Lincoln C Series Owner's manual

Page
Section - E35
- 43B
Form 422680June 2002
MODEL 84673
BARE REEL
SERIES C
OWNER/OPERATOR MANUAL
SPECI FICATIONS
Maximum working pressure 2000 p.s.i.
Material Inlet 3/4 NPT (Female
Material outlet 3/4 NPT (Female
Sheave width 10
Sheave diameter 19-1/4
Drum diameter 12-3/4
Overall width 15-1/2
Overall height 22-1/2
Overall depth 21
Maximum hose capacities (Including hang down :
5/8 or 3/4 I.D. Hose 75 Ft.
NOTE: Maximum hose capacities are based on SAE specified
hoses. Exceeding these capacities voids warranty. Refer to
DELIVERY HOSE INSTALLATION for proper hose to reel
assembly.
DESCRIPTION
Model 84673 unit is a heavy duty lubreel designed for
bus and truck lubrication or wherever extra heavy duty
construction and longer length delivery hose is required.
The reel can be installed as a single unit or in multiple
configurations.
Reel features include a reel latch that automatically
locks at desired positions as the hose is extended and
releases with a short pull on the hose.
OWNER/OPERATOR RESPONSIBILITY
It is the owner/operator responsibility to properly use and
maintain this equipment.
The instructions and warnings contained in this manual
shall be read and understood by the owner/operator prior
to operating this equipment.
If an owner/operator does not understand English, the
contents of this manual shall be explained in the owner/
operator native language to assure the owner/operator
comprehends.
It is the owner/operator responsibility to maintain the
legibility of all warning and instruction labels.
The owner/operator shall retain this manual for
future reference to important warnings, operating
and maintenance instructions
One Lincoln Way
St. Louis, MO 63120-1578
Customer Ser ice +1.314.679.4200
Fax [phone]

Page Number - 2 Form 422680
 Do not exceed the stated maximum working pressure of the reel or of the lowest rated component in your system.
 Do not alter or modify any part of this equipment.
 Do not operate this equipment with combustible gas.
 Do not attempt to repair or disassemble the equipment while the system is pressurized.
 Make sure all fluid connections are securely tightened before using this equipment.
 Always read and follow the fluid manufacturers recommendations regarding fluid compatibility, and the use of protecti e
clothing and equipment.
 Check all equipment regularly and repair or replace worn or damaged parts immediately.
 Ne er point the dispensing al e at any part of the body or at another person.
 Ne er try to stop or deflect material from dispensing al e or leading connection or component with your hand or body.
 Always check equipment for proper operation before each use, making sure safety de ices are in place and operating
properly.
 Always follow the pressure relief procedure after shutting off the pump, when chocking or ser icing any part of the
system, and when installing, cleaning or changing any part of the system.
FAILURE TO HEED THE FOLLOWING WARNINGS INCLUDING MISUSE, OVER PRESSURIZING, MODIFYING PARTS,
USING INCOMPATIBLE CHEMICALS AND FLUIDS, OR USING WORN OR DAMAGED PARTS, MAY RESULT IN
EQUIPMENT DAMAGE AND/OR SERIOUS PERSONAL INJURY, FIRE, EXPLOSION, OR PROPERTY DAMAGE.
ASSEMBLY
Assemble reel as follows. Refer to SERVICE PARTS for part
numbers and location.
A. Assemble arbor and ratchet casting (237769) to support
assembly (237656) with hex head screws (50014) and
secure with hex nuts (51022).
B. Lubricate V-ring seal (237671) and assemble onto arbor
and ratchet casting (237769) with lip facing away from
arbor ratchet.
C. Assemble power spring assembly (248494) onto arbor
and ratchet casting (248494) until spring canister
bottoms on arbors shoulder.
D. Lubricate V-ring seal (237673) and assemble onto arbor
and ratchet casting (237769) with lip facing toward
spring canister.
E. Assemble axle assembly (242000) to shea e assembly
(237771) and secure with standoffs (237780).
F. Assemble axle and shea e assembly to reel by sliding
the axle assembly (242000) through the bearings in the
arbor and ratchet casting (237769) and securing with
washer (48217) and Tru-arc (68424).
Not : Shim as required using shims (48385) between
washer (48217) and arbor and ratchet casting (237769)
to eliminate axle end play.
G. Assemble outboard axle assembly (237781) to standoffs
(237780) and secure with nuts (51010).
H. Rotate shea e assembly (237771) and align mounting
holes with mating holes in power spring canister
(248494) and secure using carriage bolts (237738),
carriage bolt (237739) and nuts (51010). Note: The
carriage bolt (237739) (.875 long) must be assembled in
hole adjacent to pawl pin on power spring assembly.
I. Assemble rollers onto 5/16 diameter pins in the order
illustrated on page (6). Hold in place while inserting the
four 5/16 washer head bolts through the assembly and
secure with four 5/16 washer head nuts. Assemble
roller outlet arm assembly onto three of the bolts
(50014) and secure using three nuts (51022).
J. Assemble swi el assembly(84679) in axle assembly
(242000) and tighten.
K. Assemble swi el outlet adapter (242015) into the axle
assembly (242000) and secure.
L. Assemble hose clamp (237760) to shea e assembly
(237771) with carriage bolt (237738) and secure with nut
(51010).
M. Assemble pawl (237683) to pawl pin on spring canister
(248494) and secure with washer (48327) and Tru-arc
(66316).

Page Number - 3
Form 422680
N. Assemble pawl spring (237695) to pawl (237683) and
carriage bolt (237739) and secure with locknut (51304).
0. Install Beraing (242725) into Outboard Bearing Assembly
(237784) and secure with Bearing Retainer (272169).
Attach completed Assembly to the Outboard Support
(237787) using screws (50016). HAND TIGHTEN ONLY
AT THIS POINT.
P. Assemble outside bearing assembly and support to reel
assembly by sliding outboard axle through bearing. Align
two .406 mounting holes in both base and support and
insert one roll pin in each hole.
Q. Adjust/align outside bearing assembly for free drum.
INSTALLATION
DELIVERY HOSE
DELIVERY HOSE INSTALLATION (MAXIMUM
SPRING TENSION)
For smoother operation during retraction and to increase
hose life, detaic hose by wiping entire hose length with a
light lubricating oil before installing on reel.
Assemble outlet adapter to hose and tighten securely. Use
teflon tape on threads to pre ent leaks.
To pre ent damaging hose connections and/or
components when pulling hose from reel, pull on the
hose itself and not on the control al e or swi el. Do not
pull or jerk on the hose when fully withdrawn from the
reel.
See Figure (1). Insert hose end with outlet adapter
through roller outlet and secure to axle head with U-
keeper. Make sure seal is installed correctly in axle
before assembling.
From open side of reel (with outside support remo ed), loop
entire length of hose onto reel in a clockwise direction. Pull
hose out through roller outlet to wind power spring. When
hose is completely extended, latch reel to pre ent it from un-
winding.
Continue to add loops of hose and pull out
hose until power spring winds tight.
IMPORTANT
INSTRUCTIONS
Perform the following instructions as stated to
correctly set the power spring for maximum tension.
Allow reel to retract two full revolutions and latch
reel Carefully unloop remaining hose from reel.

Page Number - 4 Form 422680
To a oid damaging reel components,
always make sure hose clamp is
properly installed.
Position hose clamp so that approxi-
mately 1/2 loop of hose remains on
reel and latching does not occur when
hose is fully extended.
Slide ball stop o er free end of hose
and position slightly below roller outlet.
Tighten screws to secure ball stop to
hose.
Pow r spring is now s t to maximum
t nsion.
ADJUSTING SPRING
TENSION
To pre ent premature power spring
failure, spring tension should be
adjusted so that it requires at least
two full turns of the reel shea e
before the spring is wound tight.
Should less spring tension be desired,
pull hose out from roller outlet to
pro ide slack and latch reel.
Unwind one loop of hose from reel.
Pull excess hose out through roller
outlet and unlatch reel to retract hose.
Check tension and repeat abo e
procedure until desired tension is
obtained.
Reattach/assemble outboard support to
reel. (See Page 3, Steps 0 thru 0).
ATTACHING CONNECTING
HOSES
To pre ent damage to connecting
hose when installing hose to reel,
sufficient clearance must be pro ided
from outside edge of shea e.
See Figure (2). Reconnect inlet
adapter to swi el body and replace U-
keeper.
Connect other end of connecting hose
to material supply line source or
connection.

Page Number - 5
Form 422680
DISASSEMBLY
To disassemble, perform ASSEMBLY procedures in re erse.
REPAIR
Repair is limited to replacement of listed ser ice parts.
Special procedures and tools are required. Contact Lincoln-
Customer Ser ice, One Lincoln Way, St. Louis, MO 63120-
1578, [phone] for your nearest authorized ser ice
center.
When ordering replacement parts, list: part number, de-
scription, model number and series number.
LIMITED WARRANTY
Lincoln warrants that lubrication equipment, materials
dispensing equipment and other related equipment manu-
factured by it will be free from defects in material and
workmanship during the one (1) year following the date of
purchase. If equipment pro es to be defecti e during this
warranty period, it will be repaired or replaced without
charge, pro ided that factory examination indicat s th
quipm nt to b d f ctiv . To obtain r pair or r plac -
m nt, it must b shipp d, transportation charg s pr paid,
with proof of dat of purchas to a Lincoln authoriz d
Warranty and S rvic C nt r, within th on (1) y ar
following th dat of purchas .
This warranty is extended to the original retail purchaser
only. This warranty does not apply to equipment damaged
from accident, o erload, abuse, misuse, negligence, faulty
installation or abrasi e or corrosi e materials, or to equip-
ment repaired or altered by anyone not authorized by Lincoln
to repair or alter the equipment. This warranty applies only
to equipment installed and operated according to the
recommendations of Lincoln or its authorized field person-
nel.
No other express warranty applies to lubrication equipment,
materials dispensing equipment, and other related
equipment manufactured by Lincoln. ANY IMPLIED WAR-
RANTIES applicable to lubrication equipment, materials
dispensing equipment, and other related equipment
manufactured by Lincoln INCLUDING THE WARRANTIES
OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM
THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU.
In no e ent shall Lincoln be liable for incidental or conse-
quential damages. The liability of Lincoln on any claim for
loss or damage arising out of the sale, resale, or use of
lubrication equipment, materials dispensing equipment,
and other related equipment shall in no e ent exceed the
purchase price. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLYTO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
REEL INSTALLATION AND
ADJUSTMENT
See Figure (3). The guide arm may be positioned in 22-1/2
degree increments. For ease of operation and increased
hose life, the guide arm should be positioned to minimize
hose strain as the deli ery hose is pulled through the roller
outlet.
Three studs must be used to securely attach the guide arm, It
may be necessary to change the position of the hex head
screw and one stud in order to obtain the desired guide arm
position.
The hose clamp must be relocated if the guide arm is reposi-
tioned.
SAFETY INFORMATION
Read and understand all warnings, cautions and instruc-
tions before operating this equipment. Extreme caution
should be used when operating this equipment as personal
injury and/or property damage can result from equipment
misuse. Adequate personal protection is recommended to
pre ent splashing of material on the skin or in the eyes.
ALWAYS disconnect air coupler from pump when the pump
is not being used.
PRESSURE RELIEF PROCEDURE
Always perform this procedure when the pump is shut off
and before checking, ser icing, installing, cleaning or repair-
ing any part of this system.
Perform the following procedure:
A. Disconnect the air supply to the pump.
B. Point the dispensing al e away from yourself and
others.
C. Open the dispensing al e into an appropriate container
until the pressure is relie ed.
If the abo e procedure does not relie e the pressure, the
dispensing al e or hose may be restricted
To relie e the pressure, ery slowly loosen the hose end
coupling. Then loosen completely and clear the dispensing
al e and/or hose.
INSPECTION
Prior to operation or maintenance a isual inspection shall
be made. Check reelsystem for leaks, worn or missing
parts.
Any reel that appears to be damaged in any way, is badly
worn or operates abnormally shall be remo ed from use
until repairs are made. Contact factory authorized ser ice
center for repairs.
If o erpressurizing of the equipment is belie ed to ha e
occurred, contact a factory authorized ser ice center for
inspection of the reel.
Annual inspection by a factory authorized ser ice center is
recommended.

Page Number - 6 Form 422680
565223 565253
272162
237738
(5 Reqd)
242022
(8X) ø .046 Mounting Hole
10.000
272161
(2 Reqd) 272163
(4 Reqd)
237673
3/4 PTF Outlet
242015
242000
50016 (4 Reqd)
237784
272169
242725
242738
237781
51010 (3 Reqd)
(Torque to
7-8 Ft. Lbs.) 237780
(3 Reqd)
51010
(Torque to
7-8 Ft. Lbs.)
237738
272382
237771
237787
272160
(2 Reqd)
272040
(22 Reqd)
248494
237671
48385 (4 Reqd)
(Shim as Reqd)
48217
3/4 PTF Inlet
84679
68424
50014 (4 Reqd)
51022 (7 Reqd)
237769
13162
237683
66316
48327
237695
51304
237739
51010 (6 Reqd)
237656

Page Number - 7
Form 422680
68340
565256
565262
PART QTY DESCRIPTION PART QTY DESCRIPTION
13162 1 Pin .405 x1-1/8 237780 3 Standoff
48217 1 Gland Pkg Washer 237781 1 Axle,Outboard Weld
48327 1 Washer, Pkg. .915 OD 237784 1 Outboard Bearing Assembly
48385 4 Washer,Shim 1-3/8 237787 1 Support, Outboard
50014 4 SCR HHCS 5/16-18 x1-3/4 242000 1 Axle,High Flow
50016 4 Screws 242015 1 Adapter,Swivel
50757 4 SCR HHCS 1/4-20 x5/8 242022 1 Label,Nameplate
51010 10 Nut,Hex1/4-20 GR5 242505 1 Nipple, Formed
51022 7 Jam Nut 242506 1 Elbow,3/4 FPTx45
51304 1 Lock Nut 242725 1 Bearing, Special
66316 1 Ring,Retaining 242738 1 Cap,Vinyl 1.5 ID BL
68340 1 Decal,Instr 248494 1 Spring, PowerAssembly
68424 1 Ring,Retaining EXTTRU 272040 22 Roller
84679 1 Swivel Assembly 272160 2 Pin
237656 1 SupportWeld’t 272161 2 Pin
237671 1 Pkg,V-Ring 2.68 OD 272162 1 Arm Roller SupportAssy
237673 1 Pkg,V-Ring 1.82 OD 272163 4 Retainer, Shaft
237683 1 Pawl,Latch 272169 1 Retaining Ring
237695 1 Spring,Extension 272382 1 Clamp,Hose (for 3/4" ID Hose
)
237738 6 Bolt,Carriage 1/4-20 x1/2 GR5 565223 1 Label,Logo Lincoln
237739 1 Bolt,Carriage 1/4-20 x1 GR5 565253 1 Label,Caution
237769 1 Arbor and ratchet casting 565256 2 Label,Capacity
237771 1 Sheave 565262 1 Label,Caution
SERVICE PARTS (CONT)
50757
(4 Reqd)
242505
242506
3/4 PTF (REF)
16684
70518
70517
(2 Reqd)
48652
70519
16685
70515
(2 Reqd)
48653
70516
31116

Page Number - 8 Form 422680