Lincoln SKF A Series Product manual

Installation and maintenance guide
1262E, series “A”, base model 1260, original instruction
PowerLuber grease gun
(lithium ion)
Date of issue February 2023
Form number 425014
Version 2

*Indicates change.
Contents
Declaration of Conformity* . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
U.K. Declaration of Conformity* . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Explanation of signal words for safety . . . . . . . . . . . . . . . . . . . 5
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General power tool safety warnings. . . . . . . . . . . . . . . . . . . . . 6
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Work area safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Personal safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power tool use and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Battery tool use and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety of others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specific safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Residual risks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Labels on tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Protecting the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety instructions for battery and charger . . . . . . . . . . . . . . 9
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tool use and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1260 series PowerLuber grease gun . . . . . . . . . . . . . . . . . . . . . . 12
Replace grease cartridge or refill tube . . . . . . . . . . . . . . . . . . . . . 13
Priming instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Install grease cartridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fill gun from bulk container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Fill gun with filler pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Expel air pockets (air purging) . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Charger operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Charging battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Charging procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Important charging notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Exploded view and parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2

I, the undersigned of Lincoln Industrial Corporation, do hereby declare that the equipment specified above, in its intended use, conforms to
the requirements of the above directives and harmonized standards at the time of placing the above product on the market.
___________________________________
Robert Collins
Technical Compliance Manager
St. Louis, MO, U.S.A.
2022/11/03 *Indicates change.
This Declaration of Conformity is issued
under sole responsibility of the
manufacturer. Lincoln Industrial Corporation
hereby declares that the machinery stated
below:
Name: PowerLuber)
Description: Grease gun (lithium-ion)
Model number(s):
1262E (base model 1260)
Name: PowerLuber battery:
Description: Lithium-ion battery (12 V)
Part number: 1861
Name: PowerLuber battery charger
Description:
220-240 V Charger input (EU)
Part number: 1870E
Year of CE: 2018
in its intended use, is in conformity with the
relevant union harmonization legislation:
• Low Voltage Directive (LVD) 2014/35/EU
• Electromagnetic Compatibility (EMC)
2014/30/EU
• Battery, according to Directive
2006/66/EC
• Machinery Directive 2006/42/EC
• Hazardous Substances (RoHS2)
2011/65/EU and (RoHS3) 2015/863
and conforms to the following harmonized
standards:
• EN 55014-1:2021
• EN 55014-2:2021
• IEC 60745-1:2009+A11:2010
• EN IEC 63000:2018
• EN 60335-2-29:2004+A2:2010
• EN 60335-1:2012
• EN 62233-1:2008
Declaration of Conformity* DOCUMENT NUMBER
425014.DoC
Manufacturer name/address:
Lincoln Industrial Corporation
5148 N. Hanley Road
St. Louis, MO 63134 U.S.A.
TEL: [phone] FAX: [phone]
Authorized to compile the technical file:
SKF Lubrication Systems Germany GmbH
Heinrich-Hertz-Straße 2-8
69190 Walldorf, Germany
EMAIL: [e-mail] WEBSITE: www.skf.com
And conforms to RoHS, states that homoge-
neous material levels are less than or equal
to 0.1% by weight:
The manufacturer maintains a technical file
containing summary, test reports and prod-
uct documentation:
Technical file summary sheet number:
RA425014
3

This U.K. Declaration of Conformity is issued
under sole responsibility of the
manufacturer. Lincoln Industrial Corporation
hereby declares that the machinery stated
below:
Name: PowerLuber)
Description: Grease gun (lithium-ion)
Model number(s):
1262E (base model 1260)
Name: PowerLuber battery:
Description: Lithium-ion battery (12 V)
Part number: 1861
Name: PowerLuber battery charger
Description:
220-240 V Charger input (EU)
Part number: 1870E
Year of CE: 2018
in its intended use, is in conformity with the
relevant union harmonization legislation:
• Supply of Machinery (Safety) Regulations
2008 (S.I. 2008:1597)
• Electrical Equipment (Safety) Regulations
2016 (S.I. 2016:1101)
• Electromagnetic Compatibility Regulations
2016 (S.I. 2016:1091)
• The Restriction of the Use of Certain
Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
(S.I. 2012:3032)
and conforms to the following harmonized
standards:
• EN 55014-1:2021
• EN 55014-2:2021
• IEC 60745-1:2009+A11:2010
• EN IEC 63000:2018
• EN 60335-2-29:2004+A2:2010
• EN 60335-1:2012
• EN 62233-1:2008
U.K. Declaration of Conformity* DOCUMENT NUMBER
UK425014CA
Manufacturer name/address:
Lincoln Industrial Corporation
5148 N. Hanley Road
St. Louis, MO 63134 U.S.A.
TEL: [phone] FAX: [phone]
Authorized to compile the technical file:
SKF (U.K.) Limited
2 Canada Close
Banbury, Oxfordshire, OX16 2RT, GBR
EMAIL: [e-mail] WEBSITE: www.skf.com
I, the undersigned of Lincoln Industrial Corporation, hereby declare that the equipment specified above, in its intended use, conforms with all
requirements of the U.K. legislation Supply of Machinery (Safety) Regulations 2008 No. 1597 by the time of placing it on the market.
___________________________________
Robert Collins
Technical Compliance Manager
St. Louis, MO, U.S.A.
2022/11/03
And conforms to RoHS, states that homoge-
neous material levels are less than or equal
to 0.1% by weight:
The manufacturer maintains a technical
construction file containing test reports and
product documentation:
Technical file summary sheet number:
RA425014
*Indicates change.
4

Safety*
The assembly must be installed, maintained
and repaired exclusively by persons familiar
with the instructions.
Always disconnect power source
(electricity, air or hydraulic) from the
equipment when it is not being used.
This equipment generates high pressure.
Extreme caution should be used when
operating this equipment as material leaks
from loose or ruptured components can
inject fluid through the skin and into the
body. If any fluid appears to penetrate the
skin, seek attention from a doctor
immediately. Do not treat injury as a simple
cut. Tell attending doctor exactly what type of
fluid was injected.
Any other use not in accordance with
instructions will result in loss of claim for
warranty or liability.
• Do not misuse, over-pressurize, modify
parts, use incompatible chemicals, fluids,
or use worn and/or damaged parts.
• Do not exceed the stated maximum
working pressure of the equipment or of
the lowest rated component in your
system.
• Always read and follow the manufacturer’s
recommendations regarding fluid
compatibility, and the use of protective
clothing and equipment.
• Failure to comply may result in personal
injury and/or damage to equipment.
WARNING
Do not allow any body part
to be trapped by equipment.
Body parts can be crushed
by subassemblies during
operation.
Failure to comply may result in death
or serious physical injury.
WARNING
Do not allow fluid to leak
onto floor when operating
equipment. If spill occurs,
clean any fluid on floor before continuing
operation.
Failure to comply may result in death
or serious personal injury.
WARNING
Do not use this equipment to supply,
transport, or store hazardous
substances and mixtures in accordance
with annex I part 2-5 of the CLP
regulation (EG 1272/2008) or HCS 29
CFR 1910.1200 marked with GHS01,
GHS06 and GHS08 hazard pictograms
shown:
CAUTION
Avoid looking directly into
the light.
Failure to comply may
lead to a minor personal
injury.
Explanation of signal
words for safety
NOTE
Emphasizes useful hints and
recommendations as well as
information to prevent property damage
and ensure efficient trouble-free
operation.
CAUTION
Indicates a dangerous situation that can
lead to light personal injury if
precautionary measures are ignored.
WARNING
Indicates a dangerous situation that
could lead to death or serious injury if
precautionary measures are ignored.
DANGER
Indicates a dangerous situation that will
lead to death or serious injury if
precautionary measures are ignored.
WARNING
Do not operate equipment
without reading and fully
understanding safety
warnings and instructions.
Failure to follow warnings and
instructions may result in serious injury.
CAUTION
Do not operate equipment without
wearing personal protective gear.
Wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing pro-
tection used for appropriate conditions
will reduce personal injuries.
Failure to comply may result in light
personal injury.
*Indicates change.
55

Intended use
This PowerLuber was exclusively designed
to pump and dispense lubricant using 12 V
battery power. Do not exceed the maximum
specification ratings.
General power tool
safety warnings
Save all warnings and instructions for
future reference. The term “power tool” in
the warnings refers to your mains-operated
(corded) power tool or battery-operated
(cordless) power tool.
Safety instructions
Work area safety
• Keep work area clean and well lit. Clut-
tered or dark areas invite accidents.
• Do not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may
ignite the dust or fumes.
• Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
Personal safety
• Stay alert, watch what you are doing
and use common sense when
operating a power tool. Do not use a
power tool while you are tired or under
the influence of drugs, alcohol or medi-
cation. A moment of inattention while
operating power tools may result in seri-
ous personal injury.
• Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hardhat, or hearing protec-
tion used for appropriate conditions will
reduce personal injuries.
• Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or bat-
tery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools
that have the switch on invites accidents.
• Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in per-
sonal injury.
• Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unex-
pected situations.
• Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
• If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
WARNING
Read all safety warnings and
instructions. Failure to follow
the warnings and instructions
may result in electric shock,
fire and/or serious injury.
Electrical safety
• Power tool plugs must match the out-
let. Never modify the plug in any way.
Do not use any adapter plugs with
earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
• Avoid body contact with earthed or
grounded surfaces such as pipes, radia-
tors, ranges and refrigerators. There is
an increased risk of electric shock if your
body is earthed or grounded.
• Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
• When operating a power tool out-
doors, use an extension cord suitable
for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
• If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
6

Power tool use and care
• Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job bet-
ter and safer at the rate for which it was
designed.
• Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be repaired.
• Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally
• Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tool is dangerous in the hands of
untrained users.
• Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
• Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
• Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
Battery tool use and care
• Recharge only with the battery charger
specified by the manufacturer. A charger
that is suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
• Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create risk of
injury and fire.
• When battery pack is not in use, keep it
away from other metal objects, like
paper clips, coins, keys, nails, screws or
other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
• Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
Liquid ejected from battery may cause
irritation or burns. If contact acciden-
tally occurs, flush with water. If liquid
contacts eyes, seek medical help. Liquid
ejected from the battery may cause irrita-
tion or burns.
Service
Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
Safety of others
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruc-
tion concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Specific safety
• Always wear eye protection. The PowerLu-
ber can generate up to 689 bar
(10,000 psi). Use only Lincoln 1218, 1224,
1230 or 1236 outlet whip hoses. Grease
injection injuries are a very serious injury.
Hold the hose only in the area of the
spring guard. Avoid accidental starting. Be
sure switch is not depressed when insert-
ing battery pack. Replace the hose at the
first sign of wear, kink or damage to the
outside jacket.
• Do not bend the hose so that it becomes
kinked.
• Do not overreach. Keep proper footing and
balance at all times. Proper footing and
balance enable better control of the tool in
unexpected situations.
• Use safety equipment. Always wear eye
protection.
• Dust mask, non-skid safety shoes, hard
hat or hearing protection must be used for
appropriate conditions.
• The gun uses lubricants, that may be
flammable and poisonous if ingested.
Do not use gun near open flame or other
fire hazards.
• Greases are often marketed as high
temperature because it must maintain
their lubricating properties in hot areas,
but the lubricants may be flammable if the
temperature is too high. Please read all
warnings on lubricants before using this
gun. Do not use flammable greases with
this grease gun.
7

Residual risks
Additional residual risks may arise when
using the tool which may not be included in
the enclosed safety warnings.These risks
can arise from misuse, prolonged use, etc.
Even with the application of the relevant
safety regulations and the implementation
of safety devices, certain residual risks can
not be avoided. These include:
• Injuries caused by touching any rotating/
moving parts.
• Injuries caused when changing any parts,
blades or accessories.
• Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust
developed when using your tool (example:
working with wood, especially oak, beech
and MDF.)
Vibration
The declared vibration emission values
stated in the technical data and the declara-
tion of conformity have been measured in
accordance with a standard test method
provided by EN 62841 and may be used for
comparing one tool with another.
The declared vibration emission value
may also be used in a preliminary assess-
ment of exposure.
When assessing vibration exposure to
determine safety measures required by
2006/42/EC to protect persons regularly
using power tools in employment, an
estimation of vibration exposure should
consider the actual conditions of use and the
way the tool is used, including taking
account of all parts of the operating cycle
such as the times when the tool is switched
off and when it is running idle in addition to
the trigger time.
Labels on tool
The following symbols are shown on the
tool.
WARNING
Do not use tool before reading
instruction manual to reduce
risk of injury.
WARNING
Do not perform maintenance on tool
with battery installed.
Do not clean charger with it plugged
in.
WARNING
Vibration emission value during actual
use of power tool can differ from
declared value depending on ways in
which the tool is used. Vibration level
may increase above level stated.
WARNING
Do not use any hose not approved by
Lincoln. Extreme pressure may cause
nozzle extension or whip hose to burst.
Replace hose at first sign of wear,
kinks, or damage to outside jacket.
Follow whip hose instructions and
warnings. Failure to comply may result
in serious injury or death.
WARNING
Grease gun can develop high pressure
up to 689 bar (10,000 psi). Use safety
glasses and gloves for protection during
operation. Keep hands clear of exposed
rubber portion of hose. NOTE
Regularly clean ventilation slots in tool
and charger using a soft brush or dry
cloth.
Regularly clean motor housing using
a damp cloth. Do not use any abrasive
or solvent-based cleaner.
Regularly open chuck and tap it to
remove any dust.
Maintenance
The PowerLuber has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satis-
factory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any main-
tenance apart from regular cleaning.
8

Protecting the
environment
Should you find one day that your Lincoln
product needs replacement, or if it is of no
further use to you, do not dispose of it with
household waste. Make this product avail-
able for separate collection.
Local regulations may provide for sepa-
rate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
Safety instructions
for battery and
charger
Save these instructions
This manual contains important safety and
operating instruction for the Lincoln model
1870E battery charger.
Read all instructions
Batteries
• Never attempt to open for any reason.
• Do not expose the battery to water.
• Do not store in locations where the tem-
perature may exceed 40 °C (105 °F) such
as outside sheds or metal buildings in the
summer.
• Charge only at ambient temperatures
between 10 and 40 °C (50 and 104 °F).
• Charge only using the charger provided
with the tool.
• When disposing of batteries, follow the
instructions given in the section Protecting
the environment.
NOTE
Separate collection. Do not
dispose of with normal
household waste.
NOTE
Separate collection of used products
and packaging allows materials to be
recycled and used again.
Reuse of recycled materials helps
prevent environmental pollution and
reduces the demand for raw materials.
NOTE
Run battery down completely
and remove from tool.
NiCd, NiMH and Li-Ion
batteries are recyclable.
Take to any authorized repair agent or
local recycling.
NOTE
Do not attempt to charge damaged
batteries.
NOTE
Do not expose battery to
fire.
DANGER
Do not probe with conductive objects.
Do not charge damaged battery.
Replace immediately.
Risk of electric shock 230 V AC pres-
ent at charger terminals.
Failure to comply may result in seri-
ous injury or death.
DANGER
Never attempt to open battery pack for
any reason. If plastic housing of battery
pack breaks or cracks, return to a ser-
vice center for recycling.
Failure to comply may result in seri-
ous injury or death.
DANGER
Do not expose battery to spark or flame.
Battery liquid may burn.
Do not splash or immerse in water or
other liquids.This may cause premature
cell failure.
Failure to comply may result in seri-
ous injury or death.
9

NOTE
Charger is double insulated
and no ground wire is required.
Check mains voltage corre-
sponds to voltage on rating
plate. Never attempt to replace charger
unit with a regular mains plug.
Charger
• Before using a battery charger, read all
instructions and cautionary markings on
battery charger, battery pack, and product
using battery.
• Do not expose charger to rain, snow or
frost.
• Do not abuse cord. Never carry charger by
cord or pull on it to disconnect from recep-
tacle. Pull by plug rather than cord when
disconnecting charger. Have damaged or
worn power cord and strain reliever
replaced immediately. Do not attempt to
repair power cord.
• Locate cord so that it will not be stepped
on, tripped over, or otherwise subjected to
damage or stress.
• Do not use an extension cord unless
absolutely necessary. Use of improper
extension cord could result in a risk of fire
and electric shock.
• Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way, take it to a qualified
service center.
• Do not disassemble charger or battery
pack. Take it to a qualified service center
when service or repair is required.
Incorrect reassembly may result in risk of
electrical shock or fire.
• Unplug charger from outlet before
attempting any cleaning to reduce risk of
electric shock.
• Charge the battery pack in a well venti-
lated place; do not cover the charger and
battery with anything while charging.
• Do not store the charger or battery packs
in locations where the temperature may
reach or exceed 50 °C (122 °F) such as a
metal tool shed, or a car in the summer.
High temperatures can lead to deteriora-
tion of the storage battery.
• Do not charge battery pack when the tem-
perature is below 5 °C (40 °F) or above
40 °C (105 °F). This is very important for
proper operation.
• Do not incinerate battery pack. It can
explode in a fire.
• Do not charge battery in damp or wet
locations.
• Do not short across the terminals of the
battery pack. Extremely high tempera-
tures could cause personal injury or fire.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge.
• The Lincoln model 1261 battery pack con-
tains rechargeable, lithium-ion batteries.
Batteries must be recycled or disposed of
properly.
• Drop off expended battery packs at your
local replacement battery retailer, or your
recycling center.
CAUTION
Do not charge Lincoln model 1261
battery packs with any other charger.
Do not charge any other type of
battery with the 1870E battery charger.
Other types of batteries may burst.
Do not clean charger with it plugged
into electrical outlet.
Failure to comply may result in seri-
ous personal injury.
NOTE
Charger is intended for
indoor use only.
NOTE
Read instruction manual
before use.
Time-lag miniature
fuze link, 2A
IEC
IEEE/ANSI
IEEE/ANSI
Electrical safety
If the supply cord is damaged, it must be
replaced by the manufacturer or an author-
ized Lincoln service center in order to avoid a
hazard.
10

Specifications
Basic PowerLuber model 1260
Operating power 12 V
Grease reservoir capacity 411 g (14.5 oz)
Maximum pressure 551 bar (8,000 psi)
Operating temperature range –10 to +50 °C (15 to 120 °F)
Operating current 4 –40 A
Rated current 5A
Lubricant (grease) up to NLGI #2
Grease output 76,3 g/min (2.6 oz/min)
Weight 2,86 kg (6.3 lb)
Accessories
Battery li-ion Model 1261
Output 12 V
Capacity 1 500 mAh
Battery charger (E) Model 1870E TYPE 2
Charge time 40 minutes
Input 220 – 240 V AC, 0.6A, 50/60 Hz
Outlet hose Model 1230
Pressure rating 517 bar (7,500 psi)
Length of hose 762 mm (30 in)
Sound pressure Lp 66,0 dB(A), uncertainty (K) 3dB(A), acoustic power Lw 77,0 dB(A), vibration
emission value (ah) 0,4 m/s2, uncertainty (K) 1,5 m/s2
Models
Sales model Components included
1262E Grease gun with battery, 230V AC charger European and carrying case
1870E 220 – 240 V AC charger European
1261 Battery pack
1230 762 mm (30 in) hose
251-10124-7 European coupler
Tool use and care
• Do not continue to hold down trigger if
grease gun is stalled. This could damage
the motor or cause fire.
• Disconnect battery pack from tool before
making any adjustments, changing acces-
sories, or storing the tool. Such preventive
safety measures reduce the risk of starting
the tool accidentally.
• Store the tools out of reach of children and
other untrained persons. Tools are dan-
gerous in the hands of untrained users.
• If damaged, have the tool serviced before
using. Many accidents are caused by
poorly maintained tools.
• Use only accessories that are recom-
mended by Lincoln.
• Do not use any accessory that is not capa-
ble of handling 689 bar (10 000 psi).
Accessories that may be suitable for one
tool may create a risk of injury when used
on another tool.
11

1
2
3
4
5
6
7
8
General description
Lincoln’s 1260 PowerLuber is a lithium-ion
battery-operated grease gun developed for
manual lubrication of grease points.
Driven by a small, low-voltage electric
motor that is connected to a gear transmis-
sion. Rotary motion of the motor is con-
verted into a reciprocating motion of the
plunger, using a yoke mechanism. This
PowerLuber is a positive displacement single
acting pump.
Technology incorporated into the 1260
series PowerLuber includes:
• Motor protection preventing overload due
to excessive current draw
• Battery charge indicator displays battery
charge
• An LED to help locate grease fittings in dim
light
Inspection
Visually inspect for damaged, loose or miss-
ing parts. If equipment is worn or damaged,
remove from service. Contact an authorized
service center for damage assessment or
repair.
Operation
LED
• Tool’s trigger turns on LED and motor.
• Short stroke of trigger turns on LED only.
• LED will turn off after 15 seconds, follow-
ing stop of the motor or trigger release.
Fig. 1
1260 series PowerLuber grease gun
Parts
Item no. Part
1 LED
2Filler nipple plug
3 Hose
4 Vent valve
5 Support
6 Battery/gauge indicator
7 Hose holder
8 Battery
12

Install grease cartridge
1
Unscrew the grease tube assembly from the
PowerLuber.
2 Pull back on the follower handle and latch
the follower rod groove into the slot on the
tube cap.
3 Remove the plastic cap from the grease car-
tridge and insert cartridge into the con-
tainer tube.
4 Remove the pull tab from the grease car-
tridge and screw the grease tube assem-
bly into the pump assembly.
5 Thread grease tube assembly back onto the
power head.
6 Release follower rod from slot. Purge air
from pump. Refer to Expel air pockets
(†page 11) for air purging instructions.
Replace grease cartridge or
refill tube
Prime the PowerLuber after each refill or
grease cartridge change.
1
To prime, operate the gun until grease flows
from hose.
2 Use vent valve († fig. 1, page 9) to expel air
pockets.
Priming instructions
1 Open vent valve (4) († fig. 1, page 9).
2 Operate the gun until grease flows from the
vent valve.
3 Close vent valve.
NOTE
Air pockets in cartridge lubricant cause
grease gun to lose prime.
Always open vent valve after replacing
cartridge. This allows air to escape from
cartridge and prime grease gun.
Prime PowerLuber after each refill or
grease cartridge change.
13

1)
Fill gun from bulk container
1 Remove pump assembly from grease tube
assembly.
2 Pack lubricant into cavity of the pump
assembly.
3 Insert the open end of the grease tube
assembly into lubricant. Slowly pull the
follower handle back while pushing the
grease tube assembly deeper into the
lubricant to prevent air pockets from being
pulled into the grease tube.
4 With the follower rod fully extended, pull it
sideways to latch the rod groove into the
slot in the grease tube assembly cap.
5 Loosely assemble the pump to the grease
tube assembly. Release the follower rod
from the grease tube assembly cap and
disengage the follower rod from the fol-
lower by rotating the follower handle.
6 Push the follower rod into the grease tube
assembly.
7 Unscrew the grease tube assembly from the
pump until lubricant oozes from the inter-
face. Tighten grease tube assembly into
the pump assembly.
Fill gun with filler pump
1 Engage the follower rod with the follower by
rotating the follower handle.
2 Insert the gun bulk fill valve into the filler
pump socket.
3 Operate the filler pump to fill the container.
When the follower rod groove is exposed,
the grease tube assembly is filled.
The follower rod will be extended approxi-
mately 20 cm (8 in). Do not overfill!
4
Disengage the follower rod from the follower
by rotating the follower handle.
5 Push the follower rod into the grease tube
assembly.
Expel air pockets (air
purging)
1 Withdraw the follower rod from the grease
tube assembly cap and engage it with the
follower by rotating the follower handle.
2 Unscrew the plug of vent valve three to four
turns. Exert force on the follower handle
until grease flows through the small hole
in the side of the vent valve.
3 Tighten the vent valve.
4 Pull the trigger in short bursts to operate
gun until trapped air is expelled.
Disengage the follower rod from the
follower by rotating the follower handle.
Push the follower rod into the grease tube
assembly.
5 If step 2 fails, unscrew the grease tube
assembly three turns from the pump
assembly.
6 Exert force on the follower handle until
lubricant oozes from the grease tube
assembly and pump assembly interface.
7 Retighten grease tube into the pump assem-
bly. Disengage the follower rod from the
follower by rotating the follower handle.
Push the follower rod into the grease tube
assembly.
NOTE
Remove air pocket! Air pocket at grease
inlet prevents grease from being
pumped.
Unscrew vent valve three to four turns
to remove small air pockets trapped in
this area. If air pocket is substantial and
no grease flows from coupler after trig-
ger is pulled for 15 seconds, refer to
following steps, Expel air pockets.
14

Indicator light operation
Charge is complete (solid
green)
Battery charging (flashing
green)
Red, at a fast rate.
Replace battery
Charger detected a weak or
damaged battery. Stop
charging battery. Hot/cold
pack delay.
Charger detected a battery
that is excessively hot or
cold. It automatically starts a
hot/cold pack delay, sus-
pending charging until tem-
perature of battery has nor-
malized. After this, charger
automatically switches to
battery charging mode.
Charger operation
Charging battery pack
Before using the PowerLuber for the first
time, the battery pack should be fully
charged. If the battery pack is installed in the
PowerLuber, remove it and follow charging
procedure.
Lincoln chargers are designed to charge
Lincoln lithium-ion batteries in 30 to 90
minutes depending on the battery’s state of
charge and temperature.
Charging procedure
Do not use charger with any voltage other
than what is shown on the charger specifica-
tion plate.
1 Plug charger into an appropriate outlet
before inserting battery pack.
2 Insert battery pack into the charger.
The green (charging) light will blink
continuously indicating that the charging
process has started.
3 Completion of charge is indicated by green
light remaining on continuously. The pack
is fully charged and may be used at this
time.
4
Disconnect charger from power source when
not in use.
Important charging notices
Longest life and best performance can be
obtained if the battery is charged when the
air temperature is between 18 and 24 °C
(65 and 75 °F). Do not charge the battery in
an air temperature below 5 °C (40 °F) or
above 41 °C (105 °F). This is important and
will prevent serious damage to the battery.
1
The charger and battery may become warm
to the touch while charging. This is a nor-
mal condition, and does not indicate a
problem.
2 If the battery does not charge properly:
2.1 Check current at receptacle by plugging in
a lamp or other appliance.
2.2 Check to see if the receptacle is
connected to a light switch which
turns power off when you turn out the
lights.
2.3 Move charger and battery to a location
where the surrounding air tempera-
ture is between approximately
18 and 24 °C (65 and 75 °F).
2.4 If charging problems persist, take the tool,
battery and charger to your local ser-
vice center.
3 The battery should be recharged when it
fails to produce sufficient power on jobs.
Do not continue to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire, with no adverse
affect on the battery.
4 Under certain conditions, with the charger
plugged into the power supply, the
exposed charging contacts of the charger
can be shorted by foreign material.
Foreign materials of a conductive nature
such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from
charger cavities. Always unplug the
charger from the power supply when
there is no battery in the cavity.
Unplug charger before attempting to
clean.
CAUTION
Do not probe charger with conductive
objects 230 V AC present at charging
terminals.
Failure to comply may result in death
or personal injury.
NOTE
Do not charge battery immediately after
use. Battery will not accept a full charge.
Do not charge until battery has
reached room temperature for best
results.
NOTE
Do not obstruct vent slots in top and
bottom of charger.
Do not charge battery when tempera-
ture is below 5 °C (40 °F) or above 40 °C
(104 °F).
WARNING
Do not allow any liquid inside charger.
Electric shock may result.
To facilitate cooling of battery pack
after use, avoid placing charger or
battery pack in a warm environment
such as a metal shed or a non-insulated
trailer.
Failure to comply may result in
serious injury or death.
15

1
2
3
4
5
6
7
8
9
10
11
Parts list
No. Part no. Description
1 280213 Hardware kit (1260)
2 280244 Pump assembly kit (1262E)
3 1230 Hose, 3,1 mm ID x 762 mm long
(0.125 in ID x 30 in long)
4 280235 Trigger, switch kit
5 280211 Decal kit
6 280210 Handle with screws kit
7 1261 Battery
8 251-10124-7 Midget coupler
9 280209 Electrical components kit
10 271882 Grease tube kit
11 280233 Seal kit (1260)
Fig. IPB 1
Exploded view and parts list
16

12
13
14
15
16
17
18
Fig. IPB 2
Exploded view and parts list
Parts list
No. Part no. Description
12 280212 Housing with bearing kit
13 280245 Motor kit (1262E)
14 280214 Gear set kit (1260)
15 280215 Piston, yoke kit
16 280232 Driver assembly kit
17 280231 Check valve kit
18 286315 Vent valve kit
17

Troubleshooting
Condition Possible cause Corrective action
PowerLuber fails to dispense grease. Grease tube assembly is out of grease. Check that grease tube assembly has grease.
Loss of prime. Repeat priming operation.
Ball check is not functioning. Remove ball check clean and inspect ball seat area.
Clogged whip hose. Clean or replace whip hose.
PowerLuber continues to lose prime. Air may be trapped in several locations in container
after bulk filling.
Empty grease tube assembly, refill and repeat
priming instructions.
Follower may be binding in grease tube assembly. Disassemble grease tube assembly and clean.
Be sure that follower has properly entered the
grease cartridge.
Verify that the follower is not caught on the rim of
the grease cartridge.
Replace grease tube assembly (5) if damaged.
Check ball seat and check ball dirty. Clean check ball and check ball seat.
Battery fails to take a charge. Charger may not have power. Check that receptacle has power.
Battery may be bad. Replace battery.
Motor fails to run. Battery needs charging. Recharge battery.
Faulty wiring to motor. Remove battery, disassemble handle and check
wiring connections on terminal, trigger switch and
motor.
Parts list
No. Part no. Description
1 280213 Hardware kit (1260)
2 280244 Pump assembly kit (1262E)
3 1230 Hose, 3,1 mm ID x 762 mm long
(0.125 in ID x 30 in long)
4 280235 Trigger, switch kit
5 280211 Decal kit
6 280210 Handle with screws kit
7 1261 Battery
8 251-10124-7 Midget coupler
9 280209 Electrical components kit
10 271882 Grease tube kit
11 280233 Seal kit (1260)
12 280212 Housing with bearing kit
13 280245 Motor kit (1262E)
14 280214 Gear set kit (1260)
15 280215 Piston, yoke kit
16 280232 Driver assembly kit
17 280231 Check valve kit
18 286315 Vent valve kit
19 1870E Charger (European) 12–20 V (Li-Ion)
18

skf.com | lincolnindustrial.com
® SKF and Lincoln are registered trademarks of the SKF Group.
© SKF Group 2023
The contents of this publication are the copyright of the publisher and may not be reproduced (even
extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy
of the information contained in this publication but no liability can be accepted for any loss or damage
whether direct, indirect or consequential arising out of the use of the information contained herein.
February 2023 · Form 425014 Version 2
Warranty
The instructions do not contain any information on the warranty.
This can be found in the General Conditions of Sales, available at:
www.lincolnindustrial.com/technicalservice or www.skf.com/lubrication.