Loll Designs Racer rocker User manual

ASSEMBLY INSTRUCTIONS
ATTACH BACKATTACH LOWER SHELF & BACK PLATE
ATTACH TOP BRACE
ATTACH SEAT BRACE
ATTACH SEAT & BRACEATTACH FACE PLATE
ATTACH SEAT SET
ATTACH BACK SET
11
3
5
22
4
6
*Please read Assembly Tips before beginning assembly.
Fit Back edge into Left Side groove track cut out with the pocket cut out in the Back facing
the threaded insert in the Left Side. Place Block B into Back’s pocket cut out and insert bolt
through the block into Left Side threaded hole and finger tighten.
*Please read Assembly Tips before beginning assembly.
Fit edge of Lower Shelf that has holes through it into the groove track cut out of the Back
Plate, and fit both pieces into the groove track cut outs of the Left Side. Place G Blocks into
the Lower Shelf and Back Plates pocket cut outs, insert bolts through the blocks into the Left
Sides threaded holes, and finger tighten
Fit Top Brace edge into Left Side’s pocket cut out. Place G Blocks into the Top Brace’s
pocket cut out, insert a bolt through the block into the Left Side’s threaded holes, and finger
tighten.
*Repeat steps 1-3 to attach Right Side.
Align Seat Brace holes with the holes of the Seat Set, then insert bolts through the Seat
Brace into the Seat Set’s threaded holes and finger tighten.
Fit Seat edge into Left Side groove track cut out so that the groove track cuts in the Seat line
up with the groove track cut outs in the Left Side. Place Block B into Seats pocket cut out,
insert bolts through the block into Left Sides threaded holes, and finger tighten. Fit long edge
of the Seat Brace in the Seats groove track cut out and the short end of the Seat Brace into
the Left Sides pocket cut out.
Fit Face Plate short edge into the Left Side’s pocket cut out. Place G Block into the Face
Plate’s pocket cut out, insert a bolt through the block into the Left Side’s threaded hole, and
finger tighten.
Repeat steps 1 & 2 to attach Right Side.
Layout the Seat Set so that the groove track cut outs line up. Place Seat Set individually over
assembled chair sides (start with A then B and C) by fitting the groove track cut outs with the
Sides and Front Plate. Place G Blocks into the Sides pocket cut outs, insert bolts through the
blocks into the Seat Sets threaded holes, and finger tighten.
Layout the Back Set so that the groove track cut outs line up. Place Back Set individually
over assembled chair sides (start with A then B, C, D) by fitting the groove track cut outs with
the Sides and Front Plate. Place G Blocks into the Sides pocket cut outs, insert bolts through
the blocks into the Back Sets threaded holes, and finger tighten.
*Note: Use same color G Block as Racing Stripe color.
**Using provided wrench securely tighten all bolts.
* It is very important that you finger tighten all bolts into inserts to ensure that you do not cross-thread bolts and inserts before tightening. It
will also be easier if you wait to tighten bolts until you have all bolts installed and the piece completely assembled. This will allow for more
movement of individual pieces and help in aligning holes with inserts. Use the Allen Tool provided to finish tighten bolt until snug.
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6
Step 1 Step 2
Step 3 And repeat on other side
Step 4 Step 5 Step 6

PRODUCT CARE
Your new Loll furniture is a no maintenance product. You’ll never need to paint or stain it and it can be
left outside all year regardless of the season. It will not rot, even if left standing in water. Nonetheless,
we’re pretty sure your Loll furniture will get a lot of use and will at some point need cleaning. We
recommend a garden hose and incorporating a soft bristle brush. Adding a tablespoon or two of your
favorite eco-friendly soap to the wash will get everything squeaky clean. Mineral deposits left over
from hard water can be removed with a solution of vinegar and water. Loll offers a cleaning kit that has
everything you need for great results. Also see our cleaning video at lolldesigns.com/videos.
5 YR WARRANTY
Loll Designs strives to build long-term relationships based on confidence and trust with our customers.
We sit beside, on top, and beneath the quality of our fine furniture and will make things right if you
are not completely satisfied with your purchase. Loll Designs hereby guarantees that the piece will be
of good quality and workmanship, free from faults and defects. Loll warrants that all components will
not fail, under normal use, for five years from the year mark on the piece or the date of purchase. *For
commercial orders the warranty is three years.
SHARE YOUR LOLL
ASSEMBLY INSTRUCTIONS & PRODUCT INFO:
We want you to love your Loll.
Reach out if you need
lollygagging assistance.
877-740-3387
[email protected]
5912 Waseca Street | Duluth, Minnesota 55807
DAMAGED PRODUCT
Sometimes accidents occur. Please inspect your Loll furniture when you receive it to make sure that
it has not been damaged during shipping. If damage has occurred please take digital pictures of the
damaged furniture and the box it was shipped in, and email them to [email protected] or call
Customer Service using our toll free number: 877.740.3387, ext. 1. The damage will be assessed and
you will be contacted with a solution to the problem. It may be helpful to save all of your packaging
material in case a return is necessary.
ASSEMBLY TIPS
*Please read before beginning assembly!
To avoid damaging furniture perform the assembly of your Loll furniture on a clean
soft surface like a blanket, carpet, or the flattened cardboard box the furniture
was shipped in. Components should not be unnecessarily forced together! If
it seems parts aren’t fitting together you likely have something wrong and you
should reread the instructions to ensure you are aligning the proper components.
If your piece of furniture requires “Blocks” for assembly one side may have
protective film on it. This surface is hidden after assembly so the film can remain
on the block or it can be removed. Use a Cordless Screw Gun if you have one
and know how to use it. Set the clutch setting at medium torque. We do not
recommend using an electric drill with a cord and without a clutch to install bolts
in inserts as you can easily overtighten and damage the product. All bolts come
standard with a thread coating to reduce bolts loosening after assembly while
still allowing removal and reuse of the bolt. Start all bolts by hand, with the Allen
Key, or the Loll Tool and tighten firmly until parts are drawn tight together and
you can’t muscle the bolt any tighter. It’s virtually impossible to over tighten by
hand. Watch the assembly videos at www.lolldesigns.com/videos for even more
information and visual aids. If you have more questions please contact your Loll
Sales Associate or Customer Service for support at 877.740.3387. A
Pro Tool Kit
can also be purchased from Loll for multi piece assembly jobs.
** Please Recycle the BOX and paper packaging. The green plastic stretch
wrap we use is compostable.
LOLL TOOL
Locate the box marked
“Tool Included”
before beginning assembly.
BLOCK & BOLT INSTALLATION
Insert bolts through countersunk hole side of blocks as shown below.
CORRECT INCORRECT
Countersunk
Hole
Scan for assembly
tips and videos
lolldesigns.com
877.740.3387
Loll Designs inspires people to appreciate the outdoors.
RACER ROCKER CHAIR
1
COUNT
LEFT SIDE
1
COUNT
BACK SET
1
COUNT
FACE PLATE
1
COUNT
TOP BRACE
22
COUNT
G BLOCK
1
COUNT
BACK PLATE
1
COUNT
SEAT BRACE
1
COUNT
LOWER SHELF
25
COUNT
7/8˝ BOLT
(YELLOW)
1
COUNT
RIGHT SIDE 1
COUNT
SEAT SET
INCLUDED PARTS
Left Side
Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate
Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate
Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate
Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate
Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
1/2" G Block
Left Side Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
Left Side Right Side
Back Plate Top Brace
Face Plate Shelf
Seat Brace
G Block X 22 7/8" Bolt (Yellow) X 25
Back Set
Seat Set
*Note: 2 Blocks will be same color
as Racing Stripe (see Step 6)
A.
A.
B.
B.
C.
C.
D.