Linak ACTUATOR LA36 User manual

Page 1 of 92
© 2020 LINAK A/S
LINAK.COM/TECHLINE
Actuator LA36
User manual

Page 2 of 92
© 2020 LINAK A/S
Contents
Preface .............................................................................................................................................................................. 4
LINAK application policy..................................................................................................................................................... 5
Chapter 1
Safety instructions.............................................................................................................................................................. 6
Chapter 2
Mounting guidelines........................................................................................................................................................... 8
Mounting of cables .......................................................................................................................................................... 10
Electrical installation ........................................................................................................................................................ 11
Recommended fuse.......................................................................................................................................................... 11
Actuator without feedback ............................................................................................................................................... 12
Actuator with endstop signal output................................................................................................................................. 14
Actuator with relative positioning - Dual Hall.................................................................................................................... 16
Actuator with endstop signals and relative positioning - Dual Hall..................................................................................... 18
Actuator with relative positioning - Single Hall.................................................................................................................. 20
Actuator with endstop signals and relative positioning - Single Hall................................................................................... 22
Actuator with absolute positioning - Analogue feedback................................................................................................... 24
Actuator with endstop signals and absolute positioning - Analogue feedback.................................................................... 26
Actuator with absolute positioning - Mechanical potentiometer feedback......................................................................... 28
Actuator with endstop signals and absolute positioning - Mechanical potentiometer feedback........................................... 30
Actuator with absolute positioning - PWM........................................................................................................................ 32
Actuator with endstop signals and absolute positioning - PWM......................................................................................... 34
Actuator with IC Basic...................................................................................................................................................... 36
Actuator with IC Advanced - with Feedback and End Stop Signal....................................................................................... 38
IC options overview.......................................................................................................................................................... 41
Feedback configurations available for IC Basic, IC Advanced and Parallel ........................................................................... 42
Actuator configurations available for IC Basic, IC Advanced and Parallel ............................................................................ 44
Actuator with Parallel....................................................................................................................................................... 45
The parallel system........................................................................................................................................................... 47
BusLink software tool and the parallel system................................................................................................................... 48
System Monitoring for Parallel.......................................................................................................................................... 49
Alignment of the parallel actuator system ......................................................................................................................... 49
Parallel manual service mode............................................................................................................................................ 51
Actuator with CANbus (J1939) ......................................................................................................................................... 52
Actuator with CANopen: .................................................................................................................................................. 54
System combination possibilities for LA36 IC Advanced..................................................................................................... 56
TECHLINE signal cables .................................................................................................................................................... 56

Page 3 of 92
© 2020 LINAK A/S
Contents
Chapter 3
Troubleshooting ............................................................................................................................................................... 57
Troubleshooting for Parallel .............................................................................................................................................. 59
BusLink service counter - Reason for last stop................................................................................................................... 61
Chapter 4
Specifications .................................................................................................................................................................. 62
Usage: ............................................................................................................................................................................. 62
Actuator dimensions......................................................................................................................................................... 63
Built-in dimensions........................................................................................................................................................... 64
Manual Hand Crank......................................................................................................................................................... 65
Speed and current curves ................................................................................................................................................. 66
- 12V motor ..................................................................................................................................................................... 66
- 24V motor ..................................................................................................................................................................... 67
- 36V motor ..................................................................................................................................................................... 68
- 48V motor ..................................................................................................................................................................... 69
Label for LA36 ................................................................................................................................................................. 70
Key to symbols ................................................................................................................................................................. 71
LA36 Ordering example Econ ........................................................................................................................................... 72
Ordering example............................................................................................................................................................. 74
Chapter 5
Maintenance.................................................................................................................................................................... 75
Repair.............................................................................................................................................................................. 75
Main groups of disposal ................................................................................................................................................... 75
Warranty.......................................................................................................................................................................... 75
Declaration of conformity ................................................................................................................................................. 76
Declaration of Conformity................................................................................................................................................. 76
Declaration of incorporation of Partly completed machinery............................................................................................... 80
Chapter 6
IECEx/ATEX...................................................................................................................................................................... 81
Warnings ......................................................................................................................................................................... 81
General indication of risk:................................................................................................................................................. 82
Mounting and replacement of ATEX cables ....................................................................................................................... 82
Replacing an ATEX cable .................................................................................................................................................. 83
IECEx Certificates ............................................................................................................................................................. 85
ATEX Certificates.............................................................................................................................................................. 89
Adresses .......................................................................................................................................................................... 92

Page 4 of 92
© 2020 LINAK A/S
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls, and chargers.
This user manual does not address the end-user, but is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how
to install, use and maintain your LINAK electronics. It is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation. Before our products leave the factory they undergo full function and
quality testing. Should you nevertheless experience problems with your LINAK product/system, you are always welcome to contact your local dealer. LINAK subsidiaries
and some distributors situated all over the world have authorised service centres, which are always ready to help you.
LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance with the specifications, maintenance being done correctly
and any repairs being carried out at a service centre, which is authorised to repair LINAK products.
Changes in installation and use of LINAK products/systems can affect their operation and durability. The products are not to be opened by unauthorised personnel.
The User Manual has been written based on our present technical knowledge.We are constantly working on updating the information and we therefore reserve the right
to carry out technical modifications.
LINAK A/S

Page 5 of 92
© 2020 LINAK A/S
LINAK application policy
The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware, software, technical
advice, etc. related to an existing or a new customer application.
LINAK products as defined above are applicable for a wide range of applications within Medical, Furniture, Desk, and Industry areas.Yet, LINAK cannot know
all the conditions under which LINAK products will be installed, used, and operated, as each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application, vibration, load, humidity, temperature,
frequency, etc.) can only be verified by testing, and shall ultimately be the responsibility of the LINAK customer using any LINAK product.
LINAK shall be responsible solely that LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer
to ensure that the specific LINAK product can be used for the application in question.

Page 6 of 92
© 2020 LINAK A/S
Please read this safety information carefully:
Be aware of the following three symbols throughout the user manual:
Warning!
Failing to follow these instructions can cause accidents resulting in serious personal injury.
Recommendations
Failing to follow these instructions can result in the actuator suffering damage or being ruined.
Additional information
Usage tips or additional information that is important in connection with the use of the actuator.
Furthermore, ensure that all staff who are to connect, mount, or use the actuator are in possession of the necessary information and that they have access
to this user manual.
Persons who do not have the necessary experience or knowledge of the product/products must not use the product/products. Besides, persons with reduced
physical or mental abilities must not use the product/products, unless they are under surveillance or they have been thoroughly instructed in the use of the
apparatus by a person who is responsible for the safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play with the product.
Before you start mounting/dismounting, ensure that the following points are observed:
• The actuator is not in operation.
• The actuator is free from loads that could be released during this work.
Before you put the actuator into operation, check the following:
• The actuator is correctly mounted as indicated in the relevant user instructions.
• The equipment can be freely moved over the actuator’s whole working area.
• The actuator is connected to a mains electricity supply/transformer with the correct voltage and which is dimensioned and adapted to the actuator in
question.
• Ensure that the voltage applied matches to the voltage specified on the actuator label.
• Ensure that the connection bolts can withstand the wear.
• Ensure that the connection bolts are secured safely.
Chapter 1
Safety instructions

Page 7 of 92
© 2020 LINAK A/S
During operation, please be aware of the following:
• Listen for unusual sounds and watch out for uneven running. Stop the actuator immediately if anything unusual is observed.
• Do not sideload the actuator.
• Only use the actuator within the specified working limits.
• Do not step or kick on the actuator.
When the equipment is not in use:
• Switch off the mains supply in order to prevent unintentional operation.
• Check regularly for extraordinary wear.
Classification
The equipment is not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide.
• Do not sideload the actuator.
• When mounting the LA36 in the application ensure that the bolts can withstand the wear and that they are secured safely.
• If irregularities are observed, the actuator must be replaced.
Recommendations
• Do not place load on the actuator housing and do prevent impact or blows, or any other form of stress to the housing.
• Ensure that the cable cover is mounted correctly. Use 3.5 Nm torque.
• Ensure that the duty cycle and the usage temperatures for LA36 actuators are respected.
• Ensure that the cable cannot be squeezed, pulled or subjected to any other stress.
• Furthermore, it will be good practice to ensure that the actuator is fully retracted in the “normal” position. The reason is that there will be a vacuum
inside the actuator if it is extended which over time can lead to water entering the actuator.
• If the actuator (without integrated controller) is mounted in an application where a mechanical stop prevents the endstop switches in the actuator from
being activated, the actuator must be equipped with an electrical safety device (current monitoring) or external limit switch.
Warnings

Page 8 of 92
© 2020 LINAK A/S
Mounting guidelines
LINAK®linear actuators are quickly and easily mounted by slipping pins through the holes on each end of the units and into brackets on the machine
frame and the load.
The mounting pins must be parallel to each other as shown in Figure 1. Pins, which are not parallel to each other, may cause the actuator to bend and be
damaged.
The load should act along the stroke axis of the actuator since off centre loads may cause bending and lead to premature failure. See Figure 2.
Make sure the mounting pins are supported in both ends. Failure to do so could shorten the life of the actuator. Also, avoid applying a skew load on the
actuator.
The actuator can rotate around the pivot point in the front and rear end. If this is the case it is of high importance that the actuator is able to move freely
over the full stroke length, both during the development and during daily operation. Please pay special attention to the area around the housing where
parts can be trapped and cause damages to the application and actuator.
In applications with high dynamic forces LINAK recommends not to use the fully extended or retracted position over longer time, as this can damage the
endstop system permanently.
E
F
789
A
B
C
D
1 2 3 4 5 6
E
A
B
C
D
Right Wrong Wrong Wrong
X
X
Figure 1
Figure 2
Chapter 2
Please be aware that if the LA36 is used for solar applications the actuator must be mounted with the motor housing turned upwards and the
wires pointing downwards.

Page 9 of 92
© 2020 LINAK A/S
Mounting guidelines
030618/DS
Instruktion vedr. uddrejning af inderrør – LA27 + LA27C
Til salesbackup, brugsanvisning og datablad.
Ved montage og ibrugtagning, er det ikke tilladt at dreje unødvendigt mange gange på
stempelstangsrøret. Hvis øjet ikke er positioneret korrekt, er det tilladt først at skrue
røret i bund (1), og derefter skrue det maksimalt ½ omgang ud igen (2).
• The mounting pins must have the correct dimension.
• The bolts and nuts must be made of a high quality steel grade (e.g. 10.8).
No thread on the bolt inside the back fixture or the piston rod eye.
• Bolts and nuts must be protected so there is no risk for them to fall out.
• Do not use a torque that is too high when mounting the bolts for the back fixture or the piston rod eye.
This will stress the fixtures.
Please note:
The piston rod eye is only allowed to turn 0-90 degrees.
Instruction concerning the turning of the piston rod eye and inner tube:
• When mounting and taking into use, it is not permitted to make excessive turns of the piston rod eye. In cases where the eye is not
positioned correctly, it is permitted to first screw the eye down to its bottom position, at a maximum torque of 2Nm (1), and thereafter a
maximum 90 degrees turn outwards again (2).
• As the piston rod eye can turn freely, it is important to ensure that the eye cannot rotate if the actuator is used in a pull application. If this
happens, the actuator will be pulled apart and destroyed.
Warning!
If the actuator is used for pull in an application where personal injury can occur, the following is valid:
It is the application manufacturer’s responsibility to incorporate a suitable safety arrangement,which will prevent personal injury from occurring,
if the actuator should fail.
Warning!
LINAK’s actuators are not designed for use within the following fields:
• Offshore installations • Nuclear power generation
• Aeroplanes and other aircraft

Page 10 of 92
© 2020 LINAK A/S
Mounting of cables
When changing the cables on a LINAK actuator, it is important that this is done carefully, in order to protect the plugs and pins. Before the new
cable is mounted, we recommend that the socket is greased with vaseline, to keep the high IP protection and ensure an easy mounting. Please
be sure that the plug is in the right location and fully pressed in before the cable lid is mounted.
Please note that if the cables are mounted and dismounted more than 3 times the plugs can be damaged. Therefore, we recommend that such
cables are discarded and replaced.
Also note that the cables should not be used for carrying the actuator.
We recommend to take some precaution and design the wire connection in a way, where the cable end is kept inside a closed, protected area
to guarantee the high IP protection.
NOT VALID FOR ATEX CABLES, PLEASE REFERE TO CHAPTER 6
3. Slide the cover onto
the actuator.
The torque of the
cover screw is
approx. 3.5 ± 0.3 Nm
TORX 25IP
1. Unscrew the cover and
remove the two blind
plugs.
2. Plug in the power
cable and/or the
signal cable.

Page 11 of 92
© 2020 LINAK A/S
Electrical installation
• To ensure maximum self-locking ability, please be sure that the motor is shorted when stopped. Actuators with integrated controller
provide this feature, as long as the actuator is powered.
• When using soft stop on a DC-motor, a short peak of higher voltage will be sent back towards the power supply. It is important when
selecting the power supply that it does not turn off the output, when this backwards load dump occurs.
The power supply for actuators without integrated controller must be monitored externally and cut off in case of current overload.
for actuators without integrated controller
Type Spindle
Pitch (mm)
Thrust max.
Push/Pull
(N)
Typical Amp. at full load
(A)
48 V 36 V 24 V 12 V
Recommended fuse
48 V 36 V 24 V 12 V
36120xxxxxxAxxxxF... 12 2600 -- - 21.0 -- - 40.0
36120xxxxxxAxxxxG... 12 4500 - - - 20.7 - - - 40.0
36120xxxxxxAxxxxH... 12 6800 --- 21.0 - - - 40.0
36200xxxxxxAxxxxF... 20 1700 - - - 22.0 - - - 40.0
36200xxxxxxAxxxxE... 20 500 --- 20.0 - - - 40.0
36120xxxxxxBxxxxF... 12 2600 --10.4 - - - 20.0 -
36120xxxxxxBxxxxG... 12 4500 --10.2 - - - 20.0 -
36120xxxxxxBxxxxH... 12 6800 --10.3 - - - 20.0 -
36200xxxxxxBxxxxF... 20 1700 --10.3 - - - 20.0 -
36200xxxxxxBxxxxE... 20 500 --10.0 - - - 20.0 -
36120xxxxxxCxxxxF... 12 2600 -8.0 - - - 16.0 - -
36120xxxxxxCxxxxG... 12 4500 -8.0 - - - 16.0 - -
36120xxxxxxCxxxxH... 12 6800 -8.0 - - - 16.0 - -
36200xxxxxxCxxxxF... 20 1700 -8.0 - - - 16.0 - -
36200xxxxxxCxxxxE... 20 500 -8.0 - - - 16.0 - -
36120xxxxxxDxxxxF... 12 2600 7 - - - 10.0 - - -
36120xxxxxxDxxxxG... 12 4500 7 - - - 10.0 - - -
36120xxxxxxDxxxxH... 12 6800 7 - - - 10.0 - - -
36200xxxxxxDxxxxF... 20 1700 7 - - - 10.0 - - -
36200xxxxxxDxxxxE... 20 500 7 - - - 10.0 - - -
Recommended
fuse

Page 12 of 92
© 2020 LINAK A/S
4
2020 © LINAK A/S
Without feedback
BROWN
BLUE
36XXXXXXX000XX-XXXXXXXXXXXXXXX
36XXXX+10XXXXXX
37XXXX+10XXXXXX
Compliant with:
Powered by Danfoss
2
1
2
1
Connection diagram:
Actuator without feedback

Page 13 of 92
© 2020 LINAK A/S
Actuator without feedback
I/O specifications:
4
2020 © LINAK A/S
Without feedback
Input/Output Specification Comments
Description Permanent magnetic DC motor.
Brown 12, 24, 36* or 48* VDC (+/-)
*Only available on LA36
12 V ± 20%
24 V ±10%
36 V ±10%
48 V ± 10%
Under normal conditions:
12 V, max. 26 A depending on load
24V , max. 13 A depending on load
36 V, max. 10 A depending on load
48 V, max. 7 A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Not to be connected
Black Not to be connected
Green Not to be connected
Yellow Not to be connected
Violet Not to be connected
White Not to be connected

Page 14 of 92
© 2020 LINAK A/S
Actuator with endstop signal output
Connection diagram:
5
2020 © LINAK A/S
Endstop signal output
36XXXXXXX000XX-XXXXXXXXXXXXXXX
36XXXX+20XXXXXX
37XXXX+20XXXXXX
Compliant with:
Powered by Danfoss
*YELLOW/GREEN: Endstop signals out are NOT potential free!
If you wish to use the endstop signals, you will have to keep power on the brown,
blue, red and black wires, otherwise the signal will be lost.
YELLOW
GREEN
BROWN
BLUE
RED
BLACK
+
-
2
1
2
5
6
1
AMP DEUTSCH
6P6P
2
1
2
5
6
1
*YELLOW/GREEN: End Stop Signals out are NOT potential free
TIP: If you wish to use the End Stop Signals, you will have to keep power on the red and black wires, otherwise the signal will be lost.

Page 15 of 92
© 2020 LINAK A/S
Actuator with endstop signal output
I/O specifications:
5
2020 © LINAK A/S
Endstop signal output
Input/Output Specification Comments
Description The actuator can be equipped with
electronically controlled endstop signals out.
See connection diagram, figure above
Brown 12, 24, 36* or 48* VDC (+/-)
*Only available on LA36
12 V ± 20%
24 V ± 10%
36 V ± 10%
48 V ± 10%
Under normal conditions:
12 V, max. 26 A depending on load
24V , max. 13 A depending on load
36 V, max. 10 A depending on load
48 V, max. 7 A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12 - 48 VDC Current consumption:
Max. 40 mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Endstop signal out Output voltage min. VIN - 2 V
Source current max. 100 mA
NOT potential free
Yellow Endstop signal in
Violet Not to be connected
White Not to be connected
Tip: If you wish to use the endstop signals, you will have to keep power on the brown,
blue, red and black wires, otherwise the signal will be lost.

Page 16 of 92
© 2020 LINAK A/S
Actuator with relative positioning - Dual Hall
Connection diagram:
6
2020 © LINAK A/S
Relative positioning - Dual hall
36XXXXXXXH00XX-XXXXXXXXXXXXXXXX
36XXXX+0H/1HXXXXXX
37XXXX+1HXXXXXX
Diagram of Dual hall:
Compliant with:
Powered by Danfoss
YELLOW
GREEN
BROWN
BLUE
RED
BLACK
+
-
2
1
2
1
2
5
6
1
2
5
6
1
AMP DEUTSCH
6P6P

Page 17 of 92
© 2020 LINAK A/S
Actuator with relative positioning - Dual Hall
I/O specifications:
6
2020 © LINAK A/S
Relative positioning - Dual hall
Input/
Output Specification Comments
Description The actuator can be equipped with Dual Hall that gives a relative
positioning feedback signal when the actuator moves.
See connection diagram, figure above
Brown 12, 24, 36* or 48* VDC (+/-)
*Only available on LA36
12 V ± 20%
24 V ± 10%
36 V ± 10%
48 V ± 10%
Under normal conditions:
12 V, max. 26 A depending on load
24V , max. 13 A depending on load
36 V, max. 10 A depending on load
48 V, max. 7 A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12 - 48 VDC Current consumption:
Max. 40 mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Hall B Hall output (PNP)
Movement per each Hall pulse:
The Hall sensor signals are generated
by the turning of the actuator gearing.
These signals can be fed into a PLC
(Programmable Logic Controller). In
the PLC the quadrature signals can be
used to register the direction and
position of the piston rod.
Output voltage min. VIN - 2 V
Current output 12 mA
Overvoltage on the motor can result in
shorter pulses.
N.B. For more precise measurements,
please contact LINAK A/S.
Actuator Gear: Pitch: mm/count
LA36 H12 mm 0,662
LA36 H16 mm 0,883
LA36 G16 mm 1,016
LA36 F16 mm 2,309
Yellow Hall A LA36 F20 mm 2,890
LA37 C2,5 mm 0,138
LA37 C8 mm 0,442
The frequency is 14-26 Hz on Single Hall output
depending on load.
Overvoltage on the motor can result in shorter
pulses.
Violet Not to be connected
White Not to be connected

Page 18 of 92
© 2020 LINAK A/S
Actuator with endstop signals and relative positioning - Dual Hall
Connection diagram:
*VIOLET/WHITE:
Endstop signals out are NOT potential free!
If you wish to use the endstop signals, you will have to keep power on the brown, blue, red and black wires, otherwise the signal will be lost.
7
2020 © LINAK A/S
Endstop signals and relative positioning - Dual hall
Diagram of Dual hall:
36XXXXXXXH00XX-XXXXXXXXXXXXXXXX
36XXXX+2HXXXXXX
37XXXX+2HXXXXXX
*VIOLET/WHITE: Endstop signals out are NOT potential free
Tip: If you wish to use the endstop signals, you will have to keep power on the brown, blue,
red and black wires, otherwise the signal will be lost.
Compliant with:
Powered by Danfoss
BROWN
BLUE
VIOLET*
WHITE*
RED
YELLOW
BLACK
+
-
GREEN
2
1
2
5
6
1
2
5
6
1
2
1
4
3
4
3
AMP DEUTSCH
6P6P
*VIOLET/WHITE: End Stop Signals out are NOT potential free
TIP: If you wish to use the End Stop Signals, you will have to keep power on the red and black wires, otherwise the
signal will be lost.

Page 19 of 92
© 2020 LINAK A/S
Actuator with endstop signals and relative positioning - Dual Hall
I/O specifications:
7
2020 © LINAK A/S
Endstop signals and relative positioning - Dual hall
Input/
Output Specification Comments
Description The actuator can be equipped with Dual Hall that gives a relative
positioning feedback signal when the actuator moves.
See connection diagram, figure above
Brown 12, 24, 36* or 48* VDC (+/-)
*Only available on LA36
12 V ± 20%
24 V ± 10%
36 V ± 10%
48 V ± 10%
Under normal conditions:
12 V, max. 26 A depending on load
24V , max. 13 A depending on load
36 V, max. 10 A depending on load
48 V, max. 7 A depending on load
To extend actuator:
Connect Brown to positive
To retract actuator:
Connect Brown to negative
Blue
To extend actuator:
Connect Blue to negative
To retract actuator:
Connect Blue to positive
Red Signal power supply (+) 12 - 48 VDC Current consumption:
Max. 40 mA, also when the
actuator is not running
Black Signal power supply GND (-)
Green Hall B Hall output (PNP)
Movement per each Hall pulse
The Hall sensor signals are generated
by the turning of the actuator gearing.
These signals can be fed into a PLC
(Programmable Logic Controller). In
the PLC the quadrature signals can be
used to register the direction and
position of the piston rod.
Output voltage min. VIN - 2 V
Current output 12 mA
Overvoltage on the motor can result in
shorter pulses.
N.B. For more precise measurements,
please contact LINAK A/S.
Actuator G:ear Pitch: mm/count
Yellow Hall A LA36 H12 mm 0,662
LA36 H16 mm 0,883
LA36 G16 mm 1,016
LA36 F16 mm 2,309
LA36 F20 mm 2,890
LA37 C2,5 mm 0,138
LA37 C8 mm 0,442
The frequency is 14-26 Hz on Single Hall
output depending on load.
Overvoltage on the motor can result in shorter
pulses.
Violet Endstop signal in Output voltage min. VIN - 2 V
Source current max. 30 mA
NOT potential free
White Endstop signal out

Page 20 of 92
© 2020 LINAK A/S
Actuator with relative positioning - Single Hall
Connection diagram:
8
2020 © LINAK A/S
Relative positioning - Single hall
36XXXXXXXK00XX-XXXXXXXXXXXXXXXXXX
36XXXX+1KXXXXXX
37XXXX+1KXXXXXX
Compliant with:
Powered by
Danfoss
VIOLET
BROWN
BLUE
RED
BLACK
+
-
2
1
AMP DEUTSCH
6P6P
2
1
1
2
1
2
1
1