Linear Mini-Code 3060 User manual

location of both the transmitter and receiver will affect
the range. If the transmitter is stowed well out of sight, it
may be necessary to remove it from its mounting and
hold near the windshield. Try different locations and
positions. If operation is still unsatisfactory, the problem
may be isolated by:
1 . Checking the door operator. If the door will not
open when the wall button is pressed, the problem
is likely to be the operator. If the door will open by
pressing the wall button, but not when the radio
control button is pressed, the problem is probably in
the radios.
2. Replacing the transmitter battery. If, after perform-
ing the above operational checks, the controls still
do not function, they should be returned to your
dealer for repair or replacement.
CAUTION:
Any changes or modifications in intentional or
unintentional radiators which are not expressly approved by
LINEAR CORPORATION could void the user’s authority to
operate this equipment. This applies to intentional and
unintentional radiators certified per part 15 of the F.C.C.
rules and regulations.
This device complies with FCC Part 15 and Industry Canada
Rules and Regulations. Operation is subject to the following
two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
LINEAR CORPORATION
2055 Corte Del Nogal •Carlsbad, CA 92009
Copyright © 2000 Linear Corporation 214942 B
INSTALLATION INSTRUCTIONS
MINI-TRANSMITTER MODEL 3060
Congratulations! You have just purchased a Mini-Code
Digital Transmitter, which we believe to be the finest
product of its kind on the market. With a little care this
transmitter should provide you with many years of
excellent service. Please take a moment to read the
following instructions and you will find that setting your
new transmitter will be quite an easy matter.
ACCESSING THE CODE SWITCH AND BATTERY
COMPARTMENT
The model 3060 Mini-Transmitter case is composed of 2
halves which are held together by a small phillips head
screw. Removing this screw will allow access to both the
code setting switch and the battery compartment. (see
diagram #1)
INSTR,INSTL,MC3060,MINI-TX
LINEAR P/N: 214942 B
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 6.250" x 4.500"
SCALE: 1-1
SIDE 1 OF 2
®

SELECTING A CODE
Set both transmitter and receiver switches to the code of
your choice, being sure both are set the same since a
different setting of just one switch will prevent
operation. The digital code is determined by the position
of 10 small switches numbered 1 through 10 located in
the receiver and transmitter. Any combination of “on”or
“off”positions can be selected by using a pencil or ball
point pen. (Note: The switches are in the “on”position
when the switch is depressed toward the number.) See
diagram # 2.
Once the codes have been set, check operation and
reassemble the transmitter case.
MINI-TRANSMITTER INSTALLATION
This transmitter is completely self contained, including
battery and can be operated while held in hand or while
mounted in the car. It is supplied with “hook and loop”
fabric for easy mounting or it may be added to your key
chain using the slot provided.
TRANSMITTER BATTERY REPLACEMENT
Replacement battery - 12 volt alkaline lighter battery
(Eveready A 23 or equivalent)
The transmitter battery can be checked or changed by
removing the phillips head screw located on the back of
the case and carefully separating the case halves to
expose the circuit board and battery. Simply slide out the
old battery and slide in the new, remembering to observe
the battery polarity molded on the case in the bottom of
the battery compartment. Note that if the red L.E.D. on
your transmitter fails to light you most likely have a weak
or dead battery and it should be replaced. (see diagram
#1)
OPERATIONAL CHECK
To check operation, move back a reasonable distance
(about 50 ft.) and press the transmitter button. Operation
should be reliable at this distance but environment and
INSTR,INSTL,MC3060,MINI-TX
LINEAR P/N: 214942 B
INK: BLACK
MATERIAL: 20 LB. MEAD BOND
SIZE: 6.250" x 4.500"
SCALE: 1-1
SIDE 2 OF 2
BATTERY
TRANSMITTER WITH TOP
HAL F OF CASE REMOVED
DIAGRAM #1
TRANSMITTER TOP COVER
CODE
SWITCH
123456789
1
0
ON
OFF
CODE SWITCH
DIAGRAM #2