Lopi 250-05675 User manual

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 1 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
Compatibility
AGP Inserts with removable HRD top - SN# 2402-002235 to 2112-001250.
NOTE: Units made after SN# 2112-001250 will have the removable hopper funnel and do not need this kit.
Packing List
Hopper assembly
Tools Needed
11/32” nut driver
1/4” nut driver
5/16” nut driver
3/8” nut driver
Phillips screwdriver
Diagonal cutters
Installation
Make sure the stove has fully cooled (approximately 45 minutes) before conducting service. Unplug the
stove to prevent electrical shock.
1. Remove the insert side covers. Each side cover is secured to the insert with two screws (see left
picture below). Use a Phillips screwdriver to loosen these screws but do not remove them.

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 2 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
2. Slide the (2) insert side covers forward and set aside for reinstallation.
NOTE: Later, when re-installing the side panel, make sure the tabs on the panel insert into the slots on
the front of the insert.
The tabs on the side
panels have keyhole
slots that engage the
screws

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 3 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
3. Remove the Control board assembly from the surround panel by loosening the wing nut and then
slide the assembly up to disengage the bottom tabs from the bracket on the panel. After the bottom
is free, slide the assembly downward until the assembly is free from the wingnut stud.
Loosen
wingnu
t

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 4 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
4. Remove surround panels. Pull the panels a little forward of the insert to gain access to the back of
the control board and disconnect the wire harness. Carefully guide the surround panel over the
hopper lid taking care to prevent scratching the paint.
5. Use a 1/4” nut driver to remove the (2) screws that secure the surround panel mounting brackets to
the insert (both sides of the insert). Carefully cut the (3) zip ties indicated below.
Remove using
Cut with

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 5 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
6. Disconnect the (2) wires from the hopper lid switch from the main harness using the quick connects
shown below.
7. Remove the (5) 11/32” nuts that secure the hopper lid to the insert (set aside for reinstallation).
Remove the hopper lid and set it aside to be reinstalled on the replacement hopper assembly.
8. Remove the (4) 1/4” screws that secure the louvers from the front of the insert, keep the screws, and
set the louvers aside to be reinstalled.
Remove using
Remove using

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 6 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
9. Remove the (12) 1/4” and the (8) 3/8” screws shown below (set screws aside for reinstallation).
Hopper Snap Disc to allow for hopper removal.
10. Remove the hopper snap disk from the snap disk bracket. You can leave the wires attached to
the disk.
Remove using
Remove using Remove using
Remove using
Remove using
Remove using
Rear of the Convective
Air Chamber
Right Side of Inser
t
Left Side of Insert
Left Side of Insert

AGP Insert Hopper Replacement
(SKU 250-05675)
Page 7 of 7 17602198.docx — 1/8/21 © Travis Industries, Inc.
11. Remove the (2) screws that secure the rear of the hopper to the rear hopper support (keep
screws for reinstallation).
12. Lift the hopper assembly straight up and remove it from the insert.
13. Install the replacement hopper by following the steps above, in reverse. Make sure all wires are
reconnected and all removed screws are replaced. Test the appliance for proper operation.
Rear of the
Hopper
Remove using