Lightmybricks LEGO Corner Garage 10264 User manual

The following page is the instructions for the Light My Bricks LEGO Corner
Garage (10264) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Corner Garage (10264) LED light
Light My Bricks: LEGO Corner Garage 10264
Lighting Kit

kit , please click here to view the product page
Package Contents:
10x White 15cm Bit Lights
4x White 30cm Bit Lights
3x Pink 30cm Bit Lights
1x Blue 30cm Bit Light
1x LEGO Lamp Post with Bit Light installed
8x White Strip Lights
1x 6-Port Expansion Board
1x 8-Port Expansion Board
1x 12-Port Expansion Board
7x 15cm Connecting Cable
3x 30cm Connecting Cables
1x USB Power Cable
1x Micro Battery Pack (requires 3x LR44 Batteries)
6x Adhesive Squares
LEGO Pieces:
2x Trans Clear Round Plate 1×1
2x Trans Red Round Plate 1×1
6x Plate 1×6 (Any Colour)
2x Black Round Plate 1×1 with Open Stud
2x Black Tile 1×1 with Clip Rounded Edges
2x Black 1×1 Modified Plate Rounded with Handle

Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side

with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.
Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.
OK, Let’s Begin!
Lighting up the Truck
1.) The first thing we will do is light up the truck. First take this vehicle and
remove the following pieces from the front, then disassemble as per below:

2.) Take a White 15cm Bit Light and thread the connector side of the cable
through the front of the light grey technic pin. Thread it all the way through,
then carefully bend the Bit Light on a 90 degree angle so that it is sitting flat
against the edge of the pin. Take a provided Trans Clear Round Plate 1×1and
connect it over the top.

Repeat this step to install another White 15cm Bit Light to the other technic
pin, securing it in place using another provided Trans Clear Round Plate 1×1.

3.) Remove the following sections from the front of the truck,then thread one of
the Bit Light cables through the front of the below piece allowing you to
reconnect the left headlight.

Disconnect the wheel, then reconnect the left headlight section ensuring the
cable is passed through over the wheel axis, before reconnecting the wheel
over the top.
4.) Repeat previous step to reconnect the right headlight to the truck then
reconnect the remaining sections we removed earlier.

5.) Turn the truck around and disconnect the back section as well as rear right
wheel, then thread the cable from the right headlight up the space in front of
the rear right wheel (which leads to the back of the truck). Ensure the cable is
pulled up inside the black side rail as per below images.