Lightolier a Genlyte company www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2007 Genlyte Group LLC • I0507
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lytecaster®Recessed Downlighting 1004ICX
Page 1 of 1 5" Aperture 0®High Wattage Incandescent AirSeal Insulated Ceiling Frame-In Kit
Features
1. Housing: .032" (#20 ga.) aluminum. UL listed for direct contact with thermal
insulation. AirSeal®housing minimizes air leak-age to less than 2 CFM
at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces
heat loss and condensation in ceiling. Access door for inspection of junction
box.
2. Mounting Frame: .032 (#22ga.) galvanized steel. Accommodates ceilings
up to 1" thick. 3/8" deep integral lip. Locks into position along length of
mounting bars with locking screw and bendable slot. Four slots are posi-
tioned 90° apart to simplify alignment. Push-in/twist-out roto-clips hold
reflector flush to ceiling.
3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in.) .032" (#22 ga.) galvanized steel.
UL listed for maximum of 6 (#12 ga.) 90°C through branch circuit conductors.
Integral cable clamps permit attachment of non-metallic (#12 or #14 ga.)
Romex®cable without tools or additional connectors.
4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy attach-
ment and wire-in below ceiling line. Bars extend to accommodate 16" to 24"
O.C. joist spacing. Bars can accommodate 12" O.C. joist spacing after a slight
field modification (see Instruction Sheet). 1004ICX features integral self tap-
ping phillips screws for secure attachment to wood or metal construction.
1004ICXN features integral nails for secure attachment to wood. Both attach
to T-bar ceilings without the need of accessories.
5. Socket Housing: Impact extruded aluminum or galvanized steel.
6. Socket: Porcelain medium base; nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 Volt 200° C) leads to junction box.
7. Thermal Protector: Meets NEC and UL requirements. Located inside
housing
Options & Accessories
Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4" to 2" thick ceilings
Labels
UL (Type I.C., Suitable for Damp Location), I.B.E.W.
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
Frame-In Kit
Reflector Trim
2
3
6
1
7
5
4
Overall Length
1004ICX: "
13" MIN.
24" MAX.
Overall Width
1004ICX:
10 3/8"
16 3/8"
12 1/4"
Height: 7 1/4"
Ceiling Opening: 5 1/2"
Top View
Ceiling Opening
AirSeal®is a registered trademark of Lightolier.
Romex®is a registered trademark of General Cable Industries Inc.
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight Recessed
Reflector Cone Satin Baffles Basic Adjustable Eyeball Enclosed Open Wall
Cone White Diffuser Wet Location Washer
1004ICX 1045 1012 1008 1005 1071 1027 1022 1021 1084CD 1035
1004ICXQ* 1046 1012NM 1008NM 1005WH 1027WH 1022WH 1024 1084WH 1035WH
1004ICXN 1046CD 1013 1010 1005NM 1027BK 1023 1090 1085
1004ICXNQ* 1013BK 1010NM 1005BNM 1027CD 1023WH 1095
1013WH 1076 1027NM 1082 1096
1013CD 1076WH 1027CDNM 1096CD
1013NM 1027BNM
1013BKNM 1027BKNM
1013CDNM 1038
1038NM
1048
1048NM *Supplied with integral push-In wire connectors
1004ICX
(Integral Screw)
1004ICXN
(Integral Nail)
