Lopi 99200139 User manual

Outside Air Kit
sku# 99200139
Page 1 of 2 17601452 - 9/30/20 © Travis Industries, Inc.
Compatibility:
• All Lopi Wood Stoves • Deerfield Pellet Stove • Foxfire Pellet Stove
Packing List:
Outside Air Duct Assembly
Hood (includes rodent screen)
Flashing
3” Duct (4’ long)
(2) Hose Clamps
(2) 1” Wood Screws
(2) #8 Screws (for securing air duct assembly to stoves with legs).
(2) 1-1/2” Wood Screws
(2) Drywall Anchors (for securing the hood and flashing)
Answer Cover Plate and Gasket
Homefire Cover Plate and Gasket
Cover Plate (ANSWER & HOMEFIRE ONLY)
When using outside air with the Answer or HomeFire stoves, a replacement cover plate is required to ensure
combustion air is drawn from below.
Cover Plate Replacement
a. Remove the bridge plate – Remove the (2) screws that secure the bridge plate to the air control
plate (set aside for reinstallation). Remove the air control plate and gasket – Remove the (2)
screws that secure the air control plate to the air control.
b. Discard the stock air control plate and gasket.
c. Install the replacement air control plate and gasket – secure the plate and gasket to the air
control using the (2) screws removed in step (a). Reinstall the bridge plate and secure using the
screws removed in step (a).
HomeFire Cover Plate
and Gasket
Answer Cover Plate
and Gasket
8-1/4” 6-1/2”
8-5/16” 6-5/16”
Air Control Rod
B
ridge Plate
Air Control Plate
(with gasket)
a
b

Outside Air Kit
sku# 99200139
Page 2 of 2 17601452 - 9/30/20 © Travis Industries, Inc.
Outside Air Knock-Out (ANSWER & HOMEFIRE ONLY)
Remove the forward knock-out on the bottom
of the stove.
Installation
Outside Air Knock-Out
Rear Blower Knock-Outs
FRONT OF STOVE















































3" Dia. Flex Duct
(4' max. length)
Hood with Rodent Screen
Silicone
Seal the area around
the tube to prevent
air from entering
through the wall.
Silicone













All Stoves Except Leyden,
Arbor, Cape Cod:
Secure flex duct to air duct
assembly using the included
hose clamp. Attach air duct
assembly to stove with two
included #8 screws.
Slide the cover plate
over the flex duct then
attach the flex duct to
the hood with the
included hose clamp.
Secure the cover plate
to the wall with the
included screws (and
drywall anchors if
needed).
HINT: The flex must be
fully stretched and the
ends cut square and
flatted for it to fit
properly. The tube on
the hood and air duct
may be crimped if
necessary.

Cover Plate











Stove
b
8"
Select a location between
framing members for the
wall penetration.
NOTE: If wall is thicker
than 8", attach the flex duct
to the hood then slide the
hood into place.
c
Leyden/Arbor:
Remove the outside air cover
from the bottom of the stove.
Insert the start collar into the
air cover and tap into place
with a mallet. Secure the flex
duct to the start collar using the
included hose clamp.
Cape Cod:
Secure flex duct to air duct
assembly at the rear of the stove
using the included hose clamp.
a
Slide the hood
through the wall
and secure to the
outside wall with
the two included
screws.
Endeavor, Liberty, Evergreen,
Rockport & Cape Cod
Use the included hose clamp to
secure the flex duct to the 3” air
inlet collar at the bottom rear of
the appliance