Loll Designs LOLLYGAGGER PICNIC TABLE User manual

PRODUCT CARE
Your new Loll furniture is a no maintenance product. You’ll never need to paint or stain it and it can be
left outside all year regardless of the season. It will not rot, even if left standing in water. Nonetheless,
we’re pretty sure your Loll furniture will get a lot of use and will at some point need cleaning. We
recommend a garden hose and incorporating a soft bristle brush. Adding a tablespoon or two of your
favorite eco-friendly soap to the wash will get everything squeaky clean. Mineral deposits left over
from hard water can be removed with a solution of vinegar and water. Loll offers a cleaning kit that has
everything you need for great results. Also see our cleaning video at lolldesigns.com/videos.
5 YR WARRANTY
Loll Designs strives to build long-term relationships based on confidence and trust with our customers.
We sit beside, on top, and beneath the quality of our fine furniture and will make things right if you
are not completely satisfied with your purchase. Loll Designs hereby guarantees that the piece will be
of good quality and workmanship, free from faults and defects. Loll warrants that all components will
not fail, under normal use, for five years from the year mark on the piece or the date of purchase. *For
commercial orders the warranty is three years.
SHARE YOUR LOLL
ASSEMBLY INSTRUCTIONS & PRODUCT INFO:
We want you to love your Loll.
Reach out if you need
lollygagging assistance.
877-740-3387
[email protected]
5912 Waseca Street | Duluth, Minnesota 55807
DAMAGED PRODUCT
Sometimes accidents occur. Please inspect your Loll furniture when you receive it to make sure that
it has not been damaged during shipping. If damage has occurred please take digital pictures of the
damaged furniture and the box it was shipped in, and email them to [email protected] or call
Customer Service using our toll free number: 877.740.3387, ext. 1. The damage will be assessed and
you will be contacted with a solution to the problem. It may be helpful to save all of your packaging
material in case a return is necessary.
ASSEMBLY TIPS
*Please read before beginning assembly!
To avoid damaging furniture perform the assembly of your Loll furniture on a clean
soft surface like a blanket, carpet, or the flattened cardboard box the furniture
was shipped in. Components should not be unnecessarily forced together! If
it seems parts aren’t fitting together you likely have something wrong and you
should reread the instructions to ensure you are aligning the proper components.
If your piece of furniture requires “Blocks” for assembly one side may have
protective film on it. This surface is hidden after assembly so the film can remain
on the block or it can be removed. Use a Cordless Screw Gun if you have one
and know how to use it. Set the clutch setting at medium torque. We do not
recommend using an electric drill with a cord and without a clutch to install bolts
in inserts as you can easily overtighten and damage the product. All bolts come
standard with a thread coating to reduce bolts loosening after assembly while
still allowing removal and reuse of the bolt. Start all bolts by hand, with the Allen
Key, or the Loll Tool and tighten firmly until parts are drawn tight together and
you can’t muscle the bolt any tighter. It’s virtually impossible to over tighten by
hand. Watch the assembly videos at www.lolldesigns.com/videos for even more
information and visual aids. If you have more questions please contact your Loll
Sales Associate or Customer Service for support at 877.740.3387. A
Pro Tool Kit
can also be purchased from Loll for multi piece assembly jobs.
** Please Recycle the BOX and paper packaging. The green plastic stretch
wrap we use is compostable.
LOLL TOOL
Locate the box marked
“Tool Included”
before beginning assembly.
BLOCK & BOLT INSTALLATION
Insert bolts through countersunk hole side of blocks as shown below.
CORRECT INCORRECT
Countersunk
Hole
Scan for assembly
tips and videos
lolldesigns.com
877.740.3387
Loll Designs inspires people to appreciate the outdoors.
LOLLYGAGGER PICNIC TABLE
2
COUNT
SIDE RAILS 2
COUNT
CENTER RAILS 1
COUNT
TOP SLATS 2
COUNT
SIDE
2
COUNT
LEG BLOCK SET 2
COUNT
LEG SET 34
COUNT
SQUARE BLOCK 50
COUNT
7/8˝ BOLTS
(YELLOW)
INCLUDED PARTS

ASSEMBLY INSTRUCTIONS
ATTACH CENTER RAILS
ATTACH LEGS
ATTACH SIDE RAILS
ATTACH TOP SLATS
1
3
2
4
*Please read Assembly Tips before beginning assembly.
Arrange Center Rails with cut outs toward the bottom and to each other as shown
above. Inside the pocket cut out there is an engraving indicating L=Left or R=Right.
Insert ends of Center Rails into Sides middle set of cut outs. Place Square Blocks
(recessed hole side out) into the Center Rail cut outs and insert 7/8˝ bolts through
the blocks into threaded holes of the Side and tighten. Repeat for opposite Side.
Fit long cut out in Legs with edges of Sides. Legs holes will align with holes in Leg
Blocks. Insert bolts through the Leg Block holes into threaded holes of the Leg and
tighten.
Place Square Blocks into cut outs of the Sides. Attach to legs using bolts provided.
Repeat for second set of Legs.
Fit Right Side Rail cut outs with edges of Sides. Use a set of Leg Blocks to attach
Right Side Rail by fitting the blocks into the Side cut out and inserting bolts through
the blocks into the threaded holes in the rail. Repeat for Left Side Rail.
Lay Table Top Slats upside down on a clean flat surface arranged in the order
shown above. Fit assembled Rails and Sides with cut outs in Top Slats. Attach using
Square Blocks and Bolts.
Complete assembly by securely tightening all bolts using provided wrench.
* It is very important that you finger tighten all bolts into inserts to ensure that you do not cross-thread bolts and inserts before tightening. It
will also be easier if you wait to tighten bolts until you have all bolts installed and the piece completely assembled. This will allow for more
movement of individual pieces and help in aligning holes with inserts. Use the Allen Tool provided to finish tighten bolt until snug.
= 4
= 16
A
B
C
A
= 8
= 22