Lightolier Lytespan ATTACHMENT User manual

I
(
A.
B.
c.
D.
INSTRUCTIONS FOR LYTESPAN ATTACHMENT FITTING
INSTRUCTION SHEET NO
lS:7589AZ
ROW
/- SILVERED CONTACT
CORD PENDANT MOUNTING
(supports up to 10 Ibs.)
I. Unscrew LEVER. Remove PLUG ASSEMBLY, HOUSING
INSERT from attachment HOUSING. See Fig. 1.
2. See “WIRING PROCEDURE” below.
STEM MOUNTING USING 1/2” O.D. TUBING
(supports up to 25 Ibs.)
I. Unscrew LEVER, STRAIN RELIEF CAP and KNURLED
RING Remove PLUG ASSEMBLY, HOUSING INSERT
from attachment HOUSING.
2. Use STEM TUBING with M-18 pipe thread
3A” long (not supplied). Screw KNURLED RING onto
STEM TUBING. See Fig. 1A.
3. Insert STEM TUBING into attachment
HOUSING and screw on LOCKNUT until secure.
Tighten KNURLED RING to lock in place.
4. See “WIRING PROCEDURE’’ below.
CHAIN MOUNTING
(supports up to 25 Ibs..)
1. Unscrew LEVER and STRAIN RELIEF CAP.
Remove PLUG ASSEMBLY, HOUSING INSERT from
attachment HOUSING.
2. Replace STRAIN RELIEF CAP with %-18 CHAIN LOOP
(not supplied). See Fig. lB.
3. See “WIRING PROCEDURE” below.
WIRING PROCEDURE
1.
2.
3.
4.
5.
Remove 2“ of outer insulation from FIXTURE CORD
(when required) and strip conductor ends 3A”. See Fig. 1.
Insert FIXTURE CORD through attachment housing.
Fasten BLACK WIRE to LONGER (BRASS) CONTACT and
WHITE WIRE to SHORTER (SILVERED) contact. For
3conductor cord, splice GROUND LEADS with wire
connector. (If the GROUND LEAD from the attachment
HOUSING is not used, leave wire connector on.) See Fig. t
CAUTION: OBSERVE POLARITY WHEN
FASTENING WIRES. BEND WIRES AROUND
SCREW IN CLOCKWISE DIRECTION.
Pull FIXTURE CORD back through attachment HOUSING and
push HOUSING INSERT and PLUG ASSEMBLY into
HOUSING (silvered contact in PLUG ASSEMBLY facing
grooved side of attachment HOUSING). Push ground leads
into area between SPRING section. Fig. 2.
Allow fixture cord to extend into attachment HOUSING by
1/6” and tighten PLASTIC SET SCREW, Fig. 2.
CAUTION: TIGHTEN ENOUGH TO SUPPORT
ASSEMBLY.
Screw LEVER into PLUG ASSEMBLY.
‘RASSCoNTACT----kc <
f
‘“~ :::~;
,SJQ/
GREEN GROUND !
1
“~F’=
LEAD
\
>;, PLUG ASSEMBLY
$3 “~i
w,,,-’”
CONNECTOR
‘REEN ‘ROuND --=&
LEAD
KNURLED RING
STRAIN RELIEF
CAP
$3W27 /’-LEvER
—
SET SCREW
~~,xTuRE
CORD
FIG. 1
KNURLED
RING
*
CHAIN s<
LOOP
8
KNURLED
(by others)
~sT~~
TUBING
STEM
MOUNTING CHAIN
MOUNTING
GROOVE
LEVER
TIC SET
FIXTURE
CORD --’4 l\ SCREW
~ ~ > STRAIN RELIEF
CAP
FIG. 2
‘@ SECAUCUS, NEW JERSEY, 07096 ”0508
[m[<>[=[~<>[ml[~l~ MONTREAL, QUEBEC, CANAD~

~$js~RucT[~Ns FOR ATTACHING LyTEspA/IJ
ATTACHMENT FITTING
1. Align BEAD on LYTESPAN TRACK and GROOVE
in attachment FITTING before inserting into
LYTESPAN TRACK. See Fig.1 (If BEAD is NOT
aligned, apotential hazard may result.)
2. Unscrew the TURN KNOB partially and
position LEVER as shown in Fig. 1.
3. To attach attachment FITTING:
squeeze BUTTON and TURN KNOB,
insert into LYTESPAN TRACK, and
release. Tighten TURN KNOB. This
holds attachment FITTING to LYTESPAN
TRACK mechanically. Turn LEVER to make
electrical connection. See Fig. 2.
4. To shift fixture location on the LYTESPAN
TRACK loosen TURN KNOB slightly, release
LEVER and slide to new position.
5. To remove fixture reverse the procedure in (3),
push TURN KNOB in and allow attachment
FITTING to disengage.
6. Fixture can be left on LYTESPAN TRACK
when not in use by turning LEVER to
disconnect electrically.
INSTRUCTIONS FOR CONVERTING LYTESPAN
ATTACHMENT FITTING TO OPERATE ON (2 CIRCUIT)
LYTESPAN TRACK.
NOTE: To insure proper operation of Lytespots on Two Circuit
Lytespan Track, the BLACK SPACER
(supplied) must be used at all times on the PIU9
assembly.
The BLACK SPACER is not used when operating
Lytespots on Single Circuit Track.
LOWER CIRCUIT, FIG. 3:
Illustrates contacts in low position with spacer
in place for lower circuit.
UPPER CIRCUIT, FIG. 4 and 5:
To convert attachment fitting for upper circuit,
raise BRASS CONTACT to high position (as
indicated by dotted line) by pulling CONTACT
as high as stop permits and slipping on BLACK
SPACER as shown in Fig. 4 and 5.
_LYTESPAN TRACK
BEAO ER
BUTTON
GROOVE NG
FIG. 1
I
(
BUTTON ~
FIG. 2
BLACK SPACER
MOVABLE BRASS
CONTACT
o
FIG. 3
MOVABLE BRASS
%
CONTACT
STATIONARY SILVEREO
BLACK CONTACT (COMMGN)
SPACER PLUG
b
.ASSEMBLY
-5”” \
II
BLACK
6
SPACER
0
FIG. 4FIG. 5