Little Tikes Reindeer Carriage User manual

ASSEMBLY INSTRUCTIONS
Reindeer Carriage™
XIM654879 - 8/20
1
Adult assembly required. Approx. assembly time: 50 min.
Look for video of assembly at
littletikes.com/videoinstructions
11
/2-5
#654879M
years

2
WARNINGS!
• Adult Assembly Required
• Keep these instructions for future reference.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard and
may contain sharp edges and sharp points. Keep away from children until assembled.
• Ride-on toys should not be used near swimming pools, on or near steps, hills, roadways, or
inclines.
• Shoes must be worn at all times.
• Only one rider at a time.
• Maximum weight limit: 50 lbs. (23 Kg)
• This product is intended for use by children ages over 1 1/2 - 5 years.
• Adult supervision required. Do not leave children unattended.
• Protect your eyes. Always wear safety glasses when using a hammer.
Thank you for choosing the Little Tikes©Reindeer Carriage™.
We strive to provide a durable, easy-to-assemble toy thats made to last,
giving your child years of imaginative, engaging fun!
• Read through all the instructions rst.
• Clear a at surface to lay out all the materials so everything is close at hand.
• You will need a Phillips head screwdriver, hammer and safety glasses (not included) to
assemble the Reindeer Carriage™.
- When installing screws, be sure screws are tightened snugly, but do NOT OVERTIGHTEN.
• Be sure to locate your decals and set aside. Decals are easier to apply when the part is
laying at, so you may want to apply the decals before assembly.
• The parts are listed below - each part is identied with a letter in RED for easy reference.
• Illustrations are for reference only. Styles may vary from actual contents.
• If you have any questions, we’re here to help. Give our customer service team a
call at 1-800- 321-0183.
Really important information you should know!

3
Tools required (not included)
(Recommended)
(Recommandé)
(Recomendado)
Included in hardware pack. Discard after use.
Tool color may vary.
Small cap nut tool
Axle cap toolTop hat tool
(7) 1" (2,54cm) (2) 3/4" (1,9cm)
Rear Handle Fastener (2)
Hardware Guide
Shown actual size
Small cap nut tool
Axle cap tool
Top hat (4) Axle cap (2) Small cap nut (2)
Washer (6)
Bushing (4)
DD
EE
Top hat tool
CC
BB
AA
Small Fastener (3)
(Clip-clop box - 1)
(Front carriage plugs - 2)
Jingle Bell Fastener (4)
Ear Bottom Fastener (2)
(4) 1/2" (1,27cm)

4
A Few Things Before You Start!
BEFORE you begin assembly, make sure
you have all the parts listed below.
Some packages of hardware may have extras pieces.
!
Questions? We’re here to help.
Little Tikes customer service team at 1-800- 321-0183.
!
Body (1)
Door (1)
Trunk lid (1)
Floorboard
buttons (2)
Door latch (1)
Dashboard (1)
Hooves (2)
A
B
C
D
E
F
G
Reindeer
body (1)
Rear
handle (1)
Clip-clop
box (1)
Clip-clop
arm (1)
Clip-clop
cups (2)
Front carriage
plugs (2)
Clip-clop gear (1)
Reins (1)
H
O
P
Q
S
T
N
I
Ear - top left (1)
Antler - left (1)
Ear - bottom
left (1)
Ear - top right (1)
Antler - right (1)
Ear - bottom
right (1)
J1
M1 M2
K1
J2
K2

5
Wheels (4)
U
Left Right
Front Wheel
Axles
L R
Large axle - rear wheel (1)
Small axle - reins (1)
X
Y
Center caps (4)
Floor board (1)
W
V
(1) Decal sheet
is located in the
hardware pack. Jingle bells (1)
Z
LIMITED WARRANTY
The LittleTikes Company makes fun, high quality toys.We warrant to the original purchaser that this product is free of defects in materials or workmanship for one year * from the date of purchase (dated sales receipt is
required for proof of purchase). At the sole election of The Little Tikes Company, the only remedies available under this warranty will be the replacement of the defective part or replacement of the product.This warranty is
valid only if the product has been assembled and maintained per the instructions.This warranty does not cover abuse, accident, cosmetic issues such as fading or scratches from normal wear, or any other cause not arising
from defects in material and workmanship. *The warranty period is three (3) months for daycare or commercial purchasers.
U.S.A and Canada: For warranty service or replacement part information, please visit our website at www.littletikes.com, call 1-800-321-0183 or write to: Consumer Service,The LittleTikes Company, 2180 Barlow Road,
Hudson OH 44236, U.S.A. Some replacement parts may be available for purchase after warranty expires—contact us for details.
Outside U.S.A and Canada: Contact place of purchase for warranty service.This warranty gives you specic legal rights, and you may also have other rights, which vary from country/state to country/state. Some countries/
states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
©The LittleTikes Company, an MGA Entertainment company. LITTLETIKES® is a trademark of LittleTikes in the U.S. and other countries. All logos, names, characters, likenesses, images, slogans, and packaging appear-
ance are the property of LittleTikes. Please keep this address and packaging for reference since it contains important information. Contents, including specications and colors, may vary from photos depicted on package.
Instructions included. Please remove all packaging including tags, ties & tacking stitches before giving this product to a child.
United States:
www.littletikes.com
1-800-321-0183 Monday - Friday
The LittleTikes Company
2180 Barlow Road
Hudson, OH 44236
E-mail: [email protected]
Printed in U.S.A. D.R.©2020The Little Tikes Company
United Kingdom:
www.littletikes.co.uk
LittleTikes, MGA Entertainment (UK) Ltd
50 PresleyWay
Crownhill
Milton Keynes MK8 0ES
Bucks, UK
Tel: [phone]
E-mail: [e-mail]
Australia
www.littletikes.com.au
Imported by MGA Entertainment Australia Pty Ltd
Suite 2.02, 32 Delhi Road
Macquarie Park NSW 2113
1 300 059 676
CONSUMER SERVICE:
MINIMUM SIZE allowed is .2” high
Updated 12.2.11 per Paul Madan (new spacing)

6
1
Ready...let’s start with decals!
Decals must be applied to a clean, dry surface. Wipe clean with a dry rag before application.
Remove air from under decals by applying pressure to the decals starting from the center, and
work towards edges. NOTE: If decals bubble, prick with a pin to remove the air.
Decals are located
in the bottom of
the cardboard box.
x4
13 x8 each wheel
Front side
12
78911 10
Front Rear
1
6
2
5
43

7
2
3a
Time to hoof it!
Fit a hoof (part G) onto each
leg on reindeer body.
Second, secure using (2)
1/2”(1,27cm) screws.
Ears First!!!
Place the ear bottom left (part K1) onto the
left side of the reindeer body head.
Second, secure the ear bottom using (1) ear
bottom fastener.
G
G
H
x2
1" (2,54cm)
K1
Left side
Ear Bottom Fastener (1)

8
J1
3b
3c
Ears First!!!
Place the ear top left (part J1) onto the ear bottom you just attached.
Second, secure the ear top behind the ear, using (1) 3/4”(1,9cm) screw.
NOW the antlers
Insert the antlers into the assembled EARS. Push them together. You will feel them
lock into each other. Once together they will NOT COME APART.
M1 M2
REPEAT steps 3a - 3b for RIGHT side
Back of ear
Antler - left Antler - right
3/4”(1,9cm)

9
4
Jingle bells, jingle bells...
Attach the jingle bells (part Z) using the (4) jingle bell fasteners.
Jingle Bell Fastener (4)
2
1
3
4

10
5
Attaching the reins
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
Small cap nut tool
CC
Place small cap nut (part CC) into
small cap nut tool.
Fit the reins (part I) onto the reindeer head.
Align the holes in the reins to the holes in
the head.
Insert the small axle (part Y) into
the cap nut.
Hammer the axle into the cap nut.
Y
Small axle
Really give it a good hit!
I
BEFORE THREADING the axle, it
helps to clear away any excess
plastic by poking the small axle
through the holes in the head.
Reins should
curve upward.
Thread the small axle through the reins
and head.
Small cap nut

11
5
Attaching the reins -
one more step
Flip reindeer and reins over.
Place the small cap nut (CC) and the
small cap nut tool over the OPEN end
of the axle.
Hammer the small cap nut onto axle.
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
CC Small cap nut
Small cap nut tool
6
Button up
Press oorboard buttons (part D) into the body.
D D

12
8
Rear Handle
Insert rear handle (part O) into the rear of the body aligning the holes in the handle to the
holes in the body. Insert (1) large fastener - each side and hammer into place.
7
Trunk lid
Fit trunk (part C) onto rear end of the carriage.
Beveled end should
be inserted SECOND
Rounded end should
be inserted FIRST
C
O
Large Fastener (2)
2
1

Clip-Clop...attach the cups
Once clip-clop cups are installed with screws,
they will wiggle.
1/2" (1,27cm) 1/2" (1,27cm) Top view
P
S
S
Q
Top view
Insert (1) clip-clop cup (part S) into the
clip-clop box (part P).
Attach using using (1) 1/2”(1,27cm) screw.
Insert (1) clip-clop cup (part S) into the
clip-clop arm (part Q).
Attach using using (1) 1/2”(1,27cm) screw.
9
13
TT
Small Fastener
(Front carriage plugs - 2)
Plug the holes
Insert front carriage plugs (part T)
into the front of the carriage.
10

10
14
Place clip-clop arm into box. Insert so that
cups are facing each other forming a circle.
Insert pivot into holes.
Clip-Clop...attach the cups-cont.
Underside of the Rear of the Carriage
Small Fastener (1)
Flip the carriage over and t the clip-clop box into the opening at
the right rear wheel. Secure with a small fastener.

15
11
Rear wheels
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.
Top hat tool
AA
Place top hat (part AA) into
top hat tool.
Insert the large axle (part X) into
the top hat.
Hammer the axle into the top hat.
X
Large axle
Really give it a good hit!
Slide onto large axle (1) wheel (U),
clip-clop gear (N) and (1) washer (DD).
Clip-clop gear should t
into wheel.
NDD
U
wheel
washer
clip-clop gear
top hat

16
11
Rear wheels-cont.
Slide on washer
and wheel.
Slide assembled axle THROUGH the
clip-clop box and into rear axle guides.
NOTE: the clip-clop box remains loose
once the axle is installed.
AA
Axle cap tool
Top hat
Top hat tool
Use axle cap tool
to SUPPORT the
bottom of axle.
Flip carriage on its side.
Balance the assembled top hat end
on the axle cap tool.
Place a top hat (AA) and the top hat
tool over the OPEN end of the axle.
Hammer the top hat onto axle.
Do not hammer on
surfaces or items
you don’t want to
break, mar or dent.

17
12
Front wheels
Left Right
Axles are
NOT IDENTICAL.
L R
AA
Top hat
Top hat tool
REPEAT these steps for RIGHT front axle
DD washer
wheel
U
LEFT front axle
L
Slide onto LEFT
front axle (L) -
(1) wheel (U) and
(1) washer (DD).
Place top hat then
top hat tool onto
open end of axle.
Hammer top hat
onto axle.

18
IMPORTANT! Check axle positions - roll
the Reindeer Carriage forward - HUBCAPS
SHOULD FACING OUTWARD.
STOP
Slide (1) washer (DD) and
(1) bushing (EE) onto
right axle.
Slide (1) washer (DD) and
(1) bushing (EE) onto left
axle.
Insert axle“R” (for right)
into body.
Insert axle“L”(for left)
into body.
R L
DD DD
EE EE
washer washer
bushing bushing

19
BB
Axle cap
Axle cap tool
Insert (1) bushing onto each
axle and push it down in place.
Place top hat then top
hat tool onto open end
of axle. Hammer top
hat onto axle. Repeat
for other axle.
13
Cap it
Align slots in center cap (V) to slots on each wheel and snap into place.
Snap!
x4
EE
bushing

20
14
Door latch
Place door latch (part E) onto door (part B). Attach using using (1) 1/2”(1,27cm) screw.
1/2" (1,27cm)
E
B
15
Let’s put this all together
Insert asembled reindeer
body onto front of the
carriage.
Insert door onto carriage.