE: Power Pack and the load switched by the power pack MUST be fed from the same phase.
Pink
Violet
Wiring Diagram 3: Two Location Control
Hot (Black)
Neutral (White)
To Additional Ballasts
Dimmer
Line
120/277VAC,
60Hz
3-Way Switch
To Lamps
Black Screw
(common)
0-10 VDC
Ballast
Black
White
Yellow
Red
Blue
Primary
Side
Green
Ground
Green
Ground
Red
Red
Black
Pink or Gray
Violet
Pink
Violet
Wiring Diagram 4: Two Location Control with OPP20 Power Pack
Hot (Black)
Neutral (White)
To Additional Ballasts
Dimmer
Line
120/277VAC,
60Hz
3-Way Switch
To Lamps
Black Screw
(common)
0-10 VDC
Ballast
Black
White
Yellow
Red
Blue
NOTE: Leviton OPP20 Power Pack shown, wire colors can vary on other Power Packs. NOTE: Power Pack and the load switched by the power pack MUST be fed from the same phase.
Primary
Side
Blue
White
Yellow/Orange
Blue
Black
Red
White/Blue
Blue
Black
Pink or Gray
OPP20
Green
Ground
Green
Ground
Red
Red
Black
Pink or Gray
Violet
Pink
Violet
Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only,
are/may be the trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
TROUBLESHOOTING
For non-standard wiring applications,
refer to Wire Connector Size Chart below.
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly with wire connectors.
• Light does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
NOTE: If further information is needed in identifying the
HOT wire in a 3-Way application, go to Leviton's website at
www.leviton.com.
Setting the Maximum Light Level
This dimmer features a Maximum Trim
adjustment to adjust the maximum light
level of the dimmer when the slide is at
its highest position.
1. Locate the "Trim Adjustment" dial on
the top of the dimmer.
2. Rotate the dial clockwise to reduce
the maximum light level, or counter-
clockwise to increase the maximum
light level.
Trim
Adjustment Dial
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is
free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to
correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes
and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or
in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or
not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness
for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this
warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada
ULC to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
1- #12 w/ 1 to 3 #14, #16 or #18
2- #12 w/ 1 or 2 #16 or #18
1- #14 w/ 1 to 4 #16 or #18
2- #14 w/ 1 to 3 #16 or #18
WEB VERSION