Life Span EX2 User manual

NOTE: This manual may be subject to updates or changes. Up to date manuals are available through our website at www.lifespanfitness.com.au
Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
EX-2 EXERCISE BIKE
OWNER’S MANUAL

2
EX-2
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. CARE INSTRUCTIONS 4
3. EXPLODED DIAGRAM 5
4. PARTS LIST 6
5. ASSEMBLY INSTRUCTIONS 7
6. TENSION ADJUSTMENT 12
7. EXERCISE MONITOR INSTRUCTIONS 14
8. WARRANTY 16

3
EX-2
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this machine.
It is important your machine receives regular maintenance to prolong its useful life. Failing to
regularly maintain your machine may void your warranty.
Please keep this manual with you at all times
a. It is important to read this entire manual before assembling and using the equipment. Safe and
effective use can only be achieved if the equipment is assembled, maintained and used properly.
Please note: It is your responsibility to ensure that all users of the equipment are informed of all
warnings and precautions.
b. Before starting any exercise program you should consult your doctor to determine if you have any
medical or physical conditions that could put your health and safety at risk, or prevent you from
using the equipment properly. Your doctor’s advice is essential if you are taking medication that
affects your heart rate, blood pressure or cholesterol level.
c. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, and extreme shortness of breath, lightheadedness, dizziness or feelings of nausea. If
you do experience any of these symptoms, you should consult your doctor before continuing with
your exercise program.
d. Keep children and pets away from the equipment. This equipment is designed for adult use only.
e. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the equipment should have at least 2 meters of free space around it.
f. Before using the equipment, check that the nuts and bolts are securely tightened. If you hear any
unusual noises coming from the equipment during use and assembly, stop immediately. Do not use
the equipment until the problem has been rectified.

4
EX-2
g. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may get
caught in the equipment or that may restrict or prevent movement.
h. This equipment is designed for indoor and family use only
i. Care must be taken when lifting or moving the equipment so as not to injure your back.
j. Always keep this instruction manual and assembly tools at hand for reference.
k. The equipment is not suitable for therapeutic use.
2. CARE INSTRUCTIONS
a. Maximum use weight: 100KG
b. Lubricate moving joints with grease after periods of usage
c. Be careful not to damage plastic or metal parts of the machine with heavy or sharp objects
d. The machine can be kept clean by wiping it down using dry cloth
Battery Usage
a. Batteries are to be installed or replaced by adult only
b. Do not use rechargeable batteries. Do not mix different battery types. Do not mix old and new
batteries. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries
c. Remove batteries when product is not in use
d. Remove exhausted batteries from product and dispose of in accordance with the manufacturer’s
recommendation
e. Do not attempt to recharge non-rechargeable batteries
f. Batteries are to be inserted with correct polarity
g. The supply terminals are not to be short-circuited
h. Do not dispose of batteries in fire, batteries may explode or leak

5
EX-2
3. EXPLODED DIAGRAM

6
EX-2
4. PARTS LIST
No.
Description
QTY
NO.
Description
QTY
1
Main frame
1
39
Chain cover screw ST4.2X40
3
2
Front stabilizer
1
40
Screw ST4.8×20
1
3
Rear stabilizer
1
41
Flat washer D8x3xΦ38
2
4L/R
Coupler bar
2
42
Arc washer Φ10×1.5×Φ25×R28
4
5
Square cap
2
43
Hexagon bolt M8x20
2
6L/R
Pedal tube
2
44
Hexagon bolt M10×45
4
7L/R
Handle bar
2
45
Nylon nut M10
6
8L/R
Chain cover
2
46
Carriage bolt M10×57
4
9
Fan wheel
1
47
Acorn nut M10
4
10
Square cap
2
48L/R
Nylon nut B0.5×20
2
11L/R
Pedal
2
49
Chain cover screw ST4.8X30
4
12
Handle bar shaft
1 50
Computer
1
13
End cap
4 51
Spring washer Φ13×B2
2
14
Foam grip
4 52
Spring washer Φ10.5×3×Φ18
2
15
End cap Φ25×2
10
53
Gear
1
16
Plastic bushing
4 54
Chain wheel
1
17
Knob bolt
4 55
Washer
1
18
Transport wheel
2 56
D shape washer Φ28×Φ16.2×14×B5
2
19
Alloy bushingΦ24×16×Φ16.1
10 57
Bolt M10×18
2
20
Alloy bushingΦ14×10×Φ10.1
4 58
Pulse sensor wire
2
21
Brass bushing
2 59
Hexagon bolt M6×45
2
22
Fan wheel axle
1
60
Nylon nut M6
2
23
Nut M10×1×B5
4
61
Hexagon bolt M10×55
2
24
Adjusting bolt M6×36
2
62L/R
Pedal hinge bolt Φ16×89×L23×B0.5×20
2
25
Nut M10×1
2
63
End cap Φ32×1.5
2
26
Sensor
1
64
Screw M4X12
2
27
Crank
1
65
Saddle
1
28
Connecting tube
2
66
Flat washer D8
3
29
Washer
1
67
Nylon nut M8
3
30L
Collar housing L
1
68
Saddle post
1
30R
Collar housing R
1
69
Decorative sleeve
1
31
Collar ball
2
70
Tri-knob
1
32
Collar housing
2
71
Cap S13
4
33
Nut
1
72
Computer post
1
34
Chain
1
73
Flat washer D5
2
35
Tension belt
1
74
Cap S16
4
36
Tension control
1
75
Cap S18
2
37
Upper computer wire
1
76
Washer
1
38
Chain cover screw十ST4.2X20
2

7
EX-2
5. ASSEMBLY INSTRUCTIONS
NOTE:
Most of the listed assembly hardware has been packaged separately, but some hardware items have
been preinstalled in the identified assembly parts. In these instances, simply remove and reinstall the
hardware as assembly is required.
Please reference the individual assembly steps and make note of all preinstalled hardware.
STEP 1:
Install the Stabilizers
1. Attach the Stabilizers (2&3) onto the
Main frame (1), secure with the
Carriage bolts (46), Arc washers
(42), and Acorn nuts (47).
Notice that the Front stabilizer (2) has
wheels for moving your Elliptical bike.

8
EX-2
STEP 2:
Install the Coupler bars & Pedal arms
1. Remove Washer (76),D shape washer (56), Spring washer (52) and Bolts (57) from the
Handle bar shaft (12) on one side, mount one Coupler bar (4Ror4L) to the Main section, then
attach the other side Coupler bar (4Ror4L), and reinstall the D shape washer (56), Spring
washer (52) and Bolts (57) as shown.
2. Fit the Pedal tubes (6) to the Crank (27), secure with the Pedal hinge bolts (62R/L), Spring
washers (51) and Nylon nuts (48). And cover with caps (75)
Note: Both Pedals hinge bolts are labelled L FOR LEFT and R FOR RIGHT. To tighten turn the left
bolt COUNTERCLOCKWISE and the right bolt CLOCKWISE. Move the Crank to a proper angle for
easily tightening the Bolts.

9
EX-2
Install the Handle bars
1. Insert the Handle bars (7L&7R) to the Coupler bars
(4R/L) accordingly, select a comfortable height for
exercise, and make sure both Handle bars are at a
same level. Lock in place with Knob bolts(17).And cover
with the cap(71)
ATTENTION:
The Right and Left Hinge Bolt (No.62R/L) must fully penetrate the
nylon ring inside the Pedal Arm Joint and the Crank. This will ensure
the stability and durability of your Elliptical Trainer.
In order to install hinge bolt properly, keep it perfectly straight as the
bolt goes through the pedal arms and the crankshaft. If the hinge bolt is
connected to the crankshaft at an angle, damage to both the hinge and
the crankshaft may occur.
STEP 3:
STEP 4:
Install the Pedals
1. Attach the Pedals (11) to the Pedal
tubes (6) respectively, secure in
place with the Hexagon bolts (44)
and Nylon nuts (45).

10
EX-2
Install the Saddle and Saddle post
1. Place the Saddle (65) over the Saddle post (68), secure in place with the Flat washers (66)
and Nylon nuts (67).
2. Slide the Decorative Sleeve (69) onto the Saddle post, then insert the Saddle post into the
Main section; adjust to a proper position, secure in place with the Tri-knob (70).
STEP 5:
STEP 6:
1.
Connecting tubes (28) to the Main section,
secure in place with Knob bolts(17).Fix the
Computer post (72) onto the Connecting tubes
(28), secure with Flat washers (41) and
Hexagon bolts (43). Cover the Bolts with Caps
(71).Check and re-fasten the Knob bolts (17).
Connect the Wires (26 & 37) ,Then insert the

11
EX-2
STEP 7:
Install the Computer
1. Connect the Wires (58 & 37) to the
Computer (50) respectively; secure the
Computer onto the Bracket with the Flat
washers (73) and Screw (64).

12
EX-2
6. TENSION ADJUSTMENT
Tension adjustment
The assembly of your Elliptical Trainer is now complete. As you try your exercises for the first time, you
should adjust the tension to the correct level before you begin your full workout. Turning the adjustment
knob allows you to change the tension level and vary the intensity of your workout as you exercise.
To increase tension turn the tension knob to the clockwise and to decrease tension turn the tension knob
counterclockwise.
Adjusting the friction belt
You can loosen or tighten the friction belt
for greater tension adjustment.
Turn the tension adjustment knob all the
way to the loosest setting.Then re-strap the
friction belt at the buckle in the main frame
which just beneath the flat beam at the top
centre.The more length you allow for the
friction belt to wrap around the fan wheel.
the less friction it will cause.Re-adjust the
tension knob after you finished re-strapping
Friction Belt Buckle
Friction Belt
Tension
Adjustment Knob
The more tightly the
friction belt wraps
around the fan wheel,
the harder it is
for you to pedal
(more tension)

13
EX-2
Reversible movement
Your Elliptical Trainer has REVERSIBLE movement!
Forward pedaling exercises your quadriceps (front thigh muscles), while backward pedaling targets your
hamstrings (back thigh muscles). Take advantage of these facts to make your workout less fatiguing and
more fun.
CAUTION: MAKE SURE YOU HAVE TIGHTENED ALL NUTS AND BOLTS BEFORE BEGINNING
YOUR WORKOUT

14
EX-2
7. EXERCISE MONITOR INSTRUCTIONS
FUNCTIONAL BUTTONS:
MODE - Push down to select functions. Hold down to reset values to 0.
SET - Sets the values of time, distance, pulse and calories when not in scan mode.
RESET - Push down to reset time, distance and calories. The current data change is 0. If the long time
holds down RESET, besides the ODO position, the material will turn completely 0.
FUNCTION AND OPERATIONS:
1. SCAN: Press “MODE” button until “SCAN” appears. The display will rotate through all the 4 functions
a) Time, speed, distance, calorie, ODO and pulse. Each display will be show for 4 seconds.
2. TIME:
a) Counts the total time from exercise start to end.
b) Press “MODE” button until “TIME” appears, press “SET” button to set exercise time. When the
“SET” time reaches zero, the computer will beep for 5 seconds.
3. SPEED: Display current speed.
4. DIST:
a) Counts the distance from exercise start to end.
b) Press “MODE” button until “DIST” appears, Press “SET” button to set exercise distance. When
the “SET” reaches zero, the computer will beep 5 seconds.
5. CALORIES:
a) Counts the total calories from exercise start to end.
b) Press “MODE” button until “CAL” appears, Press “SET” button to set exercise calories. When
the “SET” is zero, the computer will alarm 5 seconds.
6. ODO: The total distance which this function is refers for the entire battery capacity period.

15
EX-2
7. PULSE RATE:
Press MODE button until “PULSE” appears. Before measuring your pulse rate, place your palms of
your hands on both contact pads and the monitor will show an estimate of your current heart beat rate
in beats per minute (BPM) on the LCD after 6 ～7 seconds.
Note: During the process of pulse measurement, the measurement may be higher than the virtual pulse
rate during the first 2～3 seconds. After this it will return to normal levels. The measurement value
cannot be regarded as the basis of medical treatment.
8. ALARM: The computer will “Beep” when pressing “MODE”, “SET” and “RESET” buttons.
9. AUTO ON/OFF ＆ AUTO START/STOP:
Without any activity for 8 minutes, the power will turn off automatically. The display will turn on once it
senses activity on the machine.
SPECIFICATIONS:
FUNCTION
Auto Scan Every 4 seconds
Running Time 00:00-99:59
Current speed 0.0～999.9 KM
Trip Distance 0.0～999.9 KM
Total distance(ODO) 0.0～999.9 KM
Calories 0.0～999.9 Kcal
Pulse Rate 40～240BPM
Battery type 2 pcs of size - AA or UM - 3
Operating temperature: 0℃～＋40℃
Storage temperature: -10℃～+60℃

16
EX-2
8. WARRANTY
AUSTRALIAN CONSUMER LAW
Many of our products come with a guarantee or warranty from the manufacturer. In addition, they come with
guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. Full details of your consumer rights may be found at
www.consumerlaw.gov.au
Please visit our website to view our full warranty terms and conditions:
http://www.lifespanfitness.com.au/warranty-repairs
Warranty and Support:
Please email us at [e-mail] for all warranty or support issues.
For all warranty or support related enquiries an email must be sent before contacting us via any other
means.
Head Office and Customer Service:
Global Fitness and Leisure Pty Ltd
17 Fordson Rd
Campbellfield
VIC, 3061
Australia
PH: 03 9357 2166

17
EX-2
Hand Pulse Technology
Lifespan Fitness products come equipped with hand pulse sensors which are used to pick up tiny EKG/ECG
signals that run through the body when your heart beats. These electrical EKG/ECG signals are very small and
that they must be amplified 1000 times to make the signal useful for the computer to display your pulse.
To ensure proper operation:
-The user must maintain good, consistent contact on all four sensors
-The users skin cannot be too dry or too wet
Other factors that could affect the reading:
-Change of grip on the sensors (during slow pace cycling and up to sprinting)
-Tightening of hand muscles will produce small electrical signals
-Static electricity charges from the air or from moving on the spin bike
EKG/ECG Sensors may filter through actual EKG/ECG signals and “Noise” factors that may affect the reading.
This will cause the pulse reading to be delayed and will take longer to update the display as the heart rate
changes. Too much noise will create an incorrect reading. Medical conditions or having no electrical signal in the
hands are other factors that may affect pulse readings as well.
These are limitations of hand pulse technology and even the most expensive systems (which can cost upwards
of $3,000) used in hospitals have the same problems. The difference is that a patient in a hospital is not pedaling
on a spin bike.
To test if your hand pulse sensors are working up to specification, hold them while stationary, not pedaling, and
see if the reading is more in line with what you would expect. This will eliminate the movement and static
electricity factors. If your hands are dry, then wet them slightly (saliva works as a great conductor if this doesn’t
bother you).
For more information, please contact our Lifespan Technical Support Department
www.lifespanfitness.com.au
[e-mail]