LMI Technologies 2020 User manual

USER’S MANUAL Gocator 2000 & 2300 Series
Version 3.5.2.143 Revision: B

2Gocator 2000 & 2300 Series
Copyright © 2012 by LMI Technologies, Inc. All rights reserved.
Proprietary
This document, submitted in confidence, contains proprietary information which shall not be reproduced
or transferred to other documents or disclosed to others or used for manufacturing or any other purpose
without prior written permission of LMI Technologies Inc.
No part of this publication may be copied, photocopied, reproduced, transmitted, transcribed, or
reduced to any electronic medium or machine readable form without prior written consent of
LMI Technologies, Inc.
Trademarks and Restrictions
Gocator™ is a registered trademark of LMI Technologies, Inc. Any other company or product names
mentioned herein may be trademarks of their respective owners.
Information contained within this manual is subject to change.
This product is designated for use solely as a component and as such it does not comply with the
standards relating to laser products specified in U.S. FDA CFR Title 21 Part 1040.
Contact Information
For more information, please contact LMI Technologies.
LMI Technologies, Inc.
1673 Cliveden Ave.
Delta, BC V3M 6V5
Canada
Telephone: [phone]
Facsimile: [phone]
www.lmi3D.com

3Gocator 2000 & 2300 Series
Introduction
The Gocator 2000 and 2300 series of laser profiling sensors are designed for 3D measurement and
control applications. Gocator sensors are configured using a web browser and can be connected to a
variety of input and output devices. This guide describes the installation and use of Gocator sensors.
Notational Conventions
This guide uses the following notational conventions:
!
Warning Follow these safety guidelines to avoid potential injury or property damage.
Note Consider this information in order to make best use of the product.

4Gocator 2000 & 2300 Series
Introduction 3
Table of Contents 4
Safety and Maintenance 9
Laser Safety 9
Laser Classes 10
Precautions and Responsibilities 11
Class 3B Responsibilities 11
Systems Sold or Used in the USA 12
Electrical Safety 13
Environment and Lighting 14
Sensor Maintenance 14
Getting Started 16
System Overview 16
Standalone System 16
Dual Sensor System 18
Multi-Sensor System 20
Hardware 21
Gocator 2000 Sensor 21
Gocator 2300 Sensor 22
Master 100 23
Master 200 24
Master 400/800 25
Master 1200/2400 26
Gocator 2000 Cordsets 27
Gocator 2300 Cordsets 27
Calibration Targets 28
Installation 29
Grounding - Gocator 29
Grounding - Master 400/800/1200/2400 29
Mounting 30
Orientations 31
Software 33
User Interface Overview 33
Connecting to a New Sensor 34
Running for the First Time 36
Running a Standalone Sensor System 36
Running a Dual Sensor System 38
Next Steps 42
Setup and Calibration 43
Setup Page 43
Table of Contents
Operation Modes 45
Data Viewer 46
Video Mode 46
Profile and Raw Mode 47
Whole Part 48
Region Definition 50
Data Viewer Controls 50
Height Map Color Scale 51
Profile Output 52
Coordinate Systems 52
Resampled And Raw Profile Format 53
Intensity Output 54
Trigger 55
Examples 57
Settings 59
Active Area 60
Tracking Window 61
Exposure 63
Single Exposure 64
Dynamic Exposure 65
Multiple Exposures 66
Resolutions 67
X Resolution 67
Z Resolution 68
Transformations 69
Dual Sensor System Layout 70
Overlap 71
Reverse 71
Calibration 72
Calibration States 72
Alignment vs. Travel Calibration 72
Alignment Calibration 73
Travel Calibration 74
Clearing Calibration 75
Filters 76
X Resampling Interval 77
Gap Filling 78
Smoothing 79
Part Detection 80
Measurement 82
Measurement Page 82
Adding and Removing Measurements 83
Changing the Measurement Name 84
Profile Sources 86
Decisions 87
Output Filters 88
Profile Fixturing 89

5Gocator 2000 & 2300 Series
Script Measurement 91
Built-in Functions 91
Profile Measurement Tools 95
Feature Points 102
Fit Lines 104
Measurement Types 105
Width 105
Height 106
Distance 107
Position X 108
Position Z 109
Center X 110
Center Z 111
Angle X 112
Intersect X 113
Intersect Z 114
Intersect Angle 115
Intersect Area 116
Box Area 117
Difference Area 118
Difference Peak 119
Circle Radius 120
Circle X 121
Circle Z 122
Line Standard Deviation 123
Line Error Min 124
Line Error Max 125
Line Percentile 126
Gap 127
Flush 132
Gap and Flush Algorithm 136
Groove Width 138
Groove X 140
Groove Z 142
Groove Algorithm 144
Strip Width 146
Strip Height 149
Strip X 152
Strip Z 155
Strip Detection Algorithm 158
Script 162
Whole Part Measurement Tools 163
Measurement Types 167
Area 167
Volume 168
Centroid X 169
Centroid Y 170
Centroid Z 171
Height 172
Ellipse Angle 173
Ellipse Minor 174
Ellipse Major 175
Ellipse Ratio 176
Bounding Box X 177
Bounding Box Y 178
Bounding Box Width 179
Bounding Box Length 180
Script 181
Output 182
Output Page 182
Ethernet Control and Output 183
Digital Outputs 187
Analog Output 190
Toolbar 193
Saving and Loading Settings 194
Managing Multiple Settings 196
Recording and Playback 197
Downloading, Exporting and Uploading
Recorded Data 198
Converting Recorded Data To Different Formats
200
Dashboard 201
Dashboard Page 201
State and Health Information 202
Metric Panel 204
Connection and Maintenance 205
Connection Page 205
Network Settings 206
Auto Starting Sensors 207
Overheat Temperature Protection 207
Buddy Assignment 208
Security 209
File Management 210
Maintenance 211
Firmware Upgrade 212

6Gocator 2000 & 2300 Series
Recovery 213
Sensor Recovery Tool 213
Gocator Configuration File 214
Setup 214
Profile 219
Part 240
Output 247
Calibration File 251
SysCal 252
Gocator Protocol 253
Concepts 254
Discovery 254
Command Channels 254
Result Channels 254
Modes 255
Buddy Communication Channels 255
States 255
Versions and Upgrades 255
Data Types 256
Profile Sources 256
Status Codes 256
Command and Reply Formats 257
Result Format 258
Discovery Commands 259
Get Address 259
Set Address 260
Upgrade Commands 261
Get Protocol Version 261
Start Upgrade 261
Get Upgrade Status 261
Get Upgrade Log 262
Control Commands 263
Get Protocol Version 263
Get System Info 263
Log In/Out 264
Change Password 265
Change Buddy 265
Get File List 265
Copy File 266
Read File 266
Write File 266
Delete File 267
Get Default File 267
Set Default File 268
Get Loaded File 268
Get Mode 268
Set Mode 269
Get Time 269
Get Encoder 269
Start 270
Scheduled Start 270
Stop 270
Trigger 271
Scheduled Digital Output 271
Scheduled Analog Output 272
Ping 272
Reset 272
Backup 273
Restore 273
Restore Factory 273
Set Connection Type 274
Get Connection Type 274
Clear Calibration 275
Data Results 276
Video 276
Profile 276
Profile Intensity 277
Part Profile 277
Part Intensity 278
Alignment Calibration 278
Travel Calibration 278
Exposure Calibration 279
Measurement 280
Health Results 282
Modbus TCP Protocol 284
Concepts 284
Messages 285
Registers 287
Control Registers 287
Output Registers 288
Measurement Registers 289
EtherNet/IP 290
Concept 290
Basic Object 291
Identity Object (Class 0x01) 291
TCP/IP Object (Class 0xF5) 291
Ethernet Link Object (Class 0xF6) 292
Assembly Object (Class 0x04) 293
Command Object 293
Sensor State Assembly Object 294
Sample State Assembly 295

7Gocator 2000 & 2300 Series
ASCII Protocol 296
Ethernet Communication 296
Asynchronous and Polling Operation 296
Serial Communication 296
Command and Reply Format 297
Special Characters 297
Standard Result Format 297
Custom Result Format 298
Control Commands 299
Start 299
Stop 299
Trigger 299
Load Configuration 300
Stamp 300
Alignment Calibration 301
Travel Calibration 301
Clear Calibration 301
Data Commands 302
Get Result 302
Get Value 302
Get Decision 303
Health Commands 304
Get Health 304
Software Development Kit 305
GenTL Driver 306
16-bit RGB Image 307
16-bit Grey Scale Image 308
Registers 310
Setting XML File 311
Troubleshooting 312
Mechanical/Environmental 312
Connection 312
Laser Profiling 312
Performance 313
Specification 314
Gocator 2000 Series 314
Gocator 2020 315
Gocator 2030 316
Gocator 2040 318
Gocator 2050 320
Gocator 2070 322
Gocator 2080 324
Gocator 2300 Series 326
Gocator 2330 327
Gocator 2340 329
Gocator 2350 331
Gocator 2370 333
Gocator 2380 335
Gocator 2000 I/O Connector 337
Grounding Shield 337
Power 337
Laser Safety Input 338
Digital Outputs 339
Digital Inputs 340
Encoder Input 341
Serial Output 341
Analog Output 342
Gocator 2300 Power/LAN Connector 343
Grounding Shield 343
Power 343
Laser Safety Input 344
Gocator 2300 I/O Connector 345
Grounding Shield 345
Digital Outputs 346
Digital Inputs 347
Encoder Input 347
Serial Output 348
Analog Output 349
Master 100 350
Master 100 Dimensions 351
Master 200 352
Master 200 Dimensions 354
Master 400/800 355
Master 400/800 Electrical Specifications 356
Master 400/800 Dimensions 357
Master 1200/2400 358
Master 1200/2400 Electrical Specifications 359
Master 1200/2400 Dimensions 359
Parts and Accessories 360
Warranty and Return Policy 363
Warranty Policy 363
Return Policy 363

8Gocator 2000 & 2300 Series
Software Licenses 364
Support 368

9Gocator 2000 & 2300 Series
Safety and Maintenance
Laser Safety
Gocator sensors contain semiconductor lasers that emit visible or
invisible light and are designated as Class 2M, Class 3R, or Class
3B, depending on the chosen laser option.
Gocator sensors are referred to as components, indicating that
they are sold only to qualified customers for incorporation into
their own equipment. These sensors do not incorporate safety
items that the customer may be required to provide in their own
equipment (e.g. remote interlocks, key control. Refer to references
for detail information). As such, these sensors do not fully comply
with the standards relating to laser products specified in IEC
60825-1 and FDA CFR Title 21 Part 1040.
!Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
References
1. International standard IEC 60825-1 (2001-08) consolidated edition, Safety of laser products – Part
1: Equipment classification, requirements and user’s guide.
2. Technical report 60825-10, Safety of laser products – Part 10. Application guidelines and
explanatory notes to IEC 60825-1.
3. Laser Notice No. 50, FDA and CDRH http://www.fda.gov/cdrh/rad-health.html
LASER
SENSOR
WARNING: DO NOT LOOK DIRECTLY
INTO THE LASER BEAM
LASER

Safety and Maintenance • 10Gocator 2000 & 2300 Series
Laser Classes
Class 2M laser components
Class 2M laser components would not cause permanent
damage to the eye under reasonably foreseeable
conditions of operation, provided that any exposure
can be terminated by the blink reflex (assumed to take
0.25 seconds). Because classification assumes the
blink reflex, the wavelength of light must be in the visible
range (400 nm to 700 nm). The Maximum Permissible
Exposure (MPE) for visible radiation for 0.25 seconds is
25 watts per square meter, which is equivalent to 1 mW
entering an aperture of 7 mm diameter (the assumed
size of the pupil).
IEC 60825-1:2007
LASER RADIATION
DO NOT STARE INTO THE BEAM
OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS OR MAGNIFIERS
CLASS 2M LASER PRODUCT
PEAK POWER:
EMITTED WAVELENGTH:
This product is designated for use solely as a
component and as such it does not fully comply
with the standards relating to laser products
specified in U.S. FDA CFR Title 21 part 1040
and IEC 60825-1
1 mW
660 nm
Class 3R laser components
Class 3R laser products emit radiation where direct
intrabeam viewing is potentially hazardous, but the
risk is lower with 3R lasers than for 3B lasers. Fewer
manufacturing requirements and control measures for
3R laser users apply than for 3B lasers.
IEC 60825-1:2007
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
PEAK POWER:
EMITTED WAVELENGTH:
This product is designated for use solely as a
component and as such it does not fully comply
with the standards relating to laser products
specified in U.S. FDA CFR Title 21 part 1040
and IEC 60825-1
5 mW
660 nm
Class 3B laser components
Class 3B components are unsafe for eye exposure.
Usually only ocular protection will be required. Diffuse
reflections are safe if viewed for less than 10 seconds.
IEC 60825-1:2007
LASER RADIATION
AVOID EXPOSURE TO THE BEAM
CLASS 3B LASER PRODUCT
PEAK POWER:
EMITTED WAVELENGTH:
This product is designated for use solely as a
component and as such it does not fully comply
with the standards relating to laser products
specified in U.S. FDA CFR Title 21 part 1040
and IEC 60825-1
130 mW
660 nm
IEC 60825-1:2007
LASER RADIATION
AVOID EXPOSURE TO THE BEAM
CLASS 3B LASER PRODUCT
PEAK POWER:
EMITTED WAVELENGTH:
This product is designated for use solely as a
component and as such it does not fully comply
with the standards relating to laser products
specified in U.S. FDA CFR Title 21 part 1040
and IEC 60825-1
450 mW
808 nm
Labels reprinted here are examples only. For accurate specifications, refer to the label on your sensor.

Safety and Maintenance • 11Gocator 2000 & 2300 Series
Precautions and Responsibilities
Precautions specified in IEC 60825-1 and FDA CFR Title 21 Part 1040 are as follows:
Requirement Class 2M Class 3R Class 3B
Remote interlock Not required Not required Required*
Key control Not required Not required Required – cannot remove
key when in use*
Power-on delays Not required Not required Required*
Beam attenuator Not required Not required Required*
Emission indicator Not required Not required Required*
Warning signs Not required Not required Required*
Beam path Not required Terminate beam at useful
length
Terminate beam at useful
length
Specular reflection Not required Prevent unintentional
reflections
Prevent unintentional
reflections
Eye protection Not required Not required Required under special
conditions
Laser safety officer Not required Not required Required
Training Not required Required for operator and
maintenance personnel
Required for operator and
maintenance personnel
*LMI Class 3B laser components do not incorporate these laser safety items. These items must be added and completed by the
customer in their system design.
Class 3B Responsibilities
LMI Technologies has filed reports with the FDA to assist customers in achieving certification of laser
products. These reports can be referenced by an accession number, provided upon request. Detailed
descriptions of the safety items that must be added to the system design are listed below.
Remote Interlock
A remote interlock connection must be present in Class 3B laser systems. This permits remote switches
to be attached in serial with the keylock switch on the controls. The deactivation of any remote switches
must prevent power from being supplied to any lasers.
Key Control
A key operated master control to the lasers is required that prevents any power from being supplied to
the lasers while in the OFF position. The key can be removed in the OFF position but the switch must not
allow the key to be removed from the lock while in the ON position.
Power-On Delays
A delay circuit is required that illuminates warning indicators for a short period of time prior to supplying
power to the lasers.
Beam Attenuators
A permanently attached method of preventing human access to laser radiation other than switches,
power connectors or key control must be employed. On some LMI laser sensors, the beam attenuator is
supplied with the sensor as an integrated mechanical shutter.
Emission Indicator
It is required that the controls that operate the sensors incorporate a visible or audible indicator when
power is applied and the lasers are operating. If the distance between the sensor and controls is more
than 2 meters, or mounting of sensors intervenes with observation of these indicators, then a second

Safety and Maintenance • 12Gocator 2000 & 2300 Series
power-on indicator should be mounted at some readily-observable position. When mounting the warning
indicators, it is important not to mount them in a location that would require human exposure to the laser
emissions. User must ensure that the emission indicator, if supplied by OEM, is visible when viewed
through protective eyewear.
Warning Signs
Laser warning signs must be located in the vicinity of the sensor such that they will be readily observed.
Examples of laser warning signs are as follows:
PEAK POWER
WAVELENGTH
100mW
600-780nm
CLASS IIIb LASER PRODUCT
INVISIBLE AND/OR VISIBLE LASER RADIATION
AVOID DIRECT EXPOSURE TO BEAM
DANGER
FDA warning sign example
IEC 60825-1:2007
CAUTION
AVOID EXPOSURE
TO THE BEAM
CLASS 3B LASER LIGHT
IEC warning sign example
Systems Sold or Used in the USA
Systems that incorporate laser components or laser products manufactured by LMI Technologies require
certification by the FDA.
Customers are responsible for achieving and maintaining this certification.
Customers are advised to obtain the information booklet Regulations for the Administration and
Enforcement of the Radiation Control for Health and Safety Act of 1968: HHS Publication FDA 88-8035.
This publication, containing the full details of laser safety requirements, can be obtained directly from the
FDA, or downloaded from their web site at http://www.fda.gov/cdrh.

Safety and Maintenance • 13Gocator 2000 & 2300 Series
Electrical Safety
Sensors should be connected to earth ground
All sensors should be connected to earth ground through their housing. All sensors should be mounted
on an earth grounded frame using electrically conductive hardware to ensure the housing of the sensor
is connected to earth ground. Use a multi-meter to check the continuity between the sensor connector
and earth ground to ensure a proper connection.
Minimize voltage potential between system ground and sensor ground
Care should be taken to minimize the voltage potential between system ground (ground reference for
I/O signals) and sensor ground. This voltage potential can be determined by measuring the voltage
between Analog_out- and system ground. The maximum permissible voltage potential is 12 V but should
be kept below 10 V to avoid damage to the serial and encoder connections. Refer to Gocator 2000 I/O
Connector (page 337) and Gocator 2300 I/O Connector (page 345) for a description of connector
pins.
Use a suitable power supply
The +24 to +48 VDC power supply used with Gocator sensors should be an isolated supply with inrush
current protection or be able to handle a high capacitive load.
Use care when handling powered devices
Wires connecting to the sensor should not be handled while the sensor is powered. Doing so may cause
electrical shock to the user or damage to the equipment.
!Failure to adhere to the guidelines described in this section may result in electrical shock or equipment
damage.

Safety and Maintenance • 14Gocator 2000 & 2300 Series
Environment and Lighting
Avoid strong ambient light sources
The imager used in this product is highly sensitive to ambient light hence stray light may have adverse
effects on measurement. Do not operate this device near windows or lighting fixtures that could influence
measurement. If the unit must be installed in an environment with high ambient light levels, a lighting
shield or similar device may need to be installed to prevent light from affecting measurement.
Avoid installing sensors in hazardous environments
To ensure reliable operation and to prevent damage to Gocator sensors, avoid installing the sensor in
locations;
• that are humid, dusty, or poorly ventilated
• with a high temperature, such as places exposed to direct sunlight
• where there are flammable or corrosive gases
• where the unit may be directly subjected to harsh vibration or impact
• where water, oil, or chemicals may splash onto the unit
• where static electricity is easily generated
Ensure that ambient conditions are within specifications
Gocator sensors are suitable for operation between 0 – 50 °C and 25 – 85% relative humidity (non-
condensing). Measurement error due to temperature is limited to 0.015% of full scale per degree C.
The Master 200/400/800/1200/2400 is similarly rated for operation between 0 – 50 °C.
The storage temperature is -30 – 70 °C.
!
It is critical that the sensor is heat sunk through the frame it is mounted to. When a sensor is properly heat
sunk, the difference between ambient temperature and the temperature reported in the sensor's health
channel is less than 15 °C.
!
Gocator sensors are high accuracy devices. It is critical that the temperature of all of its components are in
equilibrium. When the sensor is powered up, a warm-up time of at least one hour is required in order to reach
a consistent spread of temperature within the sensor.
Sensor Maintenance
Keep sensor windows clean
Gocator sensors are high-precision optical instruments. To ensure the highest accuracy is achieved in all
measurements, the windows on the front of the sensor should be kept clean and clear of debris.
Use care when cleaning sensor windows
Use dry, clean air to remove dust or other dirt particles. If dirt remains, clean the windows carefully with a
soft, lint-free cloth and non-streaking glass cleaner or isopropyl alcohol. Ensure that no residue is left on
the windows after cleaning.
Turn off lasers when not in use
LMI Technologies uses semiconductor lasers in 3D measurement sensors. To maximize the lifespan of
the sensor, turn off the laser when not in use.

Safety and Maintenance • 15Gocator 2000 & 2300 Series
Avoid excessive modifications to files stored on the sensor
Settings for Gocator sensors are stored in flash memory inside the sensor. Flash memory has an
expected lifetime of 100,000 writes. To maximize lifetime, avoid frequent or unnecessary file save
operations.

16Gocator 2000 & 2300 Series
System Overview
Gocator sensors can be installed and used in a variety of scenarios. Sensors can be connected as
standalone devices, dual sensor (Main and Buddy) system, or multi-sensor system.
Standalone System
Standalone systems are typically used when only a single Gocator sensor is required. The sensor can
be connected to a computer’s Ethernet port for setup and can also be connected to devices such as
encoders, photocells, or PLCs.
GOCATOR I/O
CORDSET
ETHERNET
CORDSET
USER PC
(can be disconnected after setup)
GOCATOR
CONNECT POWER AND I/O AS
REQUIRED BY APPLICATION
IN - ENCODER / TRIGGER / SAFETY
OUT - SERIAL / ANALOG / DIGITAL
GOCATOR 2000 SERIES
Getting Started

Getting Started • 17Gocator 2000 & 2300 Series
GOCATOR
I/O CORDSET
POWER & ETHERNET
CORDSET
USER PC
(can be disconnected
after setup)
POWER: 24-48VDC @ 13W
LASER SAFETY: +24-48VDC TO ENABLE
WIRE RICH I/O
AS REQUIRED BY APPLICATION
IN - ENCODER / TRIGGER
OUT - SERIAL / ANALOG / DIGITAL
GOCATOR
GOCATOR 2300 SERIES

Getting Started • 18Gocator 2000 & 2300 Series
Dual Sensor System
In a dual sensor system, two Gocator sensors work together to perform profiling and output the
combined results. The controlling sensor is referred to as the Main sensor, and the helper is referred to
as the Buddy sensor. Gocator’s software recognizes three installation orientations – None, Opposite and
Wide.
For the Gocator 2000 series sensors, the Master 200 must be used to connect two sensors in a Dual
Sensor (Buddy) system. Gocator 20x0 I/O cordsets are used to connect sensors to the Master 200. The
Master 200 provides a single point of connection for system I/O and power. The Master 200 ensures
that the scan timing is precisely synchronized across sensors. Sensors and client computers typically
communicate via an Ethernet switch (minimum 100 Mbit/s).
MASTER 200
CAT5E ETHERNET
CABLE
GOCATOR I/O
CORDSET ETHERNET
CORDSET
ETHERNET SWITCH
(NOT SUPPLIED
(BY LMI)
USER PC
MAIN GOCATOR
BUDDY GOCATOR
CONNECT I/O AS REQUIRED BY
APPLICATION
IN - ENCODER / TRIGGER / SAFETY
OUT - SERIAL / ANALOG / DIGITAL
GOCATOR 2000 SERIES
For the Gocator 2300 series sensors, a Master 400/800/1200/2400 must be used to connect two sensors
in a Dual Sensor (Buddy) system. Gocator 23x0 Master cordsets are used to connect sensors to the
Master.

Getting Started • 19Gocator 2000 & 2300 Series
GOCATOR I/O
CORDSET
GOCATOR
POWER AND ETHERNET
CORDSET
POWER, LASER SAFETY,
TRIGGER INPUTS, ENCODER
MAIN GOCATOR
BUDDY GOCATOR
GOCATOR 2300 SERIES
GIGABIT ETHERNET SWITCH
MASTER 400/800/1200/2400

Getting Started • 20Gocator 2000 & 2300 Series
Multi-Sensor System
Master 400/800/1200/2400 networking hardware can be used to connect two or more sensors into
a Multi-sensor system. Gocator Master cordsets are used to connect the sensors to a Master. The
Master provides a single point of connection for power, safety, encoder and digital inputs. A Master
400/800/1200/2400 can be used to ensure that the scan timing is precisely synchronized across
sensors. Sensors and client computers communicate via an Ethernet switch (minimum 100 Mbit/s).
Unlike the Master 200, Master 400/800/1200/2400 does not support digital, serial or analog output.
MASTER 400/800/1200/2400
USER PC
GIGABIT ETHERNET SWITCH
CAT5E ETHERNET CABLE
GOCATOR MASTER CORDSET
ETHERNET CORDSET
GOCATOR 2000 SERIES
POWER, LASER SAFETY,
TRIGGER INPUTS, ENCODER
GOCATOR
MASTER 400/800/1200/2400
USER PC
GIGABIT ETHERNET SWITCH
CAT5E ETHERNET CABLE
GOCATOR POWER AND ETHERNET
TO MASTER CORDSET
GOCATOR 2300 SERIES
POWER, LASER SAFETY,
TRIGGER INPUTS, ENCODER
GOCATOR