Linksys CM30XX User manual

User Guide
Cable Modem
CM30XX
1

Contents
PRODUCT OVERVIEW....................................................................................................................... 4
Front view .................................................................................................................................................................................4
CM3008 ...............................................................................................................................................................................4
CM3016/CM3024 ...........................................................................................................................................................5
Back/Bottom view..................................................................................................................................................................6
CM3008 ...............................................................................................................................................................................6
CM3016/CM3024 ...........................................................................................................................................................6
INSTALLING YOUR MODEM............................................................................................................ 8
Requirements ..........................................................................................................................................................................8
Getting a high-speed Internet account......................................................................................................................8
If you already have a high-speed Internet account................................................................................................8
Modem information...........................................................................................................................................................8
Positioning your modem.......................................................................................................................................................9
SETTING UP YOUR MODEM......................................................................................................... 10
Connect devices to the modem......................................................................................................................................10
TROUBLESHOOTING ...................................................................................................................... 12
How do I renew the IP address on my computer?....................................................................................................12
To renew the IP address on Windows 7 systems:............................................................................................... 12
To renew the IP address on Windows XP systems: ............................................................................................ 12
Renewing the IP address on Macintosh systems................................................................................................ 12
What if I don’t subscribe to cable TV?..........................................................................................................................13
How do I arrange for installation? .................................................................................................................................13
How does the modem connect to my computer?.....................................................................................................13
After my modem is connected, how do I access the Internet? ...........................................................................13
Can I watch TV and surf the Internet at the same time?.......................................................................................13
2

The modem does not register an Ethernet connection..........................................................................................13
The modem does not register a cable connection...................................................................................................14
Tips for improved performance...................................................................................................................................... 14
Check and correct .......................................................................................................................................................... 14
SPECIFICATIONS ............................................................................................................................. 15
CM3008................................................................................................................................................................................. 15
CM3016................................................................................................................................................................................. 17
CM3024................................................................................................................................................................................. 19
3

Product Overview
Front view
CM3008
Reset Button------Press and hold for five seconds to restore settings to factory defaults and reboot
the modem.
Ethernet LED------Green (Fast Ethernet). Blue (Gigabit Ethernet). A solid LED indicates something is
plugged into the Ethernet port and the connection is operational. A blinking LED indicates data is
being transferred over the Ethernet connection. If the LED is off nothing is connected to the Ethernet
port or a connected device has been disabled by the user.
Status LED------LED blinks while the modem is registering a connection over the cable network. A solid
LED indicates the modem is connected to the cable network.
Send LED------LED blinks green while the modem is searching for a connection over the cable network.
A solid green LED indicates the modem is sending data to the cable network. A solid blue LED indicates
multi-channel bonding.
Receive LED------A solid green LED indicates the modem is receiving data from the cable network. A
solid blue LED indicates multi-channel bonding.
Power LED------ The modem has power.
4

CM3016/CM3024
Power LED------ The modem has power.
Receive LED------A solid green LED indicates the modem has a working Internet connection to the cable
network. A solid blue LED indicates multi-channel bonding.
Send LED------LED blinks green while the modem is searching for a connection over the cable network.
A solid green LED indicates the modem has a working Internet connection to the cable network. A solid
blue LED indicates multi-channel bonding.
Status LED------LED blinks while the modem is registering a connection over the cable network. A solid
LED indicates the modem has a working Internet connection.
Ethernet LED------ Green (Fast Ethernet). Blue (Gigabit Ethernet). A solid LED indicates another device
is plugged into the Ethernet port, and turned on, and the connection is operational. A blinking LED
indicates data is being transferred over the Ethernet connection. If the LED is off nothing is
connected to the Ethernet port or a connected device has been disabled by the user.
5

Back/Bottom view
CM3008
Power Port------ Connect the included AC power adapter to this port.
Ethernet Port------ Connect an Ethernet cables (also called network or Internet cables) to this port
and to your computer or a router.
Cable Port------F-connector connects to an active cable signal from your wall jack to your modem.
CM3016/CM3024
Reset Button------Press and hold for five seconds to restore settings to factory defaults and reboot
the modem.
6

Ethernet Port------ Connect an Ethernet cables (also called network or Internet cables) to this port
and to your computer or a router.
Cable Port------F-connector connects to an active cable signal from your wall jack to your modem
7

Installing Your Modem
Requirements
Before installing the modem, make sure that you meet the requirements listed below.
•An Internet-capable computer or router equipped with an Ethernet port
•An active cable input line
•An Internet connection from a service provider
Getting a high-speed Internet account
You will need a high-speed Internet account in order to use this modem. If you do not have a high-speed
Internet account, your service provider can set up your account for Internet service.
You will need to give your service provider information about the modem in order to get Internet access.
Refer to the label on the back or bottom of your modem for this information.
If you already have a high-speed Internet account
If you already have a high-speed Internet account, you will need to give your service provider the serial
number and MAC address of the modem. Refer to the label on the back of your modem for this
information. Your service provider may also ask for other account details, which you should have
available (account number, account holder phone number, login information).
Modem information
You will need to give your service provider the following information, which is printed on the bar code
label attached to the modem:
•The serial number of the modem. The serial number consists of a series of decimal characters
8

preceded by S/N.
•The CM Media Access Control (CM MAC) address of the modem. The CM MAC address consists
of a series of hexadecimal characters preceded by CM MAC.
•Other MAC address numbers as needed.
Positioning your modem
The ideal location for your modem is where it has access to outlets and your other devices.
Recommendations:
•Choose a location close to your computer or router.
•Choose a location that is near an existing RF coaxial connection
•Choose a location that is relatively protected from accidental disturbance or harm
•Choose a location with plenty of room for guiding the cables away from the modem without
straining or crimping them.
•Choose a location that allows adequate ventilation around the modem.
9

Setting Up Your Modem
Connect devices to the modem
Your modem supports high-speed Internet service, which you can share with other Internet devices in
your home or office. Sharing one connection among many devices is called networking.
1. Power off your computer and other networking devices, then unplug them from the power
source.
2. Connect an active RF coaxial cable from the wall to the cable port on the back or bottom of
the modem, depending on which model you have.
CM3008 CM3016/CM3024
3. Connect your computer or router to the modem by connecting one end of the yellow Ethernet
cable to the Ethernet port on your computer or router, and the other end to the yellow
Ethernet port on the back of the modem.
CM3008 CM3016/CM3024
10

Note—To install more than one Ethernet device, use a multiport Ethernet switch or a router
(not provided).
4. Locate the AC power adapter provided with your modem. Connect the barrel connector end of
the power adapter into the power port on the back of the modem. Then, plug the AC power
adapter into an AC outlet to provide power to the modem.
CM3008 CM3016/CM3024
Note—If your modem is equipped with a power switch (located on the back panel), make sure
that the switch is in the ON position to provide power to the modem.
5. The modem may reboot several times during this process and activation may take up to five
minutes. The modem will be ready for use when the LEDs on the front panel of the modem
stop blinking and remain on.
6. Plug in and turn on your computer and other home network devices at this time. The Ethernet
LED on the modem should be on or blinking.
7. The last step is to open a web browser and verify Internet access. Some service providers
have additional setup steps that will automatically appear in the browser. Follow the steps if
necessary or call your Internet Service provider if you are unable to get online.
Note—If your computer does not have Internet access, see “How do I renew the IP address on
my computer?” on page 12 for information on how to configure your computer for TCP/IP. For
Internet devices other than computers, see the DHCP or IP Address configuration section of
the user guide for those devices.
11

Troubleshooting
How do I renew the IP address on my computer?
If your computer cannot access the Internet after the modem is online, it is possible that your
computer did not renew its IP address.
To renew the IP address on Windows 7 systems:
1. Click the Start button.
2. Type ‘‘cmd’’ in the Search box. The cmd window opens.
3. Type ‘‘ipconfig /renew’’ and press Enter to renew the IP address of the computer.
Note—If you cannot access the Internet, contact your service provider for further assistance.
To renew the IP address on Windows XP systems:
1. Click Start, and then click Run. The Run window opens.
2. Type ‘‘cmd’’ in the Open field and click OK. A window with a command prompt opens.
3. Type ‘‘ipconfig /release’’ at the C:\ prompt and press Enter. The system releases the IP
address.
4. Type ‘‘ipconfig /renew’’ at the C:\ prompt and press Enter. The system displays a new IP
address.
5. Close the Command Prompt window. You have completed this procedure.
Note—If you cannot access the Internet, contact your service provider for further assistance.
Renewing the IP address on Macintosh systems
1. Click on System Preferences icon (in the Dock or in the Applications folder).
2. Click on Network icon.
3. Click on Advanced.
4. Click on TCP/IP tab.
5. Click Renew DHCP Lease and click on OK.
12

What if I don’t subscribe to cable TV?
If cable TV is available in your area, data service may be made available with or without subscribing to
cable TV service. Contact your local service provider for complete information on cable services,
including high-speed Internet access.
How do I arrange for installation?
Call your service provider to inquire about professional installation. A professional installation
ensures proper cable connection to the modem and to your computer, and it ensures the proper
configuration of all hardware and software settings. Contact your service provider for more
information about installation.
How does the modem connect to my computer?
The modem connects to the 1000/100BASE-T Ethernet port on your computer. For best
performance over an Ethernet connection, your computer should be equipped with a Gigabit Ethernet
port.
After my modem is connected, how do I access the Internet?
Your local service provider becomes your Internet Service Provider (ISP). They offer a wide range of
services including e-mail, chat, news, and information services. Open a web browser. Any additional
setup steps will automatically appear in the browser.
Can I watch TV and surf the Internet at the same time?
Yes. If you subscribe to cable television service, you can watch TV and use your modem at the same
time by connecting your TV and your modem to the cable network using an optional cable signal
splitter.
The modem does not register an Ethernet connection.
Verify that your computer has an Ethernet card and that the Ethernet driver software is properly
installed. If you purchase and install an Ethernet card, follow the installation instructions.
Verify the status of the front panel status indicator lights.
13

The modem does not register a cable connection.
The modem works with a standard, 75-ohm RF coaxial cable. If you are using a different cable, your
modem will not function properly. Contact your service provider to determine whether you are using
the correct cable.
Tips for improved performance
Check and correct
If your modem does not perform as expected, the following tips may help. If you need more help,
contact your service provider.
•Verify that the plug to your modem’s AC power is connected to a power source.
•If your modem’s AC power cord is plugged into an electrical outlet that is controlled by a wall
switch, make sure the switch is turned on.
•Verify that the modem’s Ethernet LED status indicator is on.
•Verify that your cable service is active and that it supports two-way service.
•Verify that all cables are properly connected and that you are using the correct cables.
•If you are using the Ethernet connection, verify that your TCP/IP is properly installed and
configured.
•Verify that you have called your service provider and given them the serial number and MAC
address of your modem.
•If you are using a cable signal splitter so that you can connect the modem to other devices,
remove the splitter and reconnect the cables so that the modem is connected directly to the
cable input. If the modem now functions properly, the cable signal splitter may be defective
and may need to be replaced.
•If you are connected to your computer with an Ethernet connection, your computer should be
equipped with a Gigabit Ethernet card for best performance.
14

Specifications
CM3008
Protocol Support •DOCSIS 1.1/2.0/3.0
•SNMP v1, v2C, v3
•DHCP, TFTP and ToD clients (IPv4/IPv6)
Connectivity •RF F-type female 75Ωconnector
•RJ-45 Ethernet port 10/100/1000 Mbps
(Auto-MDI/MDIX)
Management •Web-
based GUI control configuration and
management
•Dual-color LEDs clearly display network
status and activity
•Power on self-diagnostic
•MIB II/MCNS MIB
•Proprietary MIBs for extended support
Reception-Demodulation •Demodulation: 64QAM, 256QAM
•Data Rate: Up to 343 Mbps with 8
bonded downstream channels (DOCSIS)
•Frequency (edge-to-edge): 88 ~ 1002
MHz (DOCSIS)
•Channel Bandwidth: 6 MHz (DOCSIS)
•Signal Level: -15 dBmV to 15 dBmV
•Input return loss: >6dB
Transmitter-Modulation •Modulation: QPSK, 8QAM, 16QAM,
32QAM, 64QAM, and 128QAM (SCDMA
only)
•Data rate up to 122 Mbps with 4
upstream channel bonding
•Frequency: 5 ~ 42 MHz (DOCSIS)
•
Output return loss: >6dB
15

Mechanical •5 status LEDs (Power, DS, US, Status,
LAN)
•Factory default reset button
•Dimensions: 110mm(W) x 70mm(D) x
25mm(H)
•
Weight: 100g ± 10g
Environmental •Power Input DC: DC 12V/1A or 12V/2A
•Operating Temperature: 32°F (0°C) to
104°F (40°C)
•Operating Humidity: 10% ~ 90% (Non-
condensing)
•Storage Temperature: -40°F (-40°C) to
176°F (80°C)
Compliance Certificates •RoHS Compliant
•FCC, UL
16

CM3016
Protocol Support •DOCSIS 1.1/2.0/3.0
•SNMP v1, v2C, v3
•DHCP, TFTP and ToD clients (IPv4/IPv6)
Connectivity •RF F-type female 75Ωconnector
•RJ-45 Ethernet port 10/100/1000 Mbps
(Auto-MDI/MDIX)
Management •Web-
based GUI control configuration and
management
•Dual-color LEDs clearly display network
status and activity
•Power on self-diagnostic
•MIB II/MCNS MIB
•Proprietary MIBs for extended support
Reception-Demodulation •Demodulation: 64QAM, 256QAM
•Data Rate: Up to 686 Mbps with 16
bonded downstream channels
•Frequency (edge-to-edge): 108 ~ 1002
MHz (DOCSIS)
•Channel Bandwidth: 6 MHz
•Signal Level: -15 dBmV to 15 dBmV
•Input return loss: >6dB
Transmitter-Modulation •Modulation: QPSK, 8QAM, 16QAM,
32QAM, 64QAM, and 128QAM (SCDMA
only)
•Data rate up to 122 Mbps with 4
upstream channel bonding
•Frequency: 5 ~ 42 MHz
•
Output return loss: >6dB
Mechanical •5 status LEDs (Power, DS, US, Status,
LAN)
•Factory default reset button
•Dimensions: 177mm(W) x 204mm(D) x
45mm(H) / Stand included: 177mm (W) x
213.8mm (H) x 95.4mm (D)
•Weight: 500g ± 10g
17

Environmental •Power Input: DC 12V/2A
•Operating Temperature: 32°F (0°C) to
104°F (40°C)
•Operating Humidity: 10% ~ 90% (Non-
condensing)
•Storage Temperature: -40°F (-40°C) to
176°F (80°C)
Compliance Certificates •RoHS Compliant
•FCC, UL
18

CM3024
Protocol Support •DOCSIS 1.1/2.0/3.0
•SNMP v1, v2C, v3
•DHCP, TFTP and ToD clients (IPv4/IPv6)
Connectivity •RF F-type female 75Ωconnector
•RJ-45 Ethernet port 10/100/1000 Mbps
(Auto-MDI/MDIX)
Management •Web-based GUI control configuration and management
•Dual-color LEDs clearly display network status and activity
•Power on self-diagnostic
•MIB II/MCNS MIB
•Proprietary MIBs for extended support
Reception-Demodulation •Demodulation: 64QAM, 256QAM
•Data Rate: Up to 960 Mbps with 24 bonded downstream
channels
•Frequency (edge-to-edge): 108 ~ 1002 MHz
•Channel Bandwidth: 6 MHz
•Signal Level: -15 dBmV to 15 dBmV
•Input return loss: >6dB
Transmitter-Modulation •Modulation: QPSK, 8QAM, 16QAM, 32QAM, 64QAM, and
128QAM (SCDMA only)
•Data rate up to 122 Mbps with 4 or 8 upstream channel
bonding
•Frequency: 5 ~ 42 MHz (DOCSIS)
•
Output return loss: >6dB
Mechanical •5 status LEDs (Power, DS, US, Status, LAN)
•Factory default reset button
•Dimensions: 177mm(W) x 204mm(D) x 45mm(H) / Stand
included: 177mm (W) x 213.8mm (H) x 95.4mm (D)
•Weight: 500g ± 10g
Environmental •Power Input: DC 12V/2A
•Operating Temperature: 32°F (0°C) to 104°F (40°C)
•Operating Humidity: 10% ~ 90% (Non- condensing)
•Storage Temperature: -40°F (-40°C) to 176°F (80°C)
Compliance Certificates •RoHS Compliant
•FCC, UL
19

Notes
For regulatory, warranty, and safety information, and award-winning technical support, see the CD
that came with your router or go to Linksys.com/support/.
BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin group of
companies. Third-party trademarks mentioned are the property of their respective owners.
© 2016 Belkin International, Inc. and/or its affiliates. All rights reserved.
LNKPG-00293 Rev. B00
20