LG LW6015ER User manual

OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your air conditioner and retain it for future reference.
P/NO MFL68763202
www.lgappliances.com
TYPE WINDOW
MODEL LW6015ER

Before Operation
7
16
19
Safety Precautions
Introduction
Electrical Safety
Installation
Operating Instructions
Maintenance and Service

Do not store flammables like
gasoline benzene thinner
etc. near the air conditioner.

No correlation between fan
usage and oxygen depletion.
Unplug the unit when not
using it for a long time.

For inner cleaning, contact an Authorized Service Center or a dealer.
Do not use harsh detergent that causes corrosion or damage on the unit.
Harsh detergent may also cause failure of product, fire, or electric shock.
Hold the plug by the head
it out.
（not
the cable） when taking
Never touch the metal parts
of the unit when removing
the filter.
Install the product so the exhaust and noise
are not aimed directly at the neighbors.
When gas leaks, open the
window for ventilation before
operating the unit.
Be considerate.
Follow installation instructions exactly.

y
If you eat the liquid from the battery,brush
your teeth and see doctor.Do not use the
remote if the battery has leaked.
y
Do not use this appliance for
special purposes such as
cooling pets
foods，
precision
machinery， or objects of art
，
You will feel better.
Instead of running air conditioning
constantly
，open
a window
for fresh air occasionally.
You will feel better.
If the liquid from the battery gets onto your skin
or clothers，
wash it well with clean water. Do
not use the remote if the battery has leaked.

2. No correlation between fan usage and oxygen depletion.
3.

RESET
TEST
9
should be
Avoid shock hazard. This unit cannot
be user-serviced. Do NOT open the
tamper-resistant sealed portion.
All warranties and performance will
be voided. This unit is not intended
to be used as an ON/OFF switch.

10

Left Guide Panel
Right Guide Panel
Curtain
Phillips head
screwdriver
Scissors or
knife
11
(10mm)
2/5″
(16mm)
5/8″

12
(Type D)
drawing
in the drawing.
Size
Clearance

upper and bottom guide.
with 4 screws (Type A) on each side.
13
Bottom Guide
Left Guide panel
Right Guide
panel
(Type A)
Screws
Curtain
Attatch L bracket (Type D)

1-1. Set the air conditioner in the window
so that is centered. Place the air
conditioner so that front edge of the
bottom guide is against the back
edge of the sill.
4
(Type B) to
1-2. Bring the window down so that the
front edge of the upper guide is in
front of the window. Make sure that
air conditioner is level or tilting
slightly to the outside.
CAUTION
To prevent broken glass or
damage to windows, on vinyl or
other similarly constructed
windows, attach the window
locking bracket to the window
side jamb with one Type A screw.
Bracket
Bottom Guide
14
Install the air conditioner in the window
Secure the guide panels (Type G)
Install the sash seal and sash lock
secure them.

15
3-4
3-3.
Remove the screw from the right
side of cabinet.
(Type H)
Window installation of room air conditioner is now completed.
See ELECTRICAL DATA for attaching power cord to electrical outlet.

16
POWER
Operation starts when this button is pressed and stops when you
press the button again.
- when the air conditioner is off,it can be set to automatically turn
Delay OFF
- when the air conditioner is on,it can be set to automatically turn
on from 1 to 24 hours at its previous mode and fan settings.
off from 1 to 24 hours.
Delay ON
ON/OFF TIMER
FAN SPEED SELECTOR
Use to set the fan speed to Low (F1), MED (F2), High (F3).
OPERATION MODE SELECTOR
Push the MODE button to rotate between Energy Saver / Cool / Fan / Dry.
Approximately every 3 minutes the fan will turn on and check the room air
Energy Saver - The fan stops when the compressor stops cooling.
temperature if cooling is needed.

17
During operation in failure of electric power, the unit runs as previous setting operation.
y
Do not use rechargeable battery. Make sure that the battery is new.
Do not mix alkaline, standard (Carbon-zinc) or rechargeable (Nickel-cadmium)
batteries.
- In order to prevent discharge, remove the battery from the remote control if
the air conditioner is not going to be used for an extended period of time.
To maintain optimal operation of the remote control, the remote sensor should
not be exposed to direct sunlight.
Keep the remote control away from extremely hot or humid places.
1. Push out the cover on the back of the remote control with your thumb.
2. Pay attention to polarity and insert one new AAA 1.5V battery.
3. Reattach the cover.
Once the set temperature is reached， the compressor and circulation fan turns off.
Dry - Dry mode is used to remove humidity from the room without additional cooling.
Fan speed is pre-set and cannot be adjusted.
TEMPERATURE CONTROL
The thermostat monitors room temperature to maintain the desired temperature.
The thermostat can be set between 60
F~86 F (16 C~30 C).
FILTER RESET
‘Clean Filter’ LED will light up to notify you that your filter needs to be cleaned.
After cleaning the filter, press ‘Filter Reset’ button to turn off ‘ Clean Filter’ light.
Cool -
Compressor runs and cools the room. Use the
and FAN buttons to
set the desired temperature and circulation fan speed.
the desired fan speed.
Fan
-
Fan circulates air but compressor does not run. Use the FAN button to set
The unit defaults to Energy Saver mode each time the unit is switched on except
restoration after an electrical power outage and fan mode.
ENERGY SAVER
This feature is reminder to clean the Air Filter (See Maintenance) for more efficient operation.
The LED (light) will illuminate after 250 hours of operation.

drain
base pan
base pan
18
Slinger Fan

Inlet Grille
19
1. Pull the inlet grille forward.
2. Remove the air filter from the front grille by pulling the air filter up slightly.
3. Wash the filter using lukewarm water below 40
4.Gently shake the excess water from the filter and replace.

call 1-800-243-0000.
20
an outlet of the proper
voltage and amperage.
Water drip from the rear of the unit
Normal Sound
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Unit may vibrate and
make noise because of poor
wall or window construction
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
“Gurgling or hissing” noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.（See
the section on Slinger Fan, page 18)
High pitched Chatter
Gurgle/Hiss
Pinging or Swishing
or incorrect installation.
Vibration
Sound of Rushing Air